E-flite Twin Otter 1.2m Instruction Manual

Table of Contents

Twin Otter 1.2m

SAFE® Select Technology, Optional Flight Envelope Protection

Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni

NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com or www.towerhobbies.com and click on the support or resources tab for this product.Meaning of Special Language: The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury. CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury. NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

14+ AGE RECOMMENDATION: Not for children under 14 years. This is not a toy.

WARNING AGAINST COUNTERFEIT PRODUCTS: If you ever need to replace your Spektrum receiver found in a Horizon Hobby product, always purchase from Horizon Hobby, LLC or a Horizon Hobby authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum technology.

Safety Precautions and Warnings

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of others.

· Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.

· Never operate your model with low transmitter batteries. · Always keep aircraft in sight and under control. · Always use fully charged batteries.

· Always operate your model in open spaces away from full-size vehicles, traffic and people.· Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.).· Always keep all chemicals, small parts and anything electrical out of the reach of children.· Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture causes damage to electronics.· Never place any portion of the model in your mouth as it could cause serious injury or even death.

· Always keep transmitter powered on while aircraft is powered. · Always remove batteries before disassembly. · Always keep moving parts clean. · Always keep parts dry. · Always let parts cool after use before touching. · Always remove batteries after use. · Always ensure failsafe is properly set before flying. · Never operate aircraft with damaged wiring. · Never touch moving parts.

Twin Otter 1.2m

Quick Start Information

Transmitter Setup

Set up your transmitter using the transmitter setup chart

Low Rate

Hi Rate

Ail

Dual Rates

Ele

Rud

8mm 8mm 10mm

12mm 12mm 20mm

Flaps

Half q=10mm

Full q=20mm

Center of Gravity (CG)

45mm (±5mm) from leading edge of wing at the fuselage

Flight Timer Setting

6 minutes, initially

Specifications

Box Contents

Motors: 22101350Kv (EFLM300514)

Installed Installed

ESCs: 20A Brushless ESC (EFLA300515)

Installed Installed

Servo: 9 gram servos (SPMSA330R)

Installed Installed

Receiver: SpektrumTM AR631 6-Channel Sport Receiver (SPMAR631)

Installed

Required to Complete

Recommended Battery: 11.1V 3S 2200 3200mAh Li-Po (SPMX22003S30, SPMX22003S50, SPMX22003S100)

Required to Complete

Recommended Battery Charger: Compatible LiPo Required to Required to

battery balancing charger

Complete Complete

Recommended Transmitter: Full-Range 6 channel 2.4GHz with Spektrum DSMX® technology with adjustable Dual Rates

Required to Complete

(48 in 1219mm)

36.75 in (933mm)

37~39.5 oz (1049~1118g)

Table of ContentsSAFE® Select Technology (BNF Basic) ………………………………………………….4 Preflight …………………………………………………………………………………………. 4 Model Assembly ………………………………………………………………………………4 Receiver Installation (PNP) …………………………………………………………………6 Transmitter Setup (BNF)…………………………………………………………………….6 Battery Installation and ESC Arming …………………………………………………….7 Center of Gravity ……………………………………………………………………………..7 Transmitter and Receiver Binding/ Switching ON and OFF SAFE Select (BNF) …………………………………………..8 SAFE® Select Switch Designation………………………………………………………..9 Control Surface Centering ………………………………………………………………….9 Control Surface Direction …………………………………………………………………10 Dual Rates and Control Throws …………………………………………………………10 AS3X Control Direction Test (BNF) …………………………………………………….11 In Flight Trimming (BNF)…………………………………………………………………..11 Flying Tips and Repairs ……………………………………………………………………12 SAFE Select Flying Tips……………………………………………………………………12 Post Flight …………………………………………………………………………………….13 Motor Service ……………………………………………………………………………….. 13 Float Assembly and Installation…………………………………………………………14 Flying Off Water ……………………………………………………………………………..14 Replacement Parts, Optional Parts, Recommended Receivers (PNP) ………..15 AMA National Model Aircraft Safety Code……………………………………………16 Troubleshooting Guide AS3X/Troubleshooting Guide ……………………………..17 Limited Warranty ……………………………………………………………………………18 Contact Information ………………………………………………………………………..18 FCC Information……………………………………………………………………………..19 IC Information ………………………………………………………………………………..19 Compliance Information for the European Union…………………………………..19

