Dawson MICRO ELECTRIC ROPE HOIST Instructions
Congratulations for your excellent choice on our new electric tool which is compliance with the best and reliable standards,ensuring you efficiency and safety for a long period of time
GENERAL SAFETY RULES
WARNING! Before using this electric tool. Carefully read the general safety rules listed below.
- Your sockets must comply with safety rules. In case your sockets are not suitable, it should be checked by a skilled electrician.
- Your sockets plug must absolutely be grounded and your electric system must be supplied with a magneto cut out safety.
- When the machine is running unattended, be careful that children cannot reach it.
- Do not pull the electric cable to disconnect the plug.
- The machine shall be protected from frost and low temperatures.
- In case the machine cannot hoist a load,do not keep pressing the hoisting Push button, this means that the load exceeds the machine maximum capacity.
- The machine shall not be disassembled when running or connected to power.
- Do not stand under hoisted weights.
- Before starting the work, make sure that the steel cable is correctly winded around the reel and the pitch is equal to the cable diameter.
- Observe the maximum load indicated on the hoist.not that no the hook!
- Leave at least three tums of cable around the reel,so that the cable connection is not under stress.
- To avoid any danger, do not wind more than 15 m of cable around the reel
- In case the steel cable is worn,it must be replaced only with a cable of same features manufactured by us. If can be found at all authorized service shops.
- In case the hoist stops during the lowering of a load,it is normal that the load goes down a few centimeters more because of inertia.
- Attention! The hoist electric motor isn’t equip with any overload cut-out(to avoid an unexpected and unwanted restart)therefore,if you are unable to hoist a load do not insist and let the motor cool down.
Specifications
| Specification | Method of use | Rated volt (v) | Input power (W) | Ratelifting Weight(KG) | Lifting speed (m/min) | Lifting height (m) | Quan tity (PCS) | Size (cm) | GW./NW. (KG) |
| PA200 | Single-hook | 110/220 | 510 | 100 | 10 | 12 | 1 | 38*15*24 | 10/9.5 |
| Double-hook | 200 | 5 | 6 | ||||||
| PA300 | Single-hook | 110/220 | 650 | 150 | 10 | 12 | 1 | 38*15*24 | 11/10 |
| Double-hook | 300 | 5 | 6 | ||||||
| PA400 | Single-hook | 110/220 | 850 | 200 | 10 | 12 | 1 | 44*15*25 | 15/14 |
| Double-hook | 400 | 5 | 6 | ||||||
| PA500 | Single-hook | 110/220 | 1050 | 250 | 10 | 12 | 1 | 44*15*25 | 15.5/14.5 |
| Double-hook | 500 | 5 | 6 | ||||||
| PA600 | Single-hook | 110/220 | 1200 | 300 | 10 | 12 | 1 | 44*15*25 | 16/15 |
| Double-hook | 600 | 5 | 6 | ||||||
| P800 | Single-hook | 110/220 | 1450 | 400 | 10 | 12 | 1 | 44*15*25 | 17/16 |
| Double-hook | 800 | 5 | 6 | ||||||
| PA1000 | Single-hook | 110/220 | 1600 | 500 | 10 | 12 | 1 | 53*24*35 | 28/27 |
| Double-hook | 1000 | 5 | 6 | ||||||
| PA1200 | Single-hook | 110/220 | 1800 | 600 | 10 | 12 | 1 | 53*24*35 | 30/29 |
| Double-hook | 1200 | 5 | 6 |
MAINTENACE
Periodically check that the steel cable is in good conditions.
- Check that the screws securing the brackets and reduction gear are welltightened.
- Check the conditions and tightening of the nuts securing the steel cable clamp.
- Regularly check whether the motor stop switch and button switch are in good working condition.
[xyz-ips snippet=”download-snippet”]