BUFFALO CY141 Blender Instruction Manual

BlenderInstruction manual

Model: CY140 / CY141

Safety Tips

• Position on a flat, stable surface.
• A service agent/qualified technician should carry out installation and any repairs if required. Do not remove any components on this product.
• Consult Local and National Standards to comply with the following:– Health and Safety at Work Legislation– BS EN Codes of Practice– Fire Precautions– IEE Wiring Regulations– Building Regulations
• DO NOT use jet/pressure washers to clean the appliance.
• DO NOT immerse the appliance in water.
• This appliance is only used for blending food. Do not use the appliance for anything other than its intended use.
• Always switch off and disconnect the power supply to the appliance when not in use.
• Not suitable for outdoor use.
• Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of local authorities.
• If the power cord is damaged, it must be replaced by an BUFFALO agent or a recommended qualified technician in order to avoid a hazard.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not let cord hang over edge of table or counter, or touch hot surfaces.
• Keep hands and utensils out of the jug while motor is running to prevent severe personal injury and/or damage to the blender.
• Blade is sharp – handle carefully.
• Never try to remove blade while jug is sitting on the blender base.
• Do not operate with loose or damaged blades.
• Always operate with lid in place.
• Do Not blend Hot Liquids.
• Do not leave blender unattended while in use.
• Buffalo recommends that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to: Visual Inspection, Polarity Test, Earth Continuity, Insulation Continuity and Functional Testing.
• Buffalo recommend that this product is connected to a circuit protected by an appropriate RCD (ResidualCurrent Device).

Introduction

Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your BUFFALO product.

Product Description

• CY140 – Buffalo Blender with Touch Control – 2.5Ltr Jug
• CY141 – Buffalo Blender with Touch Control -2.5Ltr Jug – with Sound Enclosure

Pack Contents

The following is included:

• BUFFALO Blender
• Blender Jug, lid and lid plug
• Food pusher
•  Instruction manualBUFFALO prides itself on quality and service, ensuring that at the time of packaging the contents are supplied fully functional and free of damage.Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately.

Operation

Blending

Before use, ensure to:

• Disconnect the blender from power supply.
• Clean all removable parts thoroughly.

1. Plug in Blender.
2. Place ingredients into jug.
3. Secure the lid and lid plug (Note: Always operate with the lid secured).
4. Locate jug on to body of blender. The On/Off key lights up.
5. Press the On/Off key to enter standby. Press again to start blending with the default speed setting (2).
6. Pulse function: Press and hold the Pulse key to start. Release to stop.
7. After use, press the On/Off key to switch off blender.

Using the timer functionIf to use the timer function during use:

1. Press the desired time key. Then press the speed key or On/Off key.
2. The blender starts while the timer counts down on the display.
3. When the set time expires, the blender switches off automatically.• During use, your can press the time/speed key to pause operation. Press again to continue.

Note:• When blending dry ingredients best results will be obtained by cutting ingredients into small pieces and adding to the blender through the hole in the lid when motor is running.• Before removing jug, ensure to turn off blender using On/Off switch and let the motor come to a complete stop.

Cleaning, Care & Maintenance

• Always disconnect from power supply before cleaning.• Always allow to cool before cleaning.• Let the motor come to a complete stop before removing the jug.• The jug is NOT dishwasher proof!• Use warm, soapy water and a damp cloth to clean the jug.

Warning: Blade is sharp – handle with care.• Dry thoroughly after cleaning.• A BUFFALO dealer or qualified technician should carry out repairs if required.

Warning: Do not allow any water to spill into the body of the appliance when cleaning.

Troubleshooting

Fault	Probable Cause	Solution
The unit is not working	The unit is not switched on	Check the unit is plugged in correctly and switched on
Plug and lead are damaged	Call BUFFALO agent or qualified Technician
Fuse in the plug has blown	Replace the plug fuse
Power supply	Check power supply
Internal wiring fault	Call BUFFALO agent or qualified technician
Jug incorrectly located on body of appliance	Relocate Jug

Technical Specifications

Model	Voltage	Power	Current	Jug Capacity	Dimensionsh x w x d mm	Weight
CY140	220-240V50/60Hz	1680W	8A	2.5L	535 x 236 x 253	6kg
CY141	220-240V50/60Hz	1680W	8A	2.5L	547 x 236 x 253	9kg

Electrical Wiring

This appliance is supplied with a 3 pin BS1363 plug and lead.The plug is to be connected to a suitable mains socket.This appliance is wired as follows:

• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E

This appliance must be earthed.If in doubt consult a qualified electrician.Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible.

Compliance

The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.

BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities.

BUFFALO products have been approved to carry the following symbol:

All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of BUFFALO. Every effort is made to ensure all details are correct at the time of going to press, however, BUFFALO reserve the right to change specifications without notice.

DECLARATION OF CONFORMITY

• Conformiteitsverklaring

Equipment Type	Model
Blender with touch control – 2.5Ltr JugBlender with touch control – 2.5Ltr Jug – with Sound Enclosure	CY140 (& -E)CY141 (& -E)
Application of Territory Legislation & Council Directives(s)	Machinery Directive 2006/42/EC60204-1:201812852:2001 +A1:2010ISO 12100:2010Electro-Magnetic Compatibility (EMC) Directive 2014/30/EU – recast of 2004/108/EC 55014-1: 201755014-2: 201561000-3-2: 201461000-3-3: 2013   Restriction of Hazardous Substances Directive (RoHS) 2015/863 amending Annex II to Directive 2011/65/EU
Producer Name	Buffalo

I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s) and Standard(s).

Date	30th October 2020
Signature
Full Name	Ashley Hooper	Eoghan Donnellan
Position	Technical & Quality Manager	Commercial Manager/ Importer
Producer Address	Fourth Way,Avonmouth,Bristol,BS11 8TBUnited Kingdom	42 North Point Business ParkNew Mallow RoadCorkIreland

UK	+44 (0)845 146 2887
Eire
NL	040 – 2628080
FR	01 60 34 28 80
BE-NL	0800-29129
BE-FR	0800-29229
DE	0800 – 1860806
IT	N/A
ES	901-100 133
PT	[email protected]

http://www.buffalo-appliances.com/

References

• 
  Buffalo Home Page