Channels Frequency Compatibility

RECEIVER BIND INFORMATION (BNF) 624052476 MHz DSM2 and DSMX

As of this printing, you may be required to register with the FAA if you own this product.For up-to-date information on how to register with the FAA, visit https://registermyuas.faa.gov/For additional assistance on regulations and guidance on UAS usage, visit https://knowbeforeyoufly.org/To receive product updates, special offers and more, register your product at https://www.horizonhobby.com/content/e-flite-rc3

SAFE® Select Technology (BNF Basic)The BNF Basic version of this airplane includes SAFE Select technology which can offer an extra level of protection in flight. Use the following instructions to make the SAFE Select system active and assign it to a switch. When enabled, SAFE Select prevents the airplane from banking or pitching past predetermined limits, and automatic self-leveling keeps the airplane flying in a straight and level attitude when the aileron, elevator and rudder sticks are at neutral.SAFE Select is enabled or disabled during the bind process. When the airplane is bound with SAFE Select enabled, a switch can be assigned to toggle between SAFE Select mode and AS3X mode. AS3X® technology remains active with no banking limits or self leveling any time SAFE Select is disabled or OFF.Preflight

SAFE Select can be configured three ways: · SAFE Select Off: Always in AS3X mode · SAFE Select On with no switch assigned: Always in SAFE Select mode · SAFE Select On with a switch assigned: Assigned switch toggles between SAFE Select mode and AS3X mode

1 Remove and inspect contents. 2 Read this instruction manual thoroughly. 3 Charge the flight battery. 4 Set up the transmitter using transmitter setup chart. 5 Fully assemble the airplane. 6 Install the flight battery in the aircraft (once it has been fully charged). 7 Check the Center of Gravity (CG). 8 Bind the aircraft to your transmitter.

9 Make sure linkages move freely. 10 Test the flap operation. 11 Perform the Control Direction Test with the transmitter. 12 Perform the AS3X Control Direction Test with the aircraft. 13 Adjust flight controls and transmitter. 14 Perform a radio system Range Test. 15 Find a safe open area to fly. 16 Plan flight for flying field conditions.

Model AssemblyLanding Gear Installation1. Remove the screw (2mm x 15mm) on the bottom of the fuselage and remove the landing gear cover.2. Install the six mounting screws (2mm x 10mm) and three landing gear mounting clamps as shown.3. Reinstall the landing gear cover and tighten the fuselage screw (2mm x 15mm).4. Install the nose wheel, aligning the flat area on the nose gear with the set screw in the nose gear bracket.TIP: The steering arm for the water rudder can be removed when flying with wheeled landing gear if desired.5. Tighten the set screw.TIP: Apply a drop of CA to the landing gear strut covers and nose gear set screw, if desired.

Horizontal Tail Installation1. Slide the horizontal stabilizer into place within the vertical fin, inserting it with the elevator control horn on the bottom of the stabilizer and the right side of the fuselage.2. Install two screws (2mm x 10mm) on each side of the horizontal tail, as shown. 3. Move the elevator up and down several times. If the elevator joiner binds againstthe fuselage, continue to flex it until the binding is eliminated to allow for proper movement. TIP: Check and tighten any screws securing the control horns as needed. Do not overtighten the screws as it could damage the control surface and/or control horn. 4. Snap the elevator clevis into place, then snap the rudder clevis into place, if needed. 5. Slide the horizontal stabilizing fins into place. TIP: You may apply a drop of CA to secure the horizontal stabilizing fins, if desired.4

