Comfort Stand Fan CF-16WB Instruction Manual

Comfort Stand Fan CF-16WB Instruction Manual

Safety instruction

1. Never put your finger or other something into the cover to avoid any hurts.
2. Make sure to keep the fan far away from humidity, chemical articles and oil.
3. While cleaning, be sure to not splash water and do not use oil, alcohol or chemical articles as they may cause distortion of fan body and cause electrical hazards.
4. Do not pull out the power supply plug by pulling power supply cord, which may lead to electrical shock or generating electrical shock_
5. Keep away from curtain, clothing or other something may affect the fan’s working.
6. Thin off all switches and pull out power supply plug when you go out for long time.
7. Never use the fan before finishing assembly to avoid any hurts.
8. If  the supply cord is damaged, it must be repaired by the manufacture of its service agent or a similarly qualified in order to avoid a hazard.
9. Before sending for maintaining, if the unit doesn’t work please check the plug of power supply has been inserted into socket with electricity.
10. Do not use the electric fan m rain.

What is included

1. shroud ring &fastener for cover
2. front cover
3. fastener for fan blade
4. fan blade
5. fastner for cover
6. back cover
7. output shaft
8. joint
9. back pane
10. decorative cover
11. up-down tube
12. external joint
13.  support tube
14.  decorative cover 
15. head rotating button

Installing and using

Pint step: Assemble and connect the base with assembly up-down tube and support tube. Open the casing and take out base. Then assemble the tube and cover of up-down tube and support tube Aim the four holes on the bottom of support tube of support at the boles on the  base and tighten the screws. Slip decorative cover to base alongside the support tube and adjust up-down tube to height Then rotate tighten the external joint.Second step: Assemble fan blade

1. Assemble guard cover and shroud ringTighten back cover enclosure to the motor by fastener. (Pay attention to direction of rotation). Place joint of shroud ring downwards and cover the deep groove of shroud ring to the circle side ring of back cover enclosure. Then tighten the bolts at the position of joint properly by nut.
2. Install fan bladeWhile installing fan blade, please wedge groove on the back of fan blade on spacer pin of the output shaft of motor. Then tighten the fixing nut of fan blade anticlockwise.
3. Assemble front coverInsert the circle of front cover into the groove of shroud ring, which has been fixed to the back cover. Finally fasten the bolts into screw of the joint of shroud ring.

Direction of use

1. Setting of wind direction This fan can swing in up and down direction. The angle of facing upwards and downwards can be adjusted by slightly lift or press the cover.
2. Setting of shaking Press the turning button and the head starts to rotate. Then pull it out and fan will stop rotating.
3. Setting of wind speed and wind type Pressing button of wind speed can adjust the speed of wind.

Solution to simple failure

When starting the fan, the fan blade doesn’t work. Please check whether the power plug has really inserted into the socket or the cover has distorted, which has touched the fan blade. If sound the noise when starting the fan, please check the unit as follows:

1. Fan blade has been tight installed into the output shaft of motor.
2. Groove on back of cover has matched the inserting groove on the output shaft
3. There arc tiny defective edge ring existing around the fan blade.
4. The cover has distorted, which has touched the fan blade.

Maintaining

Be sure to switch off the power supply and pull out the plug before cleaning.

1. This machine only needs common external cleaning and wiping.
2. Place into casing and store in the dry position.

Technical parameters

PLEASE FILL YOUR DETAILS FOR FUTURE USE

GURANTEE CARD

CUSTOMER’SNAME OF BUYER_________________________________________ADDRESS________________________________________________TELEPHONE_____________________________________________

DETA:LS OF SHOPNAME OF SHOP__________________________________________RECEIPT VOUCHER NO.___________________________________DATE OF PURCHASE______________________________________

APPL5ANCE DETAILSTYPE OF APPLIANCE_____________________________________MODEL NO.______________________________________________SERIAL NO.______________________________________________