Breville The 3X Bluicer Pro Instruction Manual

the 3X Bluicer Pro™Instruction Book – BJB815

BREVILLE RECOMMENDS SAFETY FIRST

At Breville we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In  addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.

IMPORTANT SAFEGUARDSREAD ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE

  • Before using the first time ensure your electricity supply is the same as shown on the label on the underside of the appliance. This appliance is equipped with a  power cord having a grounding wire with a grounding plug. The appliance must be grounded using a properly grounded outlet. In the event of an electrical fault,  grounding reduces the risk of electrical shock.
  • Do not, under any circumstances, cut or remove the third (ground) prong from the power cord or use an adapter.
  • Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
  • The installation of a residual current safety switch is recommended to provide additional safety when using all electrical appliances. Safety switches with a ratedoperating current not more than 30mA are recommended. Consult an electrician for professional advice.
  • Remove and discard any packaging materials safely, before first use.
  • To eliminate a choking hazard for young children, discard the protective cover fitted to the power plug safely.
  • Always ensure the appliance is properly assembled, as per instructions, before use. Using the appliance without being properly assembled may cause product  malfunction, product damage or pose safety risk including personal injury.
  • This appliance is for household use only. Do not use the appliance for anything other than its intended purpose. Do not use in moving vehicles or boats. Do not use outdoors. Misuse may cause injury.
  • Position the appliance on a stable, heat resistant, level, dry surface away from the counter edge, and do not operate on or near a heat source such as a hot plate,  oven or gas hob.
  • Fully unwind the power cord before operating.
  • Do not let the power cord hang over the edge of a counter or table. Do not let the power cord touch hot surfaces or become knotted.
  • Do not leave the appliance unattended when in use.
  • If the appliance is to be left unattended, cleaned, moved, assembled or stored, always switch off the appliance by pressing the ON | OFF button to OFF. Switch off and unplug from the power outlet.
  • Turn the appliance OFF, then unplug from the outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug  and pull from the outlet. Never pull from the power cord.
  • Regularly inspect the power cord, plug and actual appliance for any damage. If found to be damaged in any way, immediately cease use of the appliance and  return the entire appliance to the nearest authorised Breville Service Centre for examination, replacement or repair.
  • Keep the appliance and accessories clean. Follow the cleaning instructions provided in this book. Any procedure not listed in this instruction booklet should beperformed at an authorisedBreville ® Service Centre.
  • This appliance is not intended for use by children or by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge. Close supervision is necessary when any appliance is used near children. Children should be supervised to ensure that they do not play with the appliance.
  • Children should not play with the appliance.
  • Cleaning of the appliance should not be carried out by children.
  • The appliance power cord, and any components, attachments or accessories should be kept out of reach of children aged 8 years and younger.
  • Never use attachments or accessories that are not supplied with this product or authorised by Breville to be used on this product. Failing to follow this instruction may cause product malfunction, product damage or even pose safety risk.
  • Do not attempt to operate the appliance by any method other than those described in this booklet.
  • Do not move the appliance while in operation.
  • Do not operate the appliance on an inclined surface.
  • Do not push food into the feed chute with your fingers or other utensils. Always use the food pusher provided. Do not place hand or fingers into the food  chute when it is attached to the appliance.
  • Do not juice stone fruit unless seeds and/or stones have been removed.
  • Make sure the product is turned OFF and the stainless-steel filter basket has stopped rotating and the motor has completely stopped before releasing the safety locking arm and/or attempting to move the appliance, when the unit is not in use, and before disassembling, cleaning and storing.
  • Any significant spillage onto the surface under or around the appliance, or onto the appliance itself, should be cleaned and dried before continuing to use the appliance.
  • Be careful when handling the stainless-steel filter basket as the small cutting blades at the base of the filter basket are very sharp. Mishandling may cause injury.
  • Blender blades are sharp, take care when handling, emptying and cleaning the blender jug.Remove rind from all citrus fruit before juicing.
  • Do not use the appliance if the rotating sieve (filter basket) or lid is damaged.
  • Always make sure chute cover is clamped securely in place before motor is turned on.
  • Do not operate without the pulp container in place.
  • Do not unfasten interlock arm while unit is in operation.
  • A representative example of the heaviest loading anticipated for use with this appliance is 450g of frozen banana pieces and 1000g of milk blended on the highest speed for 30 seconds.
  • Do not juice more than 3kg (approximately 6 pounds) of carrot at a time.
  • Avoid putting the blender jug on the motor base while the motor is still spinning.
  • Do not operate without any ingredients in the jug.
  • Never attempt to operate with damaged blades, or with utensils, or any foreign objects inside the jug.
  • Do not put the jug in extremes of heat or cold, for example placing a cold jug into hot water, or vice versa.
  • Lid must be firmly secured to the jug before operation to ensure internal contents do not escape, spray or overflow.
  • Do not remove the jug from the motor base while blender is in use.
  • Do not use blender while OVERLOAD PROTECTION is flashing on the LCD. If this occurs, unplug the blender and wait for 30 minutes until the motor has  cooled. Once cooled, you will be able to use the blender as usual again.
  • Do not process hot or boiling liquids. Allow to cool before placing into the blender jug.
  • To protect against electric shock, do not immerse the power plug, cord or appliance in water or any liquid.
  • Authorised Breville Service Centres can be found on our website www.Breville.com

