dji OM 4 SE Create Magnetic Movement User Guide
Safety at a Glance
Please read this entire document and visit https://www.dji.com/om-4-se to view the user manual, other documents, and the tutorial videos with the most current instructions and warnings. Failure to read and follow instructions and warnings may result in personal injury, damage to your DJI OSMOTM product, or other objects in the vicinity. This document and all other collateral documents are subject to change at the sole discretion o DJI OSMO.By using this product, you hereby signify that you have read and agreed to abide by the terms and conditions of this document. You agree that you are solely responsible for your own conduct while using this product and for any consequences thereof. This product is not intended for use by children without direct adult supervision
Safety Guidelines
WARNING:
- DO NOT allow the product to come into contact with any kind of liquid. DO NOT leave the product out in the rain or near a source of moisture. DO NOT drop the product into water. If the inside of the battery comes into contact with water, chemical decomposition may occur, potentially resulting in the battery catching on fire, and may even lead to an explosion.
- Put out any product fire using water, sand, fire blanket, or a dry powder fire extinguisher.
- The product should be used in temperatures from 0º to 40º C (32° to 104° F). Use of the product in environments above 40º C (104° F) can lead to a fire or explosion. Use of the product below 0º C (32° F) can lead to permanent damage.
- Never disassemble or pierce the product in any way or the battery may leak, catch fire, or explode.
- DO NOT drop or strike the product. DO NOT place heavy objects on the product.
- DO NOT heat the product. DO NOT put the product in a microwave oven or in a pressurized container.
- DO NOT leave the product near heat sources such as a furnace or heater. DO NOT leave the product inside of a vehicle on hot days. The ideal storage temperature is 22º C to 28º C (72° to 82° F).
- DO NOT store the product fully discharged for an extended period. Otherwise, it will over discharge, which will lead to permanent damage.
caution
- Intricate components inside DJITM OM 4 SE may be damaged upon impact and cause the gimbal to damaged.
- Make sure there is nothing obstructing the gimbal when DJI OM 4 SE is powered on.
- DJI OM 4 SE is not water resistant. DO NOT use any liquid cleansers. Only use a soft dry cloth to clean DJI OM 4 SE.
- Keep DJI OM 4 SE away from sand and dust to safeguard the sensors in the motors.
- DJI OM 4 SE consists of magnets. Keep it away from magcards, IC cards, pacemakers, hard disks, RAM chips, and other devices to avoid interference.
- Make sure to align the marks on DJI OM 4 SE and the Magnetic Phone Clamp. Otherwise, the phone may fall off. The Magnetic Phone Clamp attach to DJI OM 4 SE via magnets. DO NOT move it too fast or make any sudden movements.
- When the phone is attached to DJI OM 4 SE, the compass feature of the phone may experience interference. In such cases, calibrate the compass according to the prompts in the phone.
- If a mobile phone has near-field communication and wireless charging features, these features may be affected by the phone clamp when they are attached. These features will no longer be affected once the phone clamp is removed.
Specifications
| Name | DJI OM 4 SE |
| Model | OK10 |
| Dimensions | Unfolded: 276×120×104 mmFolded: 163×100×47 mm |
| Weight | 390 g (gimbal)34 g (magnetic phone clamp) |
| Consumption | 1.2 W (steady and balanced status) |
| Mechanical Range | Pan: –161.2° to 172°Roll: -136.7° to 198°Tilt: -106.5° to 235.5° |
| Max Controllable Speed | 120°/s |
| Compatible Phones | Weight: 230±60 g Diagonal: ≤ 196 mm or ≤ 7.72 inchThickness: 6.9 – 10 mmWidth: 67 – 84 mm |
| Mode | Bluetooth Low Energy 5.0 |
| Transmitter Power (EIRP) | ≤4 dBm |
| Operation Frequency | 2.400-2.4835 GHz |
| Battery Type | 18650 Li-ion |
| Capacity | 2450 mAh |
| Energy | 17.64 WH |
| Voltage | 7.2 V |
| Charging Temperature | 5° to 40° C (41° to 104° F) |
| Operating Temperature | Operating Temperature |
| Charging Time | 2.5 hours (tested in an environmental temperature of 25° C (77° F) when using a 10 W charger) |
| Operating Time | 15 hours (under ideal conditions with the gimbal fully balanced) |
Compliance Information
FCC Compliance Notice
Supplier’s Declaration of ConformityProduct name: DJI OM 4Model Number: OK100Responsible Party: DJI Technology, Inc.Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502Website: www.dji.com
We, DJI Technology, Inc., being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and.
- This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure InformationThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter.
ISED Compliance NoticeThis device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Environmentally friendly disposalOld electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.
This content is subject to change.Download the latest version fromhttps://www.dji.com/om-4-seOSMO is a trademark of DJI OSMO.Copyright © 2021 DJI OSMO All Rights Reserved.
[xyz-ips snippet=”download-snippet”]