Cuisinart Woodcreek 4-in-1 Pellet Grill [SMK0036AS, SMK0036ASO] Instruction Manual

Woodcreek4-in-1 Pellet GrillASSEMBLY INSTRUCTIONSModel SMK0036AS / SMK0036ASO

ASSEMBLY INSTRUCTIONS:READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR GRILL.

WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.The following tools are required to assemble this Cuisinart Woodcreek 4-in-1 Pellet Grill:

•  Phillips Screwdriver
•  Pliers or Wrench

Note: Most hardware is per-attached to the grill. You may need to loosen some screws partially while others may need to be removed in order to assemble parts. The screws that you remove will be re-used so don’t misplace this hardware.Extra screws are included in a small bag with the owners manual.

Step 1

• Remove 2 screws• Attach FRONT PANELS 1 and 2• Tighten 2 screws

Step 2

• Loosen 6 screws 3-4 turns on FRONT LEGS 3 and 4• Do not remove screws• Attach FRONT PANELS 1 and 2 using keyholes• Tighten 6 screws

Step 3

• Loosen 3 screws• Attach RIGHT SIDE PANEL 5• Tighten 3 screws on RIGHT SIDE PANEL 5

Step 4

• Loosen 2 screws• Attach LEFT SIDE PANEL 6• Tighten 2 screws on LEFT SIDE PANEL 6

Step 5

• Loosen 2 screws• Attach CART BRACE 7• Tighten 2 screws on CART BRACE 7• Remove 4 screws

Step 6

• Attach CART BASE 8• Tighten 4 screws (Removed from Step 5)

Step 7

• Loosen 8 screws on REAR LEGS 9 and 11• Attach BACK PANEL 10 to REAR LEGS 9 and  11• Tighten 4 screws• Remove 4 screws

Step 8

• Attach CART BASE 8 to rear legs• Tighten 4 screws (Removed from Step 7)

Step 9

• Attach LEFT SIDE PANEL 6 and CART BRACE  7• Tighten 4 screws

Step 10

• Lock CASTERS 37• Attach CASTERS 37 to legs

Step 11

• Attach ACCESSORY HOOKS 33 to LEFT SIDE PANEL 6 and CART BRACE 7 with wing nuts

Step 12

• Loosen 1 screw• Remove 2 screws

 

Step 13

• Loosen 5 screws• Remove 2 screws

Step 14

• Set GRILL BODY 12 on cart• Make sure screw drops into rear cart brackets• Push GRILL BODY 12 to  back of cart• Install 2 screws in FRONT BRACKETS (Removed from Step 12 and Step 13)• Tighten 4 screws on cart brackets (2 screws left over will be used in future steps)

Step 15

• Remove 4 screws from GREASE CUP BRACKETS 22• Install GREASE CUP BRACKETS 22 to the bottom of the GRILL BODY  12 using 4 screws

Step 16

• Remove 2 screws• Attach GREASE CHANNEL 26• Tighten 2 screws

Step 17

• Loosen 2 screws• Attach LEFT SIDE CONTROL PANEL 21 to LEFT SIDE TABLE 19 over keyholes• Tighten 2 screws• Remove 1 screw and washer

 

Step 18

• Attach LEFT SIDE TABLE 19 to GRILL BODY 12 using keyholes• Do not tighten screws at this time• Install and tighten screw (Removed from Step 13)

Step 19

• Install screw and washer (Removed from Step 17)• Make sure control panels are aligned• Tighten 5 screws from Step 18 and Step 19

Step 20

• Remove 1 screw• Loosen 2 screws• Attach RIGHT SIDE CONTROL PANEL 20 to PELLET HOPPER 18 over keyholes• Tighten 2 screws

Step 21

• Attach PELLET HOPPER 18 to GRILL BODY  12• Tighten 4 screws (Find M6x35 screws bag with owners manual)

Step 22

• Install 2 screws (1 screw removed in Step 12 and 1 screw removed in Step 20)

Step 23

• Install PELLET HOPPER LID HANDLE 17 (screws, washers and bezels are pre-installed in handle)

Step 24

• Install TEMPERATURE GAUGE 14 and BEZEL 15 using washer and wing nut

Step 25

• Install HOOD HANDLE 13 (Wing nuts, bezels and washers are pre-installed on handle)

Step 26

• Remove 4 screws and washers• Loosen 1 screw

Step 27

• Install AUGER HOUSING 32 using keyhole in firebox and slots in pellet hopper bracket• Tighten 5 screws and washers in firebox

Step 28

• Remove 2 screws• Attach CORD WRAP 28 using 2 screws

Step 29a

• Connect wiring for Controller and Pellet Sensor• These wires can only be connected one way• Make sure the connectors are lined up properly before tightening

Step 29b

• Once connected, twist to tighten

Step 29c

• Secure wiring with cord clip.

Step 30

• Attach CONTROL KNOB  16 to controller

Step 31

• Attach HEAT BAFFLE 29

Step 32

• Install LEFT HEAT PLATE 30 on welded bracketsNote: The 2 longer feet go on the left side of the firebox

Step 33

• Install RIGHT HEAT PLATE 31 on welded bracketsNote: The angled lip should face left

Step 34

• Install COOKING GRATES  27 and WARMING RACK 24

Step 35

• Install ASH CATCHER 25 and GREASE CUP  23

Step 36

• Store GRIDDLE 36 on ACCESSORY HOOKS 33

Step 37

• Store CERAMIC INSERT 34 and CHARCOAL INSERT 35 on ACCESSORY HOOKS 33

Model SMK0036AS / SMK0036AS0 Assembled

OM0036AS/ASO1019

©2019 The Boltz Group LLCCarrollton, Texas 75006 U.S.A.

Assembly Instructions for ModelsSMK0036AS / SMK0036ASO

Cuisinart Woodcreek 4-in-1 Pellet Grill [SMK0036AS, SMK0036ASO] Instruction Manual – Cuisinart Woodcreek 4-in-1 Pellet Grill [SMK0036AS, SMK0036ASO] Instruction Manual –