DURACELL 2 Amp Battery Charger / Maintainer (Model DRMC2A) User Manual

DURACELL 2 Amp Battery Charger + Maintainer (Model DRMC2A) User Manual

1. What’s Included

  1. Charger/Maintainer with LED indicators
  2. Quick-connect battery clamps
  3. Quick-connect ring terminal cable with replaceable fuse
  4. Four Phillips-head mounting screws (not shown)

WARNING: EXPLOSION HAZARD

A spark near the battery may cause an explosion. Follow instructions carefully to reduce the risk of spark near the battery. Do not face the battery when making the final connection.

WARNING: BATTERY DAMAGE

Do not use Li-Ion charging mode if you are connecting an SLA/AGM battery. Additionally, if you are connecting a Lithium-Ion battery, please ensure that Li-Ion mode is selected. Using the wrong charge mode may damage your battery.

CAUTION: EQUIPMENT DAMAGE

To avoid damaging your charging and battery charger cables, grasp each quick-connect terminal directly. Do not pull directly on either cord. Do not start the vehicle’s engine while the charger is still connected to the battery. This will damage the charger and void the warranty

2. Important Safety Information

  • Warnings identify conditions that may result in personal injury or loss of life.
  • Cautions identify conditions or practices that may damage the unit or other equipment.

IMPORTANT

This guide contains important safety and operating instructions in how to use the battery charger to recharge 6V and12V vehicle batteries.

  1. Do not expose the battery charger to moisture, rain, or snow.
  2. Use of an adapter not recommended due to potential risk of fire, electric shock, and/or injury.
  3. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting the battery charger.
  4. Do not operate the battery charger with damaged cord or plug — have the cord or plug replaced.
  5. Do not operate the battery charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; contact the manufacturer for repair or replacement.
  6. Do not disassemble the battery charger. Incorrect reassembly may result in shock or fire hazard.
  7. To reduce risk of electric shock, unplug the battery charger from the electric outlet before attempting any maintenance or cleaning.WARNING: RISK OF EXPLOSIVE GASESWorking in the vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal battery operation. For this reason, it is of utmost importance that each time before using a battery charger, you read this guide and follow the instructions exactly. To reduce risk of battery explosion, follow these instructions and those published by battery manufacturer and manufacturer of any equipment you intend to use in the vicinity of the battery. Review cautionary marking on these products and on any engine.Personal Precautions
  8. Someone should be within range of your voice or close enough to come to your aid when you work near a lead-acid battery.
  9. Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
  10. Wear complete eye protection and clothing protection. Avoid touching eyes while working near battery.
  11. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with running cold water for at least 10 minutes and get medical attention immediately.
  12. NEVER smoke or allow a spark or flame in the vicinity of battery or engine.
  13. Be extra cautious to reduce risk of dropping a metal tool onto a battery. It might spark or short-circuit the battery or other electrical part that may cause an explosion.
  14. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery. A lead-acid battery can produce a short-circuit current high enough to weld a ring or the like to metal, causing a severe burn.
  15. Use the battery charger for charging a 6V or 12V LEAD-ACID or LITHIUM-ION battery only. It is not intended to supply power to a low voltage electrical system. Do not use the battery charger for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst and cause injury to persons and damage to property.
  16. NEVER charge a frozen battery

Charger Location

  1. Place the battery charger as far away from the battery as the output DC cable permits.
  2. Never place the battery charger directly above a battery being charged; gases from battery will corrode and damage the charger.
  3. Never allow battery acid to drip on the charger when reading specific gravity or filling battery.
  4. Do not operate the charger in an enclosed area. Do not restrict ventilation in any way.
  5. Do not set a battery on top of the charger.

Failure to follow these safety guidelines may cause personal injury and/or damage to the battery charger. It may also void your product warranty

3. FCC Statement

This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply within the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced technician for help.

Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user’s authority to operate this equipment.

4. Canada ICES-003 Statement

This Class B digital apparatus complies with Canadian ICES-003.

  1. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
  2. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
  3. “This device complies with Industry license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.”

Recommended minimum AWG size for extension cords for battery chargers

5. LED Indicators

6. Using Your Charger

  1. Be sure the area around the battery is well-ventilated while the battery is being charged.
  2. Clean battery terminals before connecting.
  3. Follow all battery manufacturer’s recommendations.

7. Troubleshooting

8. Specifications

9. Recycling Information

Battery-Biz is committed to environmental responsibility and recommends that electronic devices be disposed of properly. Please contact your local city offices for information on recycling and disposal programs for e-waste.

For instructions on how to recycle this product visit http://www.call2recycle.org.

10. Contacting Customer Support

If you experience any problems or have any questions regarding this product, free technical support is available. Prior to calling, please review the technical support tips below. Call from a phone where you have access to your mobile device.

Be prepared to provide the following information:

  • Name, address and telephone number
  • Name of the DURACELL® product
  • Make and model of your device
  • Symptoms of the problem(s ) and what led to them

Technical Support is available by telephone:U.S. and Canada 1-800-300-1857Outside of the US/Canada: 805-437-7765

Written inquires should be directed to: Battery-Biz Inc.;DURACELL® Product Inquiry1380 Flynn Road, Camarillo, CA 93012, USA

DURACELL 2 Amp Battery Charger / Maintainer (Model DRMC2A) User Manual – DURACELL 2 Amp Battery Charger / Maintainer (Model DRMC2A) User Manual –

[xyz-ips snippet=”download-snippet”]


Posted

in

by