4 25

1 5

Twin Otter 1.2m

Model Assembly ContinuedWing Installation1. Connect the ESC, ailerons, LED lights, and flaps to the receiver in the following locations: 1ESC 2Aileron 3Elevator 4Rudder 5LED Lights 6Flaps2. Install the wing, then secure it by tightening the thumb screw as shown. 3. Slide each wing strut into the fuselage slot. 4. Snap each wing strut into place at rear of motor nacelle.1

ENAR631 Port AssignmentsBND/PRG = BIND 1 = ESC 2 = Aileron 3 = Elevator 4 = Rudder 5 = LED Lights 6 = Flaps34

Propeller InstallationWARNING: Do not install the propeller until all system setups are complete. Failure to heed this warning could result in severe personal injury. 1. Determine which propeller matches each image and install as shown. 2. Install the left propeller (T7056C) on the left propeller adaptor. Install the right propeller (T7056CR) on the right propeller adaptor. Tighten each nut to secure each propeller in place. The nut securing the T7056CR propeller on the right wing is reverse threaded. 3. Install the spinners and secure them in place with a 2mm x 10mm machine screw.T7056CR

T7056C

ENReceiver Installation (PNP)The Spektrum AR631 receiver is recommended for this airplane. If you choose to install another receiver, ensure that it is at least a 5-channel full range (sport) receiver. Refer to your receiver manual for correct installation and operation instructions. Installation (AR631 shown) 1. Mount the receiver parallel to the length of the fuselage as shown. Usedouble-sided servo tape.CAUTION: Incorrect installation of the receiver could cause a crash.2. Attach the appropriate control surfaces to the their respective ports on the receiver using the chart in the illustration.

AR631 Port AssignmentsBND/PRG = BIND1 = ESC 2 = Aileron 3 = Elevator 4 = Rudder 5 = LED Lights 6 = Flaps

Transmitter Setup (BNF)IMPORTANT: After you set up your model, always rebind the transmitter and receiver to set the desired failsafe positions. If you are using a 6 channel transmitter, the FLAP Channel (CH 6) controls the flaps.Dual RatesAttempt your first flights in Low Rate. For landings, use high rate elevator. NOTICE: To ensure AS3X technology functions properly, do not lower rate values below 50%. If lower rates are desired, manually adjust the position of the pushrods on the servo arm. NOTICE: If oscillation occurs at high speed, refer to the Troubleshooting Guide for more information.ExpoAfter first flights, you may adjust expo in your transmitter.Some of the terminology and function locations used in the iX12 and iX20 programming may be slightly different than other Spektrum AirWareTM radios. The names given in parenthesis correspond to the iX programming terminology. Consult your transmitter manual for specific information about programming your transmitter. *Flap programming values may vary slightly. For your initial flights use the recommended flap travel settings provided in the Flaps section and adjust the flap travel to your preference on subsequent flights.

Computerized Transmitter Setup

Start all transmitter programming with a blank ACRO model (perform a model reset), then name the model.

Set Dual Rates to

HIGH 100% LOW 70%

Set Expo to

HIGH 20% LOW 15%

Set Servo Travel to

100%

Set Throttle Cut to

-130%

DXeDX6iDX7S DX8DX6e DX6 (Gen2) DX7 (Gen2) DX8e DX8 (Gen2) DX9 DX10t DX18 DX20 iX12 iX20 NX6 NX8 NX10

Refer to spektrumrc.com for the appropriate download setup.

1. Go to the SETUP LIST MENU

2. Set MODEL TYPE: ACRO

3. Go to ADJUST LIST MENU

4. Set TRAVEL: FLAPS £-100 100

5. Set FLAPS:

Norm -100 Flap LAND £100 Flap

Elev 0 Elev 35

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Set WING TYPE: 1 AIL 1 FLAP

4. Go to the FUNCTION LIST

5. Set FLAP SYSTEM: Choose Flap

NORM: -100% FLAP

MID: 0% FLAP

25% Elevator

LAND: 100% FLAP

35% Elevator

SPEED 2.0S: SWITCH = D

1. Go to the SYSTEM SETUP (Model Utilities)

2. Set MODEL TYPE: AIRPLANE

3. Set AIRCRAFT TYPE (Model Setup, Aircraft Type): WING: 1 AIL 1 FLAP4. Set CHANNEL ASSIGN (Model Setup, Channel Assign): (Default switch assignments with a new model setup)Flap (CH6): SWITCH D

