TACTILE BASS SHAKERModel: BST-2 User Manual
Thank you for purchasing the BST-2 Bass Shaker. The human ear has the ability to hear a wide range of sounds, however, some sound is simply too low to hear and must be felt through the body. Feeling this extremely low-frequency sound adds a new dimension to your listening, gaming, and movie experiences. With a BST-2 Bass Shaker, you’ll feel the thundering weight of a dinosaur’s foot slamming against the ground as it approaches. Your favorite action movies will come to life as you feel the cannon blasts and explosions impacting your body! Into gaming? The BST2 is the perfect addition to your gaming chair or couch! Feel the power and impact of a football tackle putting you on the field and in the game! Read the following instructions, paying close attention to wiring diagrams and cautions.
CONNECTING A SINGLE BASS SHAKER
The impedance of the BST-2 Bass Shaker is 4 ohms. When used in a single unit configuration it must be hooked up to an amplifier that is either stereo or bridged mono, the same way you would connect a subwoofer. Please consult the amplifier manual for details regarding the impedance rating of your amplifier.
CONNECTING MULTIPLE BASS SHAKERS
Two or Four Bass Shakers can be used in situations where more bass energy is desired or in larger applications. Connecting two in Series configuration will raise the impedance to 8 ohms, connecting two in Parallel will lower the impedance to 2 ohms, and wiring four Bass Shakers in Series-Parallel will keep the overall impedance to 4 ohms. Again, always consult your amplifier’s owner’s manual to verify it has the power capability that achieves the wattage and various impedances.
WARNING: Do NOT exceed 35 watts RMS per Bass Shaker multiplied by the number of Shakers (example: 35 x 4 = 140 Watts RMS)
INSTALLATION NOTES
Mounting Locations
HOME - Mounting the Bass Shaker to chairs or couches that are not fixed to the floor will provide the greatest effects. The energy of the Bass Shaker will impact the user’s body rather than travel through the furniture and disperse the energy into the floor. Isolating the furniture from the floor is highly recommended by using pads or rubber feet. Find a solid mounting area for your Bass Shaker(s) underneath and/or on the rear of the furniture’s construction. Use four wood screws or bolts to mount the Bass Shaker to the structure. Should no solid mount exist it is recommended that one be constructed using hardwood or plywood. Try to avoid fabric or padding coming into contact with the Bass Shaker. It is important the Bass Shaker comes in full contact with a solid flat surface. Recommended wire gauge is 14-16 Gauge Speaker Wire.
AUTO - Mounting the Bass Shaker under the seats is highly recommended rather than on the seat itself. Move (or remove) your seat forward as far as possible, and identify the spot under the seat that vibrates the most by knocking on the flooring using a rubber mallet or soft hammer. Again, ensuring the Bass Shaker comes into full contact with the floor surface is critical to the performance of the Bass Shaker. Wiring in advance of the installation is recommended. Ensure your wire is without kinks or bends and that no bare wire is touching metal. Use four steel screws or stingers to mount the Bass Shaker to the floor of your vehicle. Recommended wire gauge is 14-16 Gauge Speaker Wire.
WARNING: Always check under carpeted locations and recheck the mounting area so as to not cut or drill into any existing electrical wiring, airbag sensors, hydraulics, brakes, gas, or fuel lines.
ADDITIONAL NOTES AND SUGGESTIONS:
- An 80 Hz low pass crossover is suggested to reduce the possibility of unwanted high-frequency output.
- Recommended Amplifiers: Dayton Audio SA 70 for 1 to 2 BST-2 bass shakers, Dayton Audio APA150 for 4 BTS-2 bass shakers (wired in series-parallel for a 4-ohm load), and a Dayton Audio BSA-200 for 6 BST-2 bass shakers (wired in series-parallel for a 6-ohm load).
SPECIFICATIONS:
Housing: High-Grade AluminumImpedance: 4 ohmsPower Handling: 35 Watts RMSWeight: 2.6 lbs
5-Year Limited WarrantySee daytonaudio.com for details
daytonaudio.comtel + 937.743.8248[email protected]
705 Pleasant Valley Dr.Springboro, OH 45066USA
Dayton Audio®Last Revised: 11/5/2020
References
[xyz-ips snippet=”download-snippet”]