D-Link DWL-8720AP Unified AC Dual-Band PoE Outdoor Access Point Installation Guide

Quick Installation Guide802.11ac Unified Wireless Outdoor PoE Access PointDWL-8720AP

Introduction

This Quick Installation Guide gives instructions for setting up the D-Link DWL-8720AP Access Point. The model you have purchased may appear slightly different from those shown in the illustrations. For more detailed information about the access  point, configuring the device, and technical specifications, please visit the website http://www.dlink.com/

Package Contents

Open the shipping carton of the Acces Point and carefully unpack its contents. Please consult the packing list located to make sure all items are present and undamaged.

• DWL-8720AP
• External Omni-directional antennas
• Wall/pole mounting kit
• Console cable
• Grounding wire

If any of the above items are damaged or missing, please contact your local reseller for replacement.

Hardware Overview

LED Indicators

Connecting to Power

GroundingUse the grounding wire for grounding the DWL-8720AP.

Powering the Access Point

You can use PoE (802.3af) to power the DWL-8720AP:

1. You can directly connect the LAN port on the DWL-8720AP to any available PoE-capable port of an 802.3af-compliant PoE switch (not included in the Package Contents), as illustrated below.
2. Alternatively, you may power the DWL-8720AP by connecting a PoE injector’s PoE-OUT (not included in the Package  Contents) to the LAN port on the DWL-8720AP. Then connect the PoE injector’s LAN-IN port to an available Ethernet port on your switch or router and plug in the injector’s power cord into a power outlet as shown below.
3. The green PWR indicator at the bottom panel will illustrate the device is powered properly.

Configuring the Access Point

The DWL-8720AP can be powered using one of the following methods:Connecting to a PC

1. Use the console cable to connect DWL-8720AP to a PC.
2. Ensure the computer is configured with a static IP address in the 10.90.90.0/24 subnet. Launch a web browser, type the default IP address of the access point (http://10.90.90.91), then press Enter.
3. After the logon pop-up screen appears, type “admin/admin” for the username and password fields. Click Logon.

Connecting to Switch or Router

1. Connect the access point and the computer to the same switch or router.
2. If the access point did not acquire an IP address from a DHCP server on the network, enter the default IP address of the access point 10.90.90.91 in the address field of your browser. If the access is automatically assigned an IP address by a  DHCP server on your network, enter the IP address assigned to the access point into the web browser.
3. After the logon pop-up screen appears, type “admin/admin” for the username and password fields. Click Logon.

Connecting to Wireless Controller

1. Connect the access point to a Wireless Controller. Connect your computer to the same network as that of the Wireless  Controller.
2. Log in to the Wireless Controller’s web administration page. For information about configuring the device please refer to the Wireless Controller user manual.

Access Point Installation

Mounting the AP to a Wall

1. Remove the nut and washer from the bolts and place the bolts in the holes.
2. Use the mounting base plate to mark the location on the surface where you want to mount the DWL-8720AP. Next, drill the holes on all 4 markings.

Mounting the AP to a Pole

1. Use the brackets included into the mounting kit to fasten the mounting plate to the pole.
2. Use the screws to fasten DWL-8720AP to the mounting plate.

Antennas Installation

Сonnect the antennas to the corresponding connectors on the AP. The DWL-8720AP is now ready to be connected to the network.

Additional Information

For more detailed information on how to set up and configure the access point, please visit the website http://www.dlink.com/

References

• 
  Consumer | D-Link
• 
  D-Link Главная
• 
  D-Link Главная
• 
  dlink.com/warranty
• 
  D-Link Support