5. Go to the FUNCTION LIST (Model Adjust)

6. Set FLAP SYSTEM: SELECT SWITCH D: POS 0: -100% FLAP* POS 1: 0% FLAP* POS 2: 100% FLAP* SPEED 2.0

25% Elevator 35% Elevator

Twin Otter 1.2m

Battery Installation and ESC ArmingBattery SelectionA 3S 2200-3200mAh LiPo battery is required. Refer to the Optional Parts List for battery recommendations. If using a battery other than those listed, the battery should be within the range of capacity, dimensions and weight of the Spektrum Li-Po battery pack to fit in the fuselage.CAUTION: Add nose weight for lighter batteries. Always verify the model balances within the recommended CG range before flying. Attempting to fly the model with an aft CG will cause the model to be unstable.CAUTION: Never adjust the CG while a battery is connected.CAUTION: When replacing the wheels with floats, recheck the CG. Place the battery further forward to compensate for the CG change.1. For added security, apply the loop side (soft side) of the optional hook and loop tape to the bottom of your battery, and the hook side to the battery tray.2. Remove the battery hatch. 3. Install the fully charged battery in the center of the battery compartment asshown. Secure using the hook and loop straps. 4. Connect the battery to the ESC. Two beeps indicate the ESCs are armed.CAUTION: Always keep hands away from the propeller. When armed, the motor will turn the propeller in response to any throttle movement.5. Keep the aircraft immobile and away from wind or the system will not initialize. · The motor will emit two even tones when the battery is connected and the ESC has a throttle signal. · The receiver LED will illuminate orange when it is initialized. · Fast continuous beeps indicate the ESCs are not armed.6. Reinstall the battery hatch.

ESC Error Tone

Tone Meaning

Continuously repeating single tone

Abnormal throttle signal Throttle signal not at low position

Center of GravityThe Center of Gravity (CG) location is measured from the leading edge of the wing at the root. The CG will be affected by cargo or battery changes. Always verify the CG is within the recommended range before flight.IMPORTANT: Place the CG 45mm (±5mm) from the leading edge.CAUTION: Install the battery but do not arm the ESC while checking the CG. Personal injury may result.

ENPossible problem Transmitter and receiver not bound Throttle lead damaged or not plugged into receiver Throttle lead plugged into receiver backward Throttle stick not at low position Throttle reversed Throttle trim raised45mm ±5mmback from leading edge of wing at the fuselage.

Transmitter and Receiver Binding / Switching ON and OFF SAFE Select (BNF Basic)

This product requires an approved SpektrumTM DSM2®/DSMX® compatible transmitter. Visit www.bindnfly.com for a complete list of approved transmitters.The aircraft has an optional SAFE Select feature, which can be switched ON or OFF easily by binding in a specific manner as described below.IMPORTANT: Before binding a transmitter, read the Transmitter Setup section of this manual to ensure that your transmitter is properly programmed for this aircraft.

Bind Plug Installation

BIND PLUG

Switching ON SAFE Select Binding Sequence

Switching OFF SAFE Select Binding Sequence

Install Bind Plug

Remove Bind Plug

RX in Bind Mode

Bind TX to RX

Install Bind Plug

Bind TX to RX RX in Bind Mode

Remove Bind Plug

Binding Procedure / Switching ON SAFE Select

Binding Procedure / Switching OFF SAFE Select

IMPORTANT: The included AR631 receiver has been programmed for operation specifically for this aircraft. Refer to the receiver manual for correct setup if the receiver is replaced or is used in another aircraft.

CAUTION: When using a Futaba® transmitter with a Spektrum DSM® module, you must reverse the throttle channel and rebind. Refer to your Spektrum module manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.