FOR HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS

Components

A. Food pusher (not dishwasher safe)B. Juicer cover (dishwasher safe)C. Stainless steel filter basket (dishwasher safe)D. Filter bowl surround (dishwasher safe)E. Interlocking safety arm Stops motor base operating without cover locked into place.F. Control panelG. Stainless steel motor baseH. Inner measuring cup (dishwasher safe)I. 1.5 litre blending jug & lid (dishwasher safe)J. Juicing nozzle (dishwasher safe) Can be placed over spout to juice directly into a cup.K. Drip stop plugL. Pulp container (dishwasher safe)M. Cleaning brush For use on Stainless Steel Filter Basket.

Assembly

BEFORE FIRST USEWash the lid, inner measuring cup, jug, the filter bowl surround, filter basket, juicer cover, food pusher and pulp container in warm, soapy water with a soft cloth.  Rinse and dry thoroughly. Place motor base on a flat, dry surface such as a countertop. Ensure that the appliance is switched to OFF at the motor base and the power cord is unplugged.JUICING1. Place filter bowl surround on top of the motor base.

2. Align the arrows at the base of the stainless-steel filter basket with the arrows on the motor drive coupling and push down until it clicks into place to create a  secure fit with the motor base.

3. Place the juicer cover over the filter bowl surround, positioning the lower part of the feed chute over the stainless steel filter basket.

4. Raise the safety locking arm up and locate into the two grooves on either side of the juicer cover.

5. The safety locking arm should now be in a vertical position and locked into place on top of the juicer cover.

6. Slide the food pusher down the food chute by aligning the groove in the food pusher, with the small protrusion on the inside of the top of the feed tube.

7. Place the pulp container into position by tilting and lifting the motor base slightly. Insert the pulp container under the juicer cover on the back ensuring the  front edge is tucked under the back lip of the filter bowl surround and the bottom edge is clipped into the bottom of the motor base.

8. Drip stop plug can be fitted over juice outlet nozzle. It then allows the outlet to be plugged to prevent dripping after juicing.

9. Fit the lid to the blender jug and position jugunder juice spout.

10. Optional: For juicing into a cup the Juicing Nozzle can be fitted onto the juice outlet nozzle.

BLENDING1. With the blender jug in the upright position place it on the motor base. The handle of the blender can be positioned to the left or right-hand side of the appliance.

