BROADCOM Emulex Drivers for Windows Installation Guide

Emulex® Drivers for Windows

Quick Installation GuideRelease 12.8

Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, the A logo, Emulex, OneCommand, and OneConnect are among the trademarks of Broadcom and/or its affiliates in the United States, certain other countries, and/ or the EU.

Copyright © 2003–2020 Broadcom. All Rights Reserved.

The term “Broadcom” refers to Broadcom Inc. and/or its subsidiaries. For more information, please visit www.broadcom.com.

Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does not assume any liability arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others.

Chapter 1: Introduction

This product supports the following Emulex® adapters:

  • LPe12000-series adapters
  • LPe16000-series adapters
  • LPe31000-series adapters
  • LPe32000-series adapters
  • LPe35000-series adapters

Chapter 2: Installation

NOTE: The Emulex OneCommand® Manager application has been renamed as the Emulex HBA Manager application.

Emulex drivers for Windows are available in two types of packages:

  • The OneInstall driver and application kit contains the Emulex Storport Miniport driver and the Emulex HBA Manager application in a single download package.
  • The driver kit, which includes the AutoPilot Installer, provides installation options ranging from simple installations with a few mouse clicks to unattended installations that use predefined script files and text-only installations.

NOTE: Check www.broadcom.com for required updates to the Windows operating system or the Emulex drivers.

2.1 Using the OneInstall Kit

You can run the OneInstall kit in Interactive mode or Silent mode.

NOTE: The OneInstall kit does not allow you to perform preinstallation tasks or text-only installations. For these tasks, use the driver kits.

The OneInstall kit is a self-extracting executable file that installs the following software on your system:

  • FC driver
  • Emulex HBA Manager application

NOTE: The enterprise kit for the Emulex HBA Manager application does not operate locally on the Windows Server Core. You must install the Emulex HBA Manager application core kit CLI only on the Windows Server Core. Refer to the Emulex HBA Manager Application User Guide for installation instructions.

2.1.1 Loading the OneInstall Kit Using Interactive Mode

To install the drivers and the Emulex HBA Manager application using Interactive mode, perform the following steps:

  1. Download the OneInstall kit from the Broadcom website to a directory on your system.
  2. Navigate to the OneInstall kit Installer in Windows Explorer.
  3. Double-click OneInstall file to run it.The Welcome dialog is displayed.
  4. Click Next.The Installation Options dialog is displayed.
  5. Select the drivers and applications that you want to install and click Next.A progress screen is displayed while OneInstall loads the selected drivers and applications. After the drivers and application software are loaded, an Installation completed screen is displayed.
  6. Click Finish.
2.1.2 Loading the OneInstall Kit Using Silent Mode

You can perform a Silent mode installation from a batch file or from the command line.

If you run OneInstall from a batch file or from a command line prompt, the default Windows behavior starts OneInstall and then immediately continues with the next command. As a result, the value of %ERRORLEVEL% will always be 0 because Windows successfully started OneInstall Installer. It does not reflect an accurate OneInstall Installer exit code.

To remedy this problem, run the OneInstall setup as follows:START /wait OneInstall-Setup-<version>.exeecho %ERRORLEVEL%

The START /wait entry ensures that the command prompt does not return until setup has exited. The value of %ERRORLEVEL% now accurately reflects the OneInstall exit code.

2.1.2.1 Command Syntax

The following is the installation command syntax:OneInstall-Setup-<version>.exe <install-mode> <options>

Where:

<version> is the version number of the OneInstall kit.

<install-mode> is one of the following:/q0 – (Interactive, non silent install) This is the default./q1 – (Non interactive install) This option displays status pages./q2 – (Silent install) This option is completely silent; no pages are displayed./q – This is the same as /q1.

<options> specify the kit, or kits, to install:ALL=1 – Installs the FC driver and the Emulex HBA Manager application (default).

NOTE: On a Windows Server Core system, this option installs all drivers and the Emulex HBA Manager application core kit.

ALLCORE=1 – Installs the FC driver and the Emulex HBA Manager application core kit.FC=1 – Installs the FC driver only.OCM=1 – Installs the Emulex HBA Manager application.

NOTE: On a Windows Server Core system, this option installs the Emulex HBA Manager application core kit.OCMORE=1 – Installs the Emulex HBA Manager application core kit only.

To install the drivers, applications, or both using Silent mode, perform the following steps:

  1. Download the OneInstall kit from the Broadcom to a directory on your system.
  2. Open a DOS window.
  3. Navigate to the directory that contains the OneInstall kit.
  4. Type the installation command on the command line, and press Enter.

The following are examples of Silent mode commands:Start /wait OneInstall-Setup-<version>.exe /q2 ALL=1Start /wait OneInstall-Setup-<version>.exe /q2 FC=1Start /wait OneInstall-Setup-<version>.exe /q2 OCM=1Start /wait OneInstall-Setup-<version>.exe /q2 ALLCORE=1Start /wait OneInstall-Setup-<version>.exe /q2 OCMCORE=1

2.2 Loading the Driver Kit

The driver kit unpacks the selected Emulex drivers and applications onto your computer.