CAUTION: When using a Futaba® transmitter with a Spektrum DSM module, you must reverse the throttle channel and rebind. Refer to your Spektrum module manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.

1. Move the transmitter controls to neutral (flight controls: rudder, elevators and ailerons) or to low positions (throttle, throttle trim).*

2. Install a bind plug in the receiver bind port.

3. Place the aircraft level on its wheels, then connect the flight battery to the ESC. The motor will produce a series of sounds. The orange bind LED on the receiver will begin to flash rapidly.4. Remove the bind plug from the bind port.5. Take three steps away from the aircraft /receiver and then put the transmitter in bind mode. Refer to your transmitter’s manual for specific binding instructions. IMPORTANT: Do not point the transmitter’s antenna directly at the receiver while binding. IMPORTANT: Keep away from large metal objects while binding.6. The receiver is bound to the transmitter when the orange bind light on the receiver stays orange. The ESC will produce a series of sounds. The tones indicate the ESC is armed, provided the throttle stick and throttle trim are low enough to trigger arming.

3. Place the aircraft level on its wheels, then connect the flight battery to the ESC. The motor will produce a series of sounds. The orange bind LED on the receiver will begin to flash rapidly. DO NOT remove the bind plug at this time.4. Take three steps away from the aircraft /receiver and then put the transmitter in bind mode. Refer to your transmitter’s manual for specific binding instructions. IMPORTANT: Do not point the transmitter’s antenna directly at the receiver while binding. IMPORTANT: Keep away from large metal objects while binding.5. The receiver is bound to the transmitter when the orange bind light on the receiver stays orange. The ESC will produce a series of sounds. The tones indicate the ESC is armed, provided the throttle stick and throttle trim are low enough to trigger arming.6. Remove the bind plug from the bind port.

IMPORTANT: Once bound, the receiver will retain its bind settings for that transmitter until it has been intentionally changed, even when power is cycled ON and OFF. Repeat the binding process as necessary.SAFE Select ON Indication Every time the receiver is powered ON the surfaces will cycle back and forth twice with a slight pause at neutral position to indicate that SAFE Select is switched ON.

IMPORTANT: Once bound, the receiver will retain its bind settings for that transmitter until it has been intentionally changed, even when power is cycled ON and OFF. Repeat the binding process as necessary.SAFE Select OFF Indication Every time the receiver is powered ON the surfaces will cycle back and forth once to indicate that SAFE Select has been switched OFF.

The throttle will not arm if the transmitter’s throttle control is not put at the lowest position. If problems are encountered, follow the binding instructions and refer to the transmitter troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Product Support office.

*Failsafe If the receiver loses transmitter communication, the failsafe will activate. When activated, failsafe moves the throttle channel to its preset failsafe position (low throttle) that was set during binding. All other channels move to actively level the aircraft in a descending turn.

Twin Otter 1.2m

SAFE® Select Switch DesignationSAFE® Select technology can be assigned to any open switch (2 or 3 position) controlling a channel (59) on your transmitter. Once assigned to a switch, SAFE select ON gives you the flexibility to choose SAFE technology or AS3X mode while in flight. If the aircraft is bound with SAFE select OFF, the aircraft will be in AS3X mode exclusively.IMPORTANT: Before assigning your desired switch, ensure that the travel for that channel is set at 100% in both directions and the aileron, elevator, rudder and throttle are all on high rate with the travel at 100%.CAUTION: Keep all body parts well clear of the propeller and keep the aircraft securely restrained in case of accidental throttle activation.TIP: SAFE Select is assignable on any unused channels 59. See your transmitter manual for more information about assigning a switch to a channel.TIP: Use your radio channel monitor to confirm that the four primary channels are showing 100% travel while assigning the switch.TIP: Use the channel monitor to make sure the switch you are assigning for SAFE Select is active and driving a channel between 5-9 and that it is traveling 100% in each direction.TIP: Make sure your four primary channels are not reversed if you are having trouble assigning a SAFE Select switch.Control Surface CenteringAfter assembly and transmitter setup, confirm that the control surfaces are centered. The model must be powered up bound to the transmitter in AS3X mode, with the throttle left at zero. When enabled, SAFE mode is active at power up. AS3X mode is activated when the throttle is raised above 25% for the first time after being powered on. It is normal for the control surfaces to respond to aircraft movement if the aircraft is in AS3X or SAFE modes.1. Verify the trims and subtrims on your transmitter are 0.2. Power up the model in AS3X mode and leave the throttle at 0.3. Verify the control surface tips are mechanically centered.

