dji OE100 OM5 Smartphone-Gimbal User Guide

dji OE100 OM5 Smartphone-Gimbal User Guide

Safety at a Glance

Please read this entire document and visit http://www.dji.com/om-5 to view the user manual, other documents, and the tutorial videos with the most current instructions and warnings. Failure to read and follow instructions and warnings may result in personal injury, damage to your DJI OSMO^TM product, or other objects in the vicinity. This document and all other collateral documents are subject to change at the sole discretion of DJI OSMO.

By using this product, you hereby signify that you have read and agreed to abide by the terms and conditions of this document. You agree that you are solely responsible for your own conduct while using this product and for any consequences thereof. This product is not intended for use by children without direct adult supervision

Warning

1. DO NOT allow the product to come into contact with any kind of DO NOT leave the product out in the rain or near a source of moisture. DO NOT drop the product into water. If the inside of the battery comes into contact with water, chemical decomposition may occur, potentially resulting in the battery catching on fire, and may even lead to an explosion.
2. Put out any product fire using water, sand, fire blanket, or a dry powder fire extinguisher.
3. The product should be used in temperatures from 0º to 40º C (32° to 104° F). Use of the product in environments above 40º C (104° F) can lead to a fire or Use of the product below 0º C (32° F) can lead to permanent damage.
4. Never disassemble or pierce the product in any way or the battery may leak, catch fire, or explode.
5. DO NOT drop or strike the DO NOT place heavy objects on the product.
6. DO NOT heat the DO NOT put the product in a microwave oven or in a pressurized container.
7. DO NOT leave the product near heat sources such as a furnace or DO NOT leave the product inside of a vehicle on hot days. The ideal storage temperature is 22º C to 28º C (72° to 82° F).
8. DO NOT store the product fully discharged for an extended Otherwise, it will over discharge, which will lead to permanent damage.
9. DO NOT extend the extension rod during charging

Caution

1. Intricate components inside DJI^TM OM 5 may be damaged upon impact and cause the gimbal to be damaged.
2. Make sure there is nothing obstructing the gimbal when DJI OM 5 is powered on
3. DJI OM 5 is not water DO NOT use any liquid cleansers. Only use a soft dry cloth to clean DJI OM 5.
4. Keep DJI OM 5 away from sand and dust to safeguard the sensors in the motors.
5. DJI OM 5 consists of magnets. Keep it away from magcards, IC cards, pacemakers, hard disks, RAM chips, and other devices to avoid interference.
6. Make sure to align the marks on DJI OM 5 and the Magnetic Phone Clamp when attaching. Otherwise, the phone may fall off. The Magnetic Phone Clamp attach to DJI OM 5 via magnets. DO NOT move it too fast or make any sudden movements .
7. When the phone is attached to DJI OM 5, the compass feature of the phone may experience interference. In such cases, calibrate the compass according to the prompts in the phone
8. If a mobile phone has near-field communication and wireless charging features, these features may be affected by the phone clamp when it is These features will no longer be affected once the phone clamp is removed.

Specifications

Compliance Information

FCC Compliance NoticeSupplier’s Declaration of ConformityProduct name: DJI OM 5Model Number: OE100Responsible Party: DJI Technology, Inc.Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502Website: www.dji.com

We, DJI Technology, Inc., being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving

• • Reorient or relocate the receiving
  • Increase the separation between the equipment and receiver
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter

ISED Compliance Notice

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.

EU Compliance Statement: SZ DJI OSMO TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU.

A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

GB Compliance Statement: SZ DJI OSMO TECHNOLOGY CO., LTD. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.

A copy of the GB Declaration of Conformity is available online at www.dji.com/euro-compliance

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

This content is subject to change. Download the latest version from https://www.dji.com/om-5 OSMO is a trademark of DJI OSMO.Copyright © 2021 DJI OSMO All Rights Reserved.