DELL U4320Q UltraSharp 43 inch 4K USB-C Monitor
Disassembly Procedures
S1Remove 4pcs carton locks, then use a proper tool to open the carton, then uplift and remove the top paper box carefully.
S2Remove the top cushion foam with all accessories including QSG, Delta-e paper, user’s manual, DP cable, HDMI cable, Type-C cable, USB cable, power cable and other packing materials.(Note: It depends on whether users returning the accessories)
S3Take out the base and stand from bottom cushionfoam, then take out the packed monitor from thebottom cushion foam
S4Take out the monitor from EPE-bag and put the LCDmonitor on a protective cushion.
S5Use a Philips-head screwdriver to remove 4pcs screws for unlocking mechanisms.(No.1~4 screw size=M6x12; Torque=9±0.5kgfxcm)
S6Wedge your fingers between the rear cover and the middle bezel on the corners of the top side of the monitor to release the rear cover, then use one hand to press the middle bezel, the other hand to pull up carefully the rear cover in order of arrow preference for unlocking mechanisms of rear cover.
S7Lift the rear cover up carefully. Disconnect the USB LVDS cable and function key cable from the connectors of the interface board, and then remove the rear cover.
S8Use a Philips-head screwdriver to remove 1pcs screw for unlocking the USB board unit, then release the USB board unit and put it aside.(No.1 screw size=M3x6, Torque=4±0.5kgfxcm)
S9Use a Philips-head screwdriver to remove 8pcs screws for unlocking the speakers with middle bezel. Release the speakers’ cables from the hooks of the middle bezel, and then disconnect the speaker cable away from the connector of the circuit board.(No.1~8 screw size=M3x8, Torque=5±0.5kgfxcm)
S10Use a Philips-head screwdriver to remove 2pcs screws for unlocking the heat sink. se a Philips head screwdriver to remove 26pcs screws for unlocking the middle bezel, then remove the bezel.(No.1~28 Screw size= M3x0.5×4, Torque=5±0.5kgfxcm)
S11Put the rear cover with function key board into a Jib. Tear off the Mylar tape on the function key board, then use a Philips-head screwdriver to tighten 3pcs screws for locking the function key board with the front bezel.(No.1~3 Screw size= M2x2.4, Torque=0.8±0.2kgfxcm)
S12Tear off acetate tape, then disconnect the panel lamp cables from the connectors of the circuit board.
S13Use a Philips-head screwdriver to remove 4pcs screws for locking the bracket chassis module with the panel(No.1~4 Screw size= M6x12, Torque=9±0.5kgfxcm)
S14Lift up the bracket chassis, and disconnect the LVDS cable from the connector of the T-CON board of panel module, then put the bracket chassis on a protective cushion
S15Use a Philips-head screwdriver to remove 2pcs screws for unlocking the small bracket with T-Con board, then remove the small bracket.(No.1~2 Screw size= M3x0.5×4, Torque=3~5kgfxcm)
S16Remove 2pcs shading tape on the left and right side of the panel corner, then remove 32pcs acetate tapes on the specific positions of the back of panel.
S17Turn over the bracket chassis module. Remove the Mylar from the hooks of the bracket, and then use a Philips-head screwdriver to remove screws for unlocking AC power outlet. two (No.1~2 screw size=M3x10, Torque=6±0.5kgfxcm)
S18Use a Philips-head screwdriver to remove screws for unlocking power board and interface board. 9pcs(No.1 screw size=M4x8, Torque=6±0.5kgfxcm; No.2~6 screw size=M3x7.5, Torque=6±0.5kgfxcm)
S19Remove the circuit boards from the bracket chassis module carefully, and then disconnect all of the cables.
S20Remove electrolyte capacitors (red mark) from printed circuit boards.
Product material information
The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC.
Capacitors / condensers (containing PCB/PCT) | No used |
Mercury containing components | No used |
Batteries | No used |
Printed circuit boards (with a surface greater than 10 square cm) | Product has printed circuit boards (with a surface greater than 10 square cm) |
Component contain toner, ink and liquids | No used |
Plastic containing BFR | No used |
Component and waste contain asbestos | No used |
CRT | No used |
Component contain CFC, HCFC, HFC and HC | No used |
Gas discharge lamps | No used |
LCD display > 100 cm2 | Product has an LCD greater than 100 cm2 |
External electric cable | Product has external cables |
Component contain refractory ceramic fibers | No used |
Component contain radio-active substances | No used |
Electrolyte capacitors (height > 25mm, diameter > 25mm) | Product has electrolyte capacitors (height > 25mm, diameter > 25mm) |
Tools Required
List the type and size of the tools that would typically can be used to disassemble theproduct to a point where components and materials requiring selective treatmentcan be removed.
Tool Description
- Screwdriver (Phillip head) #1
- Screwdriver (Phillip head) #2
- Penknife
- Soldering iron and absorber
[xyz-ips snippet=”download-snippet”]