CALIBER CAM401 Wireless Reverse Video Camera User Manual
Precautions
Points to observe for safe usageRead this manual carefully before using this item and its components. They contain instructions on how to use this prod-uct in a safe and effective manner. Caliber Europe BV cannot be responsible for problems resulting from failure to observe the instructions in this manual.
Turn off the device immediately in case of a problem.Failure to do so may cause personal injury or damage to the product. Return it to your authorized Caliber Europe BV dealer for repairing.
Product cleaning.Use a soft dry cloth for periodic cleaning of the product. For more severe stains, please dampen the cloth with water only. Anything else has the chance of dissolving the paint or damaging the plastic.
Temperature.Be sure the temperature inside the room is between +35°C (+95°F) and -10°C (+14°F) before turning your unit on.
Maintenance.If you have problems, do not attempt to repair the unit yourself. Return it to your Caliber Europe BV dealer for servicing.
Placement.Place the product on a flat surface. Provide enough space around the product for sufficient ventilation.
Heat.Do not locate the appliance in the vicinity of a heat surface or in direct sunlight.
Accessories.Use only supplied accessories.
- +12-24V DC inUse the provided cigarette lighter plug adapter.
- Display4.3″ LED TFT color display
- Indication LED
- Flashing: searching for camera
- Solid ON: camera connected
- Menu button
- Open/exit the adjustment menu.
- Functions as a “one step back” button in the menu.
- Move cursor to the left in the menu.
- Choose between camera 1 and 2.
- Turn the monitor ON/OFF
- Enter/confirm menu selection
Move cursor to the right in the menu.
- Guideline buttonTurn ON/OFF the on screen guidelines.
Installation
MonitorThe monitor comes with a suction cup bracket and a 12-24V cigarette lighter plug adapter.
How to use the bracket, please see the instructions on the second page of this manual.
To power the monitor, please only use the provided cigarette lighter plug in order to prevent damage to the equipment. Place the cigarette lighter plug into a 12-24V outlet in your vehicle. Plug the other end into the DC-in of the monitor, indicated with no. 1 in the drawing above.
CameraBecause this system can be used for many purposes, not all instructions may be applicable to the installation in your situation. Try to follow the guidelines as good as possible. If you can’t figure it out, we advise you to contact an installation expert.
Placement:On the back of the camera there is a bracket that is equipped with professional double-sided tape for secure mounting.
Please note or whether the surface is suitable and if you won’t damage anything behind or inside while using screws.
The camera is tilt able so the angle be adjusted manually in a vertical direction. Make sure its field of view and direction are not obstructed.
Powering the cameraMake sure the power connection is inside the vehicle, in a dry and safe location. Often it is possible to get the wire inside the vehicle using an existing passageway, for example; near the number plate lights or the trailer hitch wiring harness.
If there is no existing passageway available, you must drill a hole. Make sure you can’t damage anything behind or inside the location you want the drill the hole. Using a drilled hole, always use the provided grommet to prevent any sharp edged cutting into the camera cable.
The camera should only be powered if its in use, a common connection is via the reversing light of the vehicle. This situation will be explained below. But of course it is also possible to make a connection via the key or a separate switch.
- Connect the red wire of the camera to the +12V/+24V
wire of the vehicles reverse light, using the provided in-line wire connectors.
- Connect the black wire of the camera to the ground cable the vehicles reverse light, using the provided in-line wire connectors or to a a safe alternative ground point.
There is no need to make a wired connection between the camera and the monitor. This will be a wireless video signal with a range up to 50m. If the monitor does not find the camera, see the “Setup (pair) menu” under operation.
ExtraThe monitor can be connected with max. two cameras. An extra camera is sold separately (CAM401E). For the installation of the extra camera, please use the same guide steps as for the first camera.
Operating
MenuPress the menu button (4) on the monitor to enter the menu. The following icons will be shown and below you’ll find the explanation of their operation per icon. To enter/ choose a selection use the (0) button. To go back in the menu step-by-step, use the menu button (4). To scroll through the menu you can use the [4•/vj buttons (5/7).
Adjustment menuThe first step is to choose the camera that you want to adjust. After your selection you can adjust the brigh ness, contrast and color. Use the
buttons (5/7) to adjust and the menu button (4) to go back.
Rotation menuThe first step is to choose the camera that you want to adjust. After your selection you can rotate and mirro the camera image within 4 steps using the RN button. Use the menu button (4) to go back.
Setup (pair) menuAfter entering the pairing menu you can choose CAM 1 and CAM 2. Choose CAM 1 to start pairing with he supplied camera (push and hold the button on the bottom side of the camera). If you have purchased the additional extra camera (CAM401 E), you can connect this camera as CAM 2 using this menu.
With the icon that says “master, you can choose between camera 1 and 2 as your “master” camera. This will be the one shown automatically when the monitor is turned ON.
Switching between the views of the cameras can easily be done with the (s) button (5). The number of the camera that is shown can be seen in top of the screen (C1/C2). Note: Make sure you’re not in the menu.
Information menuThis shows you the software-version of the monitor system.
[xyz-ips snippet=”download-snippet”]