DRI-EAZ Stealth AV3000 Airmover Owner’s Manual

DRI-EAZ Stealth AV3000 Airmover

READ AND SAVE THESE INSTRUCTIONS

WARNING!

• To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
• Unit must be grounded. Do not use with an extension cord. Connect only to an outlet provided with a ground fault interrupting device.
• Never operate a unit with a damaged power cord, as this may lead to electrical or fire hazards. If power cord is damaged, it must be replaced by a cord of the same type and amperage rating.
• Do not touch grills when unit is operating.
• Keep motor dry. For indoor use only.
• Unplug when not in use or when moving unit.
• Do not allow children to play with or around the unit. Be sure the unit is inaccessible to children when not attended.
• Always operate the unit on a stable, level surface so it cannot fall and cause injury.
• Do not alter or modify the Stealth AV3000 in any way. Use only replacement parts authorized by Legend Brands, Inc. Modifications or use of unapproved parts could create a hazard and will void the product warranty. Contact an authorized DriEaz distributor for assistance.

WARNING! 

• a) Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
• b) Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.

BEFORE YOU BEGIN

Warranty registrationPlease visit warranty.drieaz.com to register your product. Registration allows Dri-Eaz to better assist with operation, maintenance, servicing of equipment, and to contact you in case there is important safety information concerning your Dri-Eaz product. If you determine service is required, have your equipment model, serial number and original proof of purchase available and call your distributor for assistance with obtaining a return material authorization (RMA).

Fig. A: Parts Identification

OPERATING INSTRUCTIONS

1. Unwrap the cord and plug the unit into a standard 115V GFCI-protected outlet. CAUTION: Be sure switch is in the off position before connecting unit to power outlet.
2. For ventilation, direct the Stealth outlet where desired. For drying, direct the outlet toward the surface to be dried. Secure the air mover orientation by tightening the knobs on either side of the unit.
3. When finished, unplug the unit and re-wrap the cord in the cord wrap.

Electrical safety devicesCircuit breaker: If the circuit breaker detects overload or short circuit conditions, the breaker will automatically shut off the electrical supply. If this should occur, check the power cable carefully for any damage and ensure it is plugged into a properly grounded outlet. Press the Circuit Breaker Reset Switch (Fig. A) to reestablish the electrical supply.

Fig. B: Disassembly for cleaning

Remove the four screws as shown and lift off the front assembly. Retain screws for reassembly. Do not overtighten screws.

Fig. C: Stacking for storage or transport

TRANSPORT AND STORAGE

Always use the handle to load or carry the unit.For cord storage, wrap cord around housing in groove. Pull cord snug and secure with plug clip (Fig. A).Units may be stacked up to five high for transport and storage (Fig. C). To stack, tip first unit back onto its outlet side and nest additional units on top (Fig. A).When transporting, secure the unit(s) carefully to prevent sliding and damage to the unit and/or injury to vehicle occupants.Keep unit dry. Do not expose the unit to rain or snow.

MAINTENANCE

WARNING: Unplug unit before performing any maintenance.

Before each useInspect the power cord. If cord is damaged, do not use. Always grasp the plug (not the cord) to unplug.

As neededClean housing and impeller. If dust accumulation is visible in the interior, remove the four screws from the outlet grill as shown (Fig. B). Clean impeller assembly and all surfaces with pressurized air and/or with a soft cloth. Do not apply liquids to the impeller assembly. The housing may be cleaned with a mild solution of detergent and warm water. Ensure housing is completely dry before reassembling.FOR SERVICE CALL YOUR LOCAL DISTRIBUTOR or the Dri-Eaz Service Department at 800-932-3030.

SPECIFICATIONS