NOTE: This procedure does not install the drivers, and no driver changes are made until you run the AutoPilot Installer application.

To load the driver kit, perform the following steps:

  1. Download the driver kit from the Broadcom website to a directory on your system.
  2. Navigate to the driver kit in Windows Explorer.
  3. Double-click the driver kit file to run it.The Emulex Kit Welcome page is displayed.
  4. Click Next.The Installation Options window is displayed.
  5. Select one or both of the following options:– Perform Installation of Software – Copies the driver kit for your operating system to your computer.– Unpack All Drivers – Extracts all drivers to the current user’s Documents folder. Select this option to perform boot from SAN installations.The Operation in progress window displays the file-loading progress of the kit. After the kit files are loaded, the Installation completed window is displayed.
  6. To continue with the installation, ensure that Start AutoPilot Installer is selected.
2.3 AutoPilot Installer

AutoPilot Installer runs after the driver kit is loaded and the Emulex HBA Manager application is installed. AutoPilot Installer can be installed at the following times:

  • Immediately after the driver kit has been loaded
  • At a later time using an interactive installation
  • Through an unattended installation

AutoPilot Installer provides the following functions:

  • Command line functionality – Initiates an installation from a command prompt or script. Configuration settings can be specified in the command line.
  • Compatibility verification – Verifies that the driver to be installed is compatible with the operating system and platform.
  • Driver installation and update – Installs and updates drivers.
  • Multiple adapter installation capability – Installs drivers on multiple adapters, alleviating the requirement to manually install the same driver on all adapters in the system.

NOTE: Refer to the Emulex Software Kit Migration User Guide for information about installing drivers on a system that contains a mix of OneConnect® adapters and FC HBAs.

  • Driver diagnostics – Determines whether the driver is operating properly.
  • Silent installation mode – Suppresses all screen output (necessary for unattended installation).

NOTE: AutoPilot Installer does not allow you to install the driver if the minimum Windows service pack or Microsoft Storport driver update is not installed.

You can install the driver by using any of the following methods.

NOTE: These installation methods are not mutually exclusive.

  • Hardware-first installation. At least one Emulex adapter must be installed before you can install the Emulex drivers and utilities.
  • Software-first installation. You can install drivers and utilities using AutoPilot Installer prior to the installation of any adapters. You do not need to specify the adapter models to be installed later. The appropriate drivers and utilities automatically load when you install the adapters.
  • Utility-only installation. If the drivers in the driver kit share the same version with those already installed on the system, you can reinstall or update the previously installed utility without reinstalling the drivers.
  • Text-only installation. Text-based installation mode is used automatically when AutoPilot Installer is run on a Windows Server Core system.
  • Network installation. You can place the driver kit installers on a shared network drive and install them across your LAN. Network-based installation is often used with unattended installation and scripting, which allows you to configure and install the same driver and utility versions on all the hosts in a SAN.

NOTE: Unattended installation. You can run the driver kit installers and AutoPilot Installer with no user interaction from a command line or script. Unattended installation works for both hardware-first and software-first installations and all driver kits. An unattended installation operates in Silent mode (also referred to as Quiet mode) and creates an extensive report file with installation status.

2.3.1 Starting Installers from a Command Prompt or Script

If a driver kit or AutoPilot Installer is run from a command prompt or command script (batch file), the Windows command processor does not wait for the installer to run to completion. As a result, you cannot check the exit code of the installer before the next command is executed. For command line invocation, always use the START command with the /wait option, which causes the command processor to wait for the installer to finish before the command processor continues.

For additional information on command line installation and configuration parameters, see the Emulex® Drivers for Windows User Guide.

2.3.2 Running a Software Installation Interactively

Two options are available when performing an installation interactively. These options assume that you have already downloaded the driver kit from the Broadcom website.

  • Option 1 allows you to automatically run AutoPilot Installer, which completes the driver kit loading and installation with a few mouse clicks.
  • Option 2 allows you to run AutoPilot Installer separately. Use this option to perform the following actions:– Change installation settings for a limited number of systems.– Familiarize yourself with AutoPilot Installer configuration options.

2.3.2.1 Option 1: Automatically Run AutoPilot Installer

Use this option unless you have specific configuration requirements.

  1. Double-click the driver kit or run it from a command line. The command line parameter APargs allows you to specify arguments that are automatically passed to the AutoPilot Installer command.A Welcome window is displayed with driver kit version information and Emulex contact information (refer to the Emulex Drivers for Windows User Guide for additional information on command line installations).
  2. Click Next to proceed to the Installation Options window.For each installation option, the default installation location for that option is displayed. Browse to a different location, if desired.
  3. Click Install to continue the installation.The Progress dialog is displayed.After all tasks are completed, a Finish window is displayed. Start AutoPilot Installer is automatically selected.
  4. Click Finish.AutoPilot Installer runs automatically and completes one of the following installations:– Section 2.3.3, Hardware-First Installation or Driver Update– Section 2.3.4, Software-First Installation

2.3.2.2 Option 2: Run AutoPilot Installer Separately

Run AutoPilot Installer after the driver kit is finished loading, which allows you to change the configuration options supplied to AutoPilot Installer.