2. Raise the safety locking arm up and locate into the two grooves on either side of the blender.

3. Add food or liquid into the blender jug ensuring not to exceed the ‘MAX’ mark. Place the blender lid firmly into position on the top of the blender jug. Insert  the clear, inner measuring lid into the blender lid and turn clockwise to lock into position. The jug features a Breville® Assist™ Lid. This allows the lid to fit  tightly onto the blender jug, avoiding displacement during operation.4. Ensure the spout cover of the blender lid is clipped into place and closed. The ring pull design allows the user to easily remove the lid with a simple leverage action.

After appliance is assembled into blender or juicer configuration, plug power cord into a 220–240V power outlet and turn on. Press the ON / OFF button to  turn the appliance on. The ON / OFF button will illuminate. The LCD timer screen will illuminate with ‘0:00’ displayed.

Functions

GETTING STARTEDThe ON / OFF button powers the unit into READY mode.PRESET PROGRAMSBLENDINGThe appliance has 5 preset functions: Smoothie, Green Smoothie, Pulse/Ice Crush, Auto Clean and Frozen Cocktail. These pre-programmed cycles automatically  adjust the blending time and speeds to optimise blending results. These programs are only activated when your appliance is in blender set up. They  can’t be used when your appliance is set up in juicing configuration. Select the required function by pressing the corresponding function button. The unit will start  to operate, and the selected function button will illuminate. The timer will start to count down and program will end automatically when it reaches ‘0:00’.  The program and timer can be paused by pressing the pause button. Resume by pressing program button again, or cancel by pressing pause again. The program  can also be canceled at any time by pressing the ON|OFF button.Turning the speed dial will interrupt the program, placing the blender in manual mode starting from Speed 1.SmoothieFor dairy-based smoothies a combination of speeds and pulses are designed to combine and aerate ingredients into a smooth and creamy texture.Green SmoothieFor blending whole fruits/vegetables into a smooth beverage. A combination of highspeed profiles breaks down tough fibres into very fine particles.Frozen CocktailFor creating ice-based cocktails and drinks like Margaritas, Daiquiris and Slushies. An ice crush program followed by a short blend.Pulse / Ice CrushA program of continuous pulsing designed to chop food into an even consistency or crush ice cubes. Use the PULSE button when the food that is being  processed is too thick or coarse to circulate within the blender jug. The pulse program can automatically detect when ice has been fully crushed and ends the  program early, indicated by a series of longer pulses.The maximum amount of ice cubes the blender can blend without liquid in the jug at any one time is 1 standard ice tray or 250g.Auto CleanUse to remove most of the ingredients off the blender walls and blades. Add 2 cups warm soapy water and press the clean button. For harder to clean, sticky or  thick ingredients, add ½ teaspoon of dishwashing detergent for extra cleaning power. For best results, clean the blender jug this way immediately after use. The  Auto Clean function only cleans the blender jug. It doesn’t clean the juicer.

MANUAL OPERATIONSpeed Control DialBlendingTurn the Speed Control Dial clockwise to select one of 10 speed settings from a slow STIR through to a very fast PULVERIZE. The timer will start to count up,  and blending will stop when it reaches ‘2:00’. Blending can be paused by pressing pause button. Press pause button again to cancel, or turn dial to resume  blending from Speed 1. To stop blending, turn the Speed Control Dial anticlockwise back to READY or press ON|OFF button.JUICINGWash your selection of fruit and vegetables to be juiced. Most fruit and vegetables such as apples, carrots and cucumbers will not need to be cut or trimmed to  size as these will fit whole into the feed chute. Ensure vegetables such as beets, carrots etc. have all soil removed, are washed well and trimmed of leaves before  using.1. Plug the power cord into your 220–240V power outlet.

IMPORTANTDo not load feed chute with produce before the Juicer has reached the selected speed.Turning the Juicer OnTurn dial to desired speed setting. Use lower numbers (1–5) for soft fruits and vegetables and higher numbers (6–10) for hard fruits and vegetables. See Speed  Selector Guide table on the next page to match speed and produce type for maximum yield. “Low” range, while it may not maximise yield of some produce,  allows you to extract juice at a significantly lower noise level.2. With the motor running, place food into the feed chute and use the food pusher to gently guide food down. To extract the maximum amount of juice, always push the food pusher down slowly.3. Full Blender Jug You can keep juicing until the jug is filled to MAX. level.