Assigning a Switch1. Bind the aircraft to choose SAFE Select ON. This will

Mode 1 and 2 Transmitters

allow the system to be assigned to a switch.

2. Hold both transmitter sticks to the inside bottom corners and toggle the desired switch 5 times (1 toggle = full up and down) to assign that switch. The control surfaces of the aircraft will move, indicating the switch has been selected.

100%X 5100%

Repeat the process to assign a different switch or to deactivate the current switch if desired.

4. If you need to make an adjustment, rotate the clevis on the linkage to alter the linkage length between the servo arm and the control horn.After binding a transmitter to the aircraft receiver, set the trims and sub-trims to 0, then adjust the clevises to center the control surfaces.5. Center the elevator approximately 3mm down from neutral for level flight.

3mm

ENControl Surface DirectionPower on the transmitter and connect the battery. Use the transmitter to operate the aileron and elevator controls. View the aircraft from the rear when checking the control directions. Ailerons1. Move the aileron stick to the left. The right aileron should move down and the left aileron up, which will cause the aircraft to bank left.2. Move the aileron stick to the right. The right aileron should move up and the left aileron down, which will cause the aircraft to bank right.Elevators 1. Pull the elevator stick back. The elevators should move up, which will cause the aircraft to pitch up. 2. Push the elevator stick forward. The elevators should move down, which will cause the aircraft to pitch down.

Aileron stick Elevator stick

Rudder 1. Move the rudder stick to the left. The rudder should move to the left, which will cause the aircraft to yaw left.2. Move the rudder stick to the right. The rudder should move to the right, which will cause the aircraft to yaw right.

Rudder stick

Dual Rates and Control ThrowsProgram your transmitter to set the rates and control throws based on your experience level. After flying, you may choose to adjust the values for the desired control response.

Aileron Elevator RudderFlap Travel

The table to the right shows the factory settings for the control horns and servo arms. These settings, in conjunction with the low rate transmitter settings, are intended for intermediate level pilots to help ensure a successful flight.Fly the aircraft at these factory settings before making changes.

Aileron Elevator RudderFlaps

Low Rate

8mm

10mm

Half q = 10mm Full q = 20mm

High Rate 12mm 12mm 20mm

Horns

Arms

Nose Wheel

Twin Otter 1.2m

AS3X Control Direction Test (BNF)This test ensures that the AS3X® control system is functioning properly. Assemble the aircraft and bind your transmitter to the receiver before performing this test.1. Raise the throttle just above 25%, then lower the throttle to activate AS3X technology.CAUTION: Keep all body parts, hair and loose clothing away from a moving propeller, as these items could become entangled.2. Move the entire aircraft as shown and ensure the control surfaces move in the direction indicated in the graphic. If the control surfaces do not respond as shown, do not fly the aircraft. Refer to the receiver manual for more information.Once the AS3X system is active, control surfaces may move rapidly. This is normal. AS3X remains active until the battery is disconnected.

Elevator

Aircraft movement

ENAS3X Reaction

Aileron

Rudder

In Flight Trimming (BNF)During your first flight, trim the aircraft for level flight at 1/2 throttle with flaps up. Make small trim adjustments with your transmitter’s trim switches to straighten the aircraft’s flight path.After adjusting the trim, do not touch the control sticks for 3 seconds. This allows the receiver to learn the correct settings to optimize AS3X performance. Failure to do so could affect flight performance.