  1. Perform Step 1 through Step 3 in Option 1: Automatically Run AutoPilot Installer.
  2. Clear Run AutoPilot Installer in the Finish dialog.
  3. Click Finish.The driver kit installer exits.After the driver kit loading is complete, change the configuration in one of two ways:– Change the configuration file.– Supply parameters on the command line.NOTE: Refer to the Emulex Drivers for Windows User Guide for additional information on either of these configuration methods.After you have finished this step, you can run AutoPilot Installer at a later time.
  4. Run AutoPilot Installer using the following command:C:\Program Files\Emulex\AutoPilot Installer\APInstall.exe

NOTE: The location of APInstall.exe might differ on your system, depending on your system’s Program Files location. You can also specify a different location when you install the driver package.

2.3.3 Hardware-First Installation or Driver Update

The driver kit installer must be downloaded from the Broadcom website and installed before performing this installation.

NOTE: To update an Emulex protocol driver, begin this procedure at Step 2.

To perform a hardware-first installation, perform the following steps:

  1. Install a new Emulex adapter and power on the system. If the Windows Found New Hardware wizard is displayed, click Cancel to exit; AutoPilot Installer performs this function.NOTE: If multiple adapters are in the system, the Windows Found New Hardware wizard is displayed multiple times. Click Cancel to exit the wizard each time it is displayed.
  2. Run AutoPilot Installer using one of the two options listed in Section 2.3.2, Running a Software Installation Interactively.Consider the following:– If you are updating the driver, the existing port settings are used unless otherwise specified in the configuration file.These settings are preselected but they can be changed. Set or change the settings, and then click Next.– If you are initially installing a vendor-specific version of the Emulex driver installation program, a Driver Configuration window might be displayed. This window includes one or more windows with questions that you must answer before continuing the installation process. In this case, answer each question and click Next on each window to continue.
  3. Click Next. The installation is completed automatically.A dialog is displayed if Windows requires a reboot. After the installation is successful, a Finish window is displayed.
  4. View or print a report, if desired.– View Installation Report – The installation report is a text file with current Emulex adapter inventory, configuration information, and task results.– Print Installation Report – The Windows Print dialog is displayed to select options for printing the installation report.
  5. Click Finish to exit AutoPilot Installer.
  6. If the system must be rebooted, you are prompted to do so. You must reboot before using the drivers or utilities.
2.3.4 Software-First Installation

The driver kit must be downloaded from the Broadcom website and loaded.To do a software-first installation, perform the following steps:

1. Run AutoPilot Installer using one of the two options listed in Section 2.3.2, Running a Software Installation Interactively. Figure 1 is displayed.

Figure 1: AutoPilot Installer Popup (Software-First Installation)

2. Click OK.A Welcome window is displayed.3. Click Next. The installation automatically progresses.After the installation is successful, the Finish window is displayed.4. View or print a report, if desired.– View Installation Report – The installation report is a text file with the current Emulex adapter inventory, configuration information, and task results.– Print Installation Report – The Windows Print dialog is displayed to select options for printing the installation report.5. Click Finish to exit AutoPilot Installer.

2.3.5 Text-Only Driver Installation

Text-based installation mode is used automatically when the driver kit installer runs on a server with the Server Core installation option of Windows Server. During text-based installations, AutoPilot Installer uses a command prompt window. The driver kit installer notifies you when the driver is installed and also gives you an opportunity to stop the installation.

Whether AutoPilot Installer is launched from the command line or run as a program, Windows always starts AutoPilot Installer as a separate stand-alone task. This means that AutoPilot Installer has its own command prompt window and cannot access other windows.

Chapter 3: Installation Failure

The two possible installation failures are described in this chapter.

3.1 AutoPilot Installer Failure

If AutoPilot Installer fails, the Diagnostics window displays a message indicating that the adapter failed. If the adapter fails, perform the following steps:

  1. Select the adapter to view the reason why the adapter failed. The reason and suggested corrective action are displayed.
  2. Perform the suggested corrective action, and run AutoPilot Installer again.

NOTE: You can run APInstall.exe from a command prompt.

3.2 OneInstall Failure

OneInstall might fail for any of the following reasons:

  • The operating system prerequisites have not been met.
  • The individual kit installation failed. To check the installation, run the installation interactively. If you encounter error messages when you run the installation interactively, those issues would also apply to an unattended installation.
  • If an individual package failed to install properly, run that package’s installer directly. This method displays status and error messages that can be used to diagnose the issue. (OneInstall does not provide this information because each package is installed silently.)

 

report this ad

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,