WARNINGNever use fingers, hands or utensils to push food down the feed chute or to clear the feed chute. Always use the food pusher provided.

The stainless steel filter basket contains small sharp blades to cut and process fruit and vegetables. Avoid touching the blades when handling the filter basket.

SPEED SELECTOR GUIDE

FOOD TYPE

SPEED
APPLES 10
BABY SPINACH 9
BEETROOT 10
BLUEBERRIES 5
BROCCOLI 7
CABBAGE 9
CAPSICUM 9
CARROT 10
CELERY 4
CITRUS FRUITS (peeled) 1
CUCUMBER 4
GINGER 8
GRAPES (seedless) 2
HONEYDEW MELON (peeled) 3
KALE 9
KIWI (peeled) 5
MANGO (peeled, pit removed) 5
MINT 9
PEACH (pit removed) 5
PEARS 6
PINEAPPLE (peeled) 7
RHUBARB 8
SQUASH 9
STRAWBERRIES 4
TOMATOES 4
WATERMELON (peeled) 3
ZUCCHINI 6

Care & Cleaning

Ensure the motor base is turned off by by pressing the ON / OFF button. Then unplug the power cord.

CLEANING1. Remove Blender Jug.2. Disengage Locking Bar, pull up entire Juice Collector Assembly and take to sink.3. Remove Pulp Container.Empty as much pulp as possible into bin/compost. Rinse all parts after use (except the motor base) under running water to clear away the majority of juice and  pulp. Wash in warm soapy water with a soft cloth. To avoid food drying on to the blades, mesh or transparent parts, rinse and wash as soon as possible after use.PULP CONTAINERTo minimize cleaning, you can line the pulp container with a biodegradable bag to collect the pulp.MOTOR BASEWipe down with a soft damp cloth. Do not immerse the motor base in liquids.CLEANING AGENTSDo not use abrasive scouring pads or cleaners on either the motor base or the jug, as they may scratch the surface. Use only warm soapy water with a soft clothJUG AND LIDIn order to keep your jug clean and avoid food drying on the blades and jug, follow the below steps as soon as possible after use. Rinse most of the ingredients  off the jug and lid.Fill the jug with 500ml of warm water, fit the lid and press the AUTO CLEAN button. If thick or sticky ingredients require extra cleaning power add a few drops  of dish liquid detergent.Rinse the jug and lid again and/or wash separately in warm soapy water with a soft cloth or bottle brush.It is most effective to clean the jug immediately after use.FILTER BASKETTo ensure consistent juicing results, always clean the filter basket thoroughly immediately after use, using the included brush.If pulp is left to dry, it may clog the fine pores of the filter mesh, which can affect juicing performance. The filter basket can be soaked in hot soapy water for 10  minutes, if necessary.DISHWASHERAll parts except for the motor base and food pusher are dishwasher safe. The blender jug can be placed on the bottom shelf of the dishwasher. The lid and inner  measuring cap should be washed on the top shelf only. However, washing parts on a regular basis in the dishwasher can shorten the life of them due to prolonged  exposure to harsh detergents, hot water and pressure. Cleaning the parts in the dishwasher also may cause parts to deteriorate so inspect the parts  regularly and stop using the product if any signs of damage is noticed.STUBBORN FOOD STAINSStrong smelling foods such as garlic, fish and some vegetables such as carrots may leave an odour or stain on the blender jug and lid. To remove, soak blender jug  and lid for 5 minutes in warm soapy water. Then wash with a mild detergent and warm water, rinse well and dry thoroughly. Store jug with the lid off.STORAGEStore the appliance upright with the blender jug assembled on the motor base, or beside it. Do not place anything on top. To allow air to circulate, keep the lid off. WARNINGOils in citrus rind can damage the material of your blender jug if exposed to it for a longer period. Always clean your blender jug immediately after processing citrus rind.