3 Seconds

Flying Tips and RepairsConsult local laws and ordinances before choosing a flying location.Getting StartedBefore you fly, range check the radio system. Refer to your specific transmitter instruction manual for range test information. When you first connect the battery to the airplane AS3X will not be active. After advancing the throttle the first time, the AS3X system will be active and it is normal to see the control surfaces react to aircraft movement. For your first flights set your transmitter timer or a stopwatch to 5 minutes. Adjust your timer for longer or shorter flights once you have flown the model.TakeoffFace the aircraft into the wind for takeoff. Set your transmitter to low rates and drop the flaps to takeoff position (half position). Flaps are not required, but lowering them makes takeoffs shorter.Gradually increase the throttle to full, and steer on the ground with rudder as necessary to keep the aircraft rolling straight. Be aware the nose wheel will become more sensitive as speed increases. Leave the elevator at neutral and allow the aircraft to accelerate up to speed on the ground, then pull up gently on the elevator to rotate for takeoff. When airborne, climb to a comfortable altitude, and return the flaps to the level position.FlyingFor your first flights climb to a moderate altitude and get comfortable with the aircraft while the battery is fresh. Get a feel for the aircraft’s low speed performance with the flaps up and down at a safe altitude (approximately 100 feet or more) before being required to make your first landing attempt. Land the aircraft when the timer expires. If at any time the motor power reduces, land the aircraft immediately to recharge the flight battery. See the Low Voltage Cutoff (LVC) section for more details on maximizing battery health and run time.LandingPlan to land the aircraft into the wind when possible. Fly downwind and turn into the wind to begin the approach. Lower the throttle and lower the flaps to the landing position (full down position.) Flaps will make the landing approach steeper and slower, and allow for a smoother landing. If there is a significant crosswind, only lower the flaps to the takeoff position (middle position) which will help maintain speed and better directional control during approach.During the approach and descent, keep the wings level and the aircraft pointed into the wind. The angle of attack (the angle between the aircraft’s pitch attitude and the horizon) should remain consistent and slightly nose high during the decent. With the angle of attack maintained during the descent, the speed and descent rate is mostly controlled with small throttle changes. Stay into the throttle to maintain speed and control during decent until the aircraft is ready to flare. As the airplane descends into ground effect, fully lower the throttle, pull the nose up more to bleed off airspeed (flare), and the aircraft will settle on its wheels.

Once on the ground leave the elevator neutral and avoid sharp turns until the plane has slowed enough to prevent scraping the wingtips.NOTICE: If a crash is imminent, reduce the throttle and trim fully. Failure to do so could result in extra damage to the airframe, as well as damage to the ESC and motor.NOTICE: After any impact, always ensure the receiver is secure in the fuselage. If you replace the receiver, install the new receiver in the same orientation as the original receiver or damage may result.NOTICE: Crash damage is not covered under warranty.NOTICE: When you are finished flying, never leave the aircraft in direct sunlight or in a hot, enclosed area such as a car. Doing so can damage the aircraft.Low Voltage Cutoff (LVC)When a Li-Po battery is discharged too much per cell, it will not hold a charge. The ESC protects the flight battery from over-discharge using Low Voltage Cutoff (LVC). Before the battery charge decreases too much, LVC removes power supplied to the motor. Power to the motor reduces, showing that some battery power is reserved for flight control and safe landing.Disconnect and remove the Li-Po battery from the aircraft after use to prevent trickle discharge. Charge your Li-Po battery to about half capacity before storage. During storage, make sure the battery charge does not fall below 3V per cell. LVC does not prevent the battery from over-discharge during storage.NOTICE: Repeated flying to LVC will damage the battery.Tip: Monitor your aircraft battery’s voltage before and after flying by using a Li-Po Cell Voltage Checker (SPMXBC100, sold separately).OscillationFor most flight maneuvers the aircraft should fly smoothly and normal, but it is possible in some flight conditions you may see oscillation (the aircraft rocks back and forth on one axis due to overcontrol). If oscillation occurs, refer to the Troubleshooting Guide for more information.RepairsThanks to the EPO foam material in this aircraft, repairs to the foam can be made using virtually any adhesive (hot glue, regular CA, epoxy, etc). When parts are not repairable, see the Replacement Parts List for ordering by item number. For a listing of all replacement and optional parts, refer to the list at the end of this manual.NOTICE: Use of CA accelerant on your aircraft can damage paint. DO NOT handle the aircraft until accelerant fully dries.

