iCUEH100i | H150i | H170iELITE LCDEXTREME PERFORMANCE LCD LIQUID CPU COOLER
Note: Most newer PC cases include a CPU cut-out to allow access to the bottom of the motherboard. If your case does not include a cut-out, you will need to remove your motherboard from the case prior to installation. RGB Series coolers come with the Intel mounting bracket pre-installed on the pump for quick installation.
INCLUDED HARDWARE
Highlighted parts for Intel installation only
1. Installing the Intel Backplate
NOTE: Intel LGA 2011/2011-3/2066 do not require backplate installation.Proceed to step 2.2. Installing the Intel Standoff Screws
> Attach the provided Intel standoff for your socket.> Use (A) for LGA 1200/115X, (B) for LGA 2011/ 2011-3/2066 or (C) for LGA1700.> Tighten all four screws until firmly secured.3. Install the Fans and Radiator
Attach the radiator and the fans as shown. For the best cooling performance, we recommend mounting the fans as an air-intake to your PC case.4. Installing the Pump Unit
> Align the bracket and pump over the standoff screws as shown.> Attach the thumbscrews (F) to the standoff screws as shown.> Tighten the thumbscrews until all four corners are firmly secured.Highlighted parts for AMD installation only
1. Installing the AMD (AM4) Mounting Bracket
> Remove the integrated Intel mounting bracket (figure 1).> Install the AMD bracket by pushing both sides into the slot on the pump until secure (figure 2).Note: It is important that the AMD retention bracket be evenly secured on all sides before installation.2. Install the Fans and Radiator
Attach the radiator and the fans as shown. For the best cooling performance, we recommend mounting the fans as an air-intake to your PC case.3. Prepare The Motherboard For Installation
Remove the existing AMD mounting brackets shown.4. Installing the AMD AM4 Standoff Screws
> Attach the provided AMD AM4 standoffs to the CPU socket.> Tighten all four screws until firmly secure.5. Install the Pump Unit
Align the bracket with the stock AMD mounting clips as shown. Tighten the thumbscrews until secure.Highlighted parts for AMD sTRX4 installation only
1. Installing the AMD sTRX4 Mounting Bracket
> Remove the integrated Intel mounting bracket (figure 1).> Install the AMD sTRX4 brake by pushing both sides into the slot on the pump until secure(figure 2).Note: It is important that the AMD sTRX4 retention bracket be evenly secured on all sides before installation.2. Installing the AMD sTRX4 Standoff Screws
> Attach the provided AMD sTRX4 standoffs to the CPU socket.> Tighten all four screws until firmly secure.3. Install the Fans and Radiator
Attach the radiator and the fans as shown. For the best cooling performance, we recommend mounting the fans as an air-intake to your PC case.4. Installing the Pump Unit
> Align the bracket and pump over the standoff screws as shown.> Attach the thumbscrews (F) to the standoff screws as shown.> Tighten the thumbscrews until all four corners are firmly secured.
Connect Fans and Pump to Commander Core> Connect pump 24-pin cable to your Commander CORE (figure 1).> Connect pump tach cable to the CPU_FAN header on your motherboard (figure 2).> Connect each fan to the Commander CORE (figure 3).> Connect each fan RGB lead to the Commander CORE (figure 3).
Connect Commander Core and Elite LCD Module to USB 2.0 Header and Power> Using the attached USB cable, connect the Commander Core to a motherboard USB 2.0 header.> Connect the pump power cable to an available SATA power plug from your power supply.
FAQ
- How do I know the direction of the airflow of the fan?An arrow located on the side of the fan indicates the direction of airflow.
- Can I reuse the pre-applied thermal paste on the cooler for re-installation?Re-installation of the cooler will require you to clean off the pre-applied thermal paste and apply an aftermarket paste.
- What orientation should I install my radiator?The best way to install a radiator is with the tubes on the bottom of the case, though you can install it with the tubes in any position, including an inverted radiator, as long as the highest point in the radiator is visibly higher than the CPU pump.
- My cooler and fans are blinking red or not functioning. What do I do?Please double-check all connections from the cooler and fans to the Commander CORE. Ensure that the Commander CORE and LCD module are updated to the most recent firmware via iCUE. If this does not resolve your problems, please open a ticket at support.corsair.com or contact our customer support team for further troubleshooting and assistance.https://help.corsair.com/hc/en-us/requests/new
Web: corsair.comPhone: (888) 222-4346Warranty: corsair.com/support/warrantySupport: support.corsair.comBlog: corsair.com/blogForum: forum.corsair.comYouTube: youtube.com/corsairhowto© 2021 CORSAIR MEMORY, Inc. All rights reserved. CORSAIR and the sails logo are registered trademarks of CORSAIR in the United States and/or other countries. All other trademarks are the property of their respective owners. Product may vary slightly from those pictured.49-002477 AA
References
[xyz-ips snippet=”download-snippet”]