Troubleshooting

LCD screen turns on but  appliance doesn’t respond to controls. • The safety locking arm may not be correctly engaged in the vertical operating position. In this case,  the LCD screen will show an animated prompt. Check the top cover is properly aligned and the  locking arm is located firmly into the two grooves on either side of the juicer cover or blender jug.
Food is unevenly Chopped • This can happen when too much food is being added at one time. Try a smaller amount, and work in batches if necessary.
Food is chopped too fine or is watery • Try blending for shorter period of time. Use the PULSE function for better control
Excess pulp building up in the  stainlesssteel filter basket • Turn the appliance off. Disassemble to scoop excess pulp off the juicer cover.• Reassemble and continue juicing. Alternating soft and hard ingredients may help avoid this.
Pulp too wet and reduced extracted juice • The cleaner the filter, the better the juice yield, and dryer the pulp. Be sure to thoroughly  clean the juicer as soon as possible after each use. Remove the stainless-steel filter basket and  thoroughly clean mesh walls with a cleaning brush. Rinse the filter basket under hot water. If  the fine mesh holes are blocked, soak the basket in a solution of hot water with 10% lemon  juice to unblock the holes or wash in the dishwasher (top shelf). This will remove excess fiber  build up which could be inhibiting the flow.• Pusher force could reduce yield because it slows the motor down. Avoid putting pressure on the food pusher when pushing ingredients down the feed chute.• If juicing large amounts of fibrous ingredients like rhubarb and pineapple, cleaning the filter basket in between might be required.
Juice leaks between the filter bowl  surround and the juicer cover • Try a slower juicing speed and push the food pusher down the feed chute more slowly.• Ensure there is no build up in the filter basket.
Juice sprays out from spout • The juice is being extracted too fast; try a slower juicing speed (if possible) and push the food pusher down the feed chute more slowly.
Juice in filter bowl is left after juicer stopped • Turn the speed dial up to highest speed setting and operate for 5 seconds. That can help moving the remaining juice into the jug.
Motor appears to stall during juicing • Wet pulp can build up under the juicer cover and stall the appliance if the appliance is used  excessively without cleaning. If this occurs, disassemble and follow the cleaning instructions  to clean the filter bowl surround, the stainlesssteel filter basket and the juicer cover. The  appliance can also stall if excessive force is used to push produce down the feed chute. If this occurs, ensure that a gentler pressure is used to push produce down the chute.• Turn on the appliance before putting ingredients in the chute. Pressing ingredients down  before the motor reaches full speed can cause it to stall or overload. Use gentle to moderate  pressure on the pusher. Lower pressure produces a better juice yield.• Hard fruit and vegetables will put excess strain onto the motor if a low speed is selected.  Refer to the reference guide to determine the correct speed for the fruit and vegetables selected for juicing.
All control panel lights flash and  Overload Protection displayed on LCD screen • This indicates motor overload protection is activated due to motor overheating or stalling.• To reset the protector, unplug from the power supply, then plug back in and turn on.• If overload protection is still displayed, unplug the appliance and leave to cool for at least 30  minutes, then try again. The appliance must be unplugged while cooling in order to reset  properly.• If the issue persists after allowing to cool, this indicates an internal problem. Please call  Breville Customer Service or your nearest Authorised Breville Service Centre.• Note that triggering the overload protection indicates abnormal use of the appliance, such  as too much load in the blender jug, excessive push force when juicing or extended  continuous use. Please take note of the conditions and refer to all of the information in these  instructions to avoid this occurrence and extend the life of the appliance.

Breville Customer Service CentreAustralian CustomersPhone: 1300 139 798Web: www.breville.com.auNew Zealand CustomersPhone: 0800 273 845Web: www.breville.co.nz

Breville, the Breville logo and the Twin Turbo Pro are registered trademarks of Breville Pty. Ltd. A.B.N. 98 000 092 928.Copyright Breville Pty. Ltd. 2019.Due to continued product improvement, the products illustrated/photographed in this brochure may vary slightly from the actual product.BJB815 ANZ – A19

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,