User manual
In the box
| Vacuum cleaner | ChargerCharges your vacuum with or without a dock. | Wall dockYour Dyson vacuum drops into the wall-mounted charging dock, readyfor your next clean. |
Some tools may not be included.
This tool has a combination of the brush head and crevice tool together in one unit. The brushthe head slides down the crevice tool when needed. |
A small cleaner head with a body housing themotor and an electrical connector to attach tothe wand or directly to the machine. |
This tool is angled and has a nozzle end. |
| Combi-crevice toolTwo tools in one – narrow nozzle and brush, for quick switching between cleaning and dusting tasks. | Mini motorized toolMotorized brush bar, concentrated in a smaller head to remove stubborn dirt from mattresses, upholstery, and stairs. | Worktop toolEngineered for cleaning kitchen worktops, tables, and hard surfaces. |
Getting started
Charging your machine
For the best experience, we recommend fully charging your machine, and any additional batteries, as soon as you open the box and after every clean.
The LED light on the end of the handle will flash when the power is running low and you need to put your battery on to charge.
Connect the charger directly to the charging point on the base of the handle of your machine. You can also connect to your dock as shown in the installation instructions supplied with your dock.
The LED light on the end of the handle will pulse with a blue LED light when charging, and the light will go out when fully charged.
It can take up to 3.5 hours to fully charge your battery. Your battery has been designed to be left on charge.
Your machine won’t operate or charge if the ambient temperature is below 5°C (41°F). This is designed to protect both the motor and battery.
You can help prolong the battery life by leaving your machine to cool down before recharging.
Emptying your bin
Empty your bin as soon as the dirt reaches the MAX mark.You may need to clean the filter more often if you use your machine with a full bin.The MAX mark on the bin of the machine, showing that the dirt should not be filled over the Max mark when the machine is at the angle of normal use.
Release the dirtHold your vacuum over a bin.
Illustration of the bin being emptied into a bag.
Push the red bin release button, taking care not to press the power button.The bottom of the bin will open and the shroud will slide down inside the bin,wiping away any dirt.
If the bin doesn’t open, check the bin release button is pushed down fully.
To remove the bin for emptying:
If the bin doesn’t empty fully, remove the bin and empty the dirt.
Press the red button located on the bin runner to release the bin and slideyour bin off the runner.
Minimize dust contact
The bin lid closes with an audible click and the bin is pushed upwards with another click once it is fully in place.
Cover your bin tightly in a dust-proof bag while you empty. Remove the bin carefully, seal the bag tightly and dispose of it.
Reassemble your machine
Two images of the bin with arrows showing the bin lid closing and a clicked symbol and the bin being pushed upwards with another click symbol.
If you have removed your bin, slide it back onto the runner. Make sure thatthe bin and lid are both securely in position.
Push the bin base upwards until the bin and lid both click into place.Reconnect the wand.
Cleaning your bin
|
|
| The bin being removed and the location of the bin release lever on the underside of the bin runner. | The bin is being pushed back into position on the bin runner. |
Don’t put any part of your machine in a dishwasher or use detergents, polishes, or air fresheners.
Clean your binIf it is necessary to clean your bin, empty it as shown in the ‘Emptying your bin’ section.
Press the red button located on the bin runner to release the bin and slide your bin off the runner.
Only clean your bin with a damp cloth.Make sure that the bin and seals are completely dry before replacing.
Replace your binInsert the spine onto the bin runner.
Close your bin by pushing the bin base upwards until the bin and bin base click into place.
Washing your filter
Wash your filter at least once a month to maintain the best performance.Make sure the filter is completely dry before refitting.
Twist off your filter
The filter is located at the rear of your machine.
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.
Turn your filter anti-clockwise and pull it away from your machine.
Before washing your filter, tap it gently over a bin to remove any loose dust and debris.
Wash your filter
Wash the outside of the filter, rubbing with your fingers to remove the dirt.Carefully rinse the inside filter, without allowing water to fill the filter.Repeat these steps until the water runs clear.
Shake and dry
Empty the filter and shake firmly to remove excess water.Keep shaking until there’s no water coming from the filter.
Place your filter end up, as shown.
Leave your filter to dry for at least 24 hours in a well-ventilated, warm place.
Don’t dry your filter in a tumble dryer, microwave or near a naked flame.
Important: your filter must be completely dry before you put it back into themachine. Your machine could be damaged if used with a damp filter.
Refit your filter
The filter is left to dry with the pleated filter end facing upwards.
To refit your filter, slide it onto the handle and turn it clockwise until it clicks into place.
Your filter may need more frequent washing if you vacuum fine dust, use Max mode frequently, or use with the bin full.
Cleaning your tools
Don’t put any part of your machine in a dishwasher or use detergents, polishes, or air fresheners.
Wipe with a damp, lint-free cloth, without touching the connector end.
Make sure your tools are completely dry before using.
Clearing blockages
If your machine detects a blockage, the motor will pulse six times. You won’t be able to use your machine until the blockage has been cleared.
If you try to use your machine when the motor is pulsing, it will automatically cut out.
Leave your machine to cool down before looking for blockages and, for your safety, take care not to touch the power button.
Looking after your machine
To always get the best performance from your machine, it’s important to clean it regularly and check for blockages.
report this adLook after your machineIf your machine is dusty, wipe with a damp lint-free cloth.Check for blockages in the cleaner head and tools of your machine.Wash your filter regularly and leave to dry completely.Don’t use detergents or polishes to clean your machine.Look after your batteryTo get the best performance and life from your battery, use Eco mode.Your machine won’t operate or charge if the ambient temperature is below 5°C (41°F). This is designed to protect both the motor and battery.Your serial numbersYou can register your machine using the serial number found on the bottom of your machine.You can find your serial numbers on your machine, battery, and charger.Use your serial number to register.
SV12 JN.00000 PN.000000-00-00 00.00.00 VERSION NO.01
[xyz-ips snippet=”download-snippet”]