Cypress Hills Marana Wide Console Table Instruction Manual

Cypress Hills Marana Wide Console Table

IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference.

SAFETY INFORMATION

Identify all the parts and hardware. Do not discard of the packaging until you have checked that you have all of the parts and hardware required.Hardware package may have spare parts.

WARNING: This item contains small parts which can be swallowed by children and pets. Keep children and pets away during assembly. To avoid danger of suffocation, always keep plastic bags away from children and pets.We recommend that you assemble this unit on a carpeted floor to avoid scratches. If using power tools, set the tool to low torque to avoid damage.

May require 2 people for ease of assembly

CARE and MAINTENANCE

Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions. As humidity changes, the components of wooden objects are continually pushing and pulling against each other. This pressure often results in parts of furniture no longer fitting together closely or becoming distorted or breaking from their own internal stresses.

The response to relative humidity changes begins with determining the annual average RH for your particular space. Then try to keep the RH in the space where your furniture is as close to that average as possible, generally within about 10% up or down. De humidify in the summer and humidify in the winter.

Be aware that raising the temperature lowers the humidity and vice versa. Thus, modern heating systems, which can drive down interior RH in the winter, almost invariably cause problems for furniture. To counteract their effect, you can either modify the RH by keeping furniture containing spaces cooler in the winter or most importantly, have a good working humidifier for your home. A humidistat automatically works to balance the humidity in your home so it is constant. Dry indoor air can suck enough moisture from its surroundings to do permanent damage to wood, causing it to crack or split.

Remember, that not all woods are created equal. Two factors that help determine how rapidly a wood will lose moisture are pore size and surface hardness. A piece made from a dense and hard wood will dry less rapidly than pieces made from softer woods.

Furniture that is sealed and lacquered will lose moisture more slowly than an unfinished piece while pieces with veneer finishes are not only stronger, but lose moisture more slowly than other finishes.

To help protect your wood furniture, take these steps:

  • Use a humidifier, preferably one with an automatic control system that can sense the humidity level and adjust itself accordingly. Don’t over-humidify; that can damage wood by causing it to expand and contract.
  • Keep furniture out of direct sunlight, which can cause it to dry out, crack and warp.
  • If you can avoid it, don’t put furniture near heating vents. If you must, keep the piece 3 to 4 inches away from the wall, giving the heat and air space to circulate.
  • Dust with soft dry cloth.
  • Do not use liquid or aerosol products.
  • To avoid marking, do not place rubber on surface (foot pads, etc.)
  • For soil build-up, wipe with damp cloth & dry.
  • Do not use abrasive cleaners.

PRE-ASSEMBLY INFORMATION

PART DESCRIPTION

TOP QTY 1

LEG QTY 4

HARDWARE DESCRIPTION

ALLEN KEY BOLT: M6 X 50mm – QTY 8LOCK WASHER: Ø10 / Ø6 X 1.5mm – QTY 8WASHER: Ø16 / Ø6 X1mm – QTY 8QTY 8 SETS

ALLEN KEYQTY 1

HANDLEM4X 30mmQTY 3 SETS

Required –Flathead screwdriverPhillips screwdriverNot Included

NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-800-667-8992.

COMPONENTS-KEY DIAGRAM

ASSEMBLY

STEP-1

  1. Remove the drawers from Top A by pressing the locks on the glides.
  2. Attach Handles to part .
  3. Use Phillips screwdriver to tighten screws. Do not over-tighten.

STEP-2

  1. Attach Legs to the Top .
  2. Use 8 Allen Key Bolts, Lock Washers and Washers to fix part and .
  3. Use Allen Key to tighten Bolts. Do not over-tighten.

STEP-3

  1. Insert assembled drawer into glides on assembled table.Note: Levelers on bottom of legs can be adjusted if floor is uneven.

 

FOR REPLACEMENT PARTS OR OTHER INQUIRIES PLEASE CONTACT US AT:1-800-667-8992

PLEASE ENSURE TO HAVE THE COLLECTION NAME AND DESCRIPTION FROM THE PACKAGING OR INSTRUCTION BOOKLET

[xyz-ips snippet=”download-snippet”]


Posted

in

by