DS18 HYDRO NXL-12SUB Marine and Motor sports 12″ Subwoofer Owner’s Manual

DS18 HYDRO NXL-12SUB Marine and Motor sports 12″ Subwoofer Owner’s Manual

FEATURES

• MARINE & MOTORSPORTS 12” SUBWOOFER
• IP65 Marine Grade Compliant 100% UV Stable
• Continuous Power Handling: 350W RMS
• Peak Music Power: 700W MAX
• Nominal Impedance: 4 Ohms
• Sensitivity: 91dB
• Frequency Response: 30Hz-500Hz

Components

Y35 Ferrite Main Magnet and Reverse N40H (Neodymium) Magnet Integrated LED-RGB Lighting

Materials

• Waterproof Injection PP Cone
• Soft Rubber Surround
• 316 Stainless Metal Mesh
• Injection ASA Grill with Gloss UV-Coating
• PC Injection Molded Composite Basket with Gloss UV-Coating

BT Control Module & App (LED-BTC) For Multi-Function for RGB LED Lighting (sold separately)

• Mounting Depth: 5.75″/146mm
• Cut-Out Diameter: 10.71″/272mm
• Overall Diameter: 12.81″/325.3mm
• Overall Height: 7.68″/195mm

PACKING INCLUDE

• 12” Marine & Motorsports Subwoofer
• 1 x 1.5M #16 Speaker Input Wired with Fast Terminal
• 1 x 1.5M #22 RGB LED Power Input Wired with Fast Terminal
• 6 x M5.2 Phillips Inner Hex Head 304 Stainless Steel (4mm Hex Tool)

WARNINGS

1. Be Sure to carefully read and understand the instructions before attempting to install these speakers.
2. For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
3. For easier assembly, we suggest you run all wires prior to mounting speaker in place
4. Use high quality connectors for a reliable installation and to minimize signal or power loss
5. Think before you drill. Be careful not to cut or drill gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle. If installing in a boat, take care not to cut or drill through the mail hull.
6. Never run wires underneath the vehicle. Running the wires inside the vehicle or hull area provides the best protection.
7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal – especially the firewall.

MOUNTING

1. Determine where the speakers will be mounted. Ensure an area large enough for the speaker to mount evenly. Be sure that the mounting location is deep enough for the speaker to fit; only mount to a flat surface. Use extra caution when mounting on panels with ureathane foam.
2. Refer to the specification chart to determine the proper diameter hole to cut for the speaker.
3. Mark the locations for the mounting screws. Drill the holes with a 0.75” bit.
4. Feed the speaker wires through the cutout and connect to the speaker terminals. Be sure to observe proper polarity when connecting the wires. The speaker’s positive terminal is indicated with a “+”.
5. Fit the speaker and mount into place using six (6) screws.
6. Tighten the screws until the speaker is in place.
7. LED CONNECTIONS – There are two options to choose from:If you have an LED Control Module (LED-BTC), connect as shown in the following diagram.The LED-BTC is an app based, BT Solution for RGB LED lighting control. The applications are truly limitless, lending to all types of environment, wether wet or dry. (SOLD SEPARATELY).Download the appWork with Android and Iphone 

To connect without LED Control Mocule (LED-BTC), connect as shown in the following diagram:

• Black wire ”BK” connected to battery Positive (+) 12V then choose one color:
• For Green color light: “G” Connected to Battery Negative (-)
• For Red color light: “R” Connected to Battery Negative (-)
• For Blue color light: “B” Connected to Battery Negative (-)
• For Purple color light: “R” and “B” Connected to Battery Negative (-)
• For Yellow color light: “R” and “G” Connected to Battery Negative (-)
• For Cyan color light: “B” and “G” Connected to Battery Negative (-)
• For White color light: “R”, “B” and “G” three wires Connected to Battery Negative (-)

Example of Green Light Connection: 

Specification

DIMENSION

WE LIKE IT LOUD