SAFE Select Flying TipsWhen flying in SAFE Select mode the aircraft will return to level flight any time the aileron and elevator controls are at neutral. Applying aileron or elevator control will cause the airplane to bank, climb or dive, and the amount the stick is moved will determine the attitude the airplane flies. Holding full control will push the aircraft to the pre-determined bank and roll limits but it will not go past those angles.When flying with SAFE Select it is normal to hold the control stick deflected with moderate aileron input when flying through a turn. To fly smoothly with SAFE Select avoid making frequent control changes and don’t attempt to correct for minor deviations. With SAFE Select, holding deliberate control inputs will command the aircraft to fly at a specific angle and the model will make all corrections to maintain that flight attitude.Return the elevator and aileron controls to neutral before switching from SAFE Select mode to AS3X mode. If you do not neutralize controls when switching into AS3X mode, the control inputs used for SAFE Select mode will be excessive for AS3X mode and the aircraft will react immediately.

Differences between SAFE Select and AS3X modesThis section is generally accurate but does not take into account flight speed, battery charge status, and many other limiting factors.· In SAFE Select mode the aircraft will self level when the control stick is neutralized. In AS3X mode the aircraft will continue to fly at its present attitude when the control stick is neutralized.· In SAFE Select mode holding a small amount of control will result in the model banking or pitching to a moderate angle and remaining at that angle as long as the control stick doesn’t move. In AS3X mode holding a small amount of control will result in the model continuing to pitch or roll at a slow rate as long as the control stick doesn’t move.· In SAFE Select mode holding full control will result in the airplane banking or pitching to the predetermined limits and the aircraft will keep flying at that attitude as long as the control stick is fully deflected. In AS3X mode holding full control will result in the aircraft pitching or rolling as fast as possible, and it will continue to rapidly change attitude as long as the control stick is fully deflected.

Twin Otter 1.2m

Post Flight1 Disconnect the flight battery from the ESC (Required for Safety and battery life). 2 Power OFF the transmitter. 3 Remove the flight battery from the aircraft. 4 Recharge the flight battery.

5 Repair or replace all damaged parts. 6 Store the flight battery apart from the aircraft and monitor the battery charge. 7 Make note of flight conditions and flight plan results, planning for future flights.

Motor ServiceCAUTION: Always disconnect the flight battery before performing motor service.Disassembly1. Remove the spinner screw and spinner from the propeller shaft. 2. Remove the propeller nut. The right propeller nut for prop T7056CR is reverserotation. 3. Remove the propeller. 4. Remove the two screws from the sides of the cowling and remove the cowlingfrom the nacelle. 5. Remove top and bottom set screws. 6. Disconnect the motor wires from the ESC wires. 7. Remove the motor from the X-mount.AssemblyAssemble in reverse order.· Correctly align and connect the motor wire colors with the ESC wires. · Install the propeller as shown. · Tighten the spinner nut to secure the propeller into place.

T7056CR

T7056C

Float Assembly and Installation1. Remove the screw on the bottom of the fuselage, and remove the landing gear cover.2. Loosen the nose wheel assembly screw, and remove the nose wheel assembly from the nose wheel steering bracket.3. Loosen the six 2mm x 10mm mounting screws from the landing gear mounting clamps. Remove the mounting clamps (screws attached) and set them aside.4. Install the front and rear float struts in the fuselage. The float struts angle down at the ends; the wheel strut is straight out, away from the plane.5. Reinstall the landing gear cover and tighten the fuselage screw.6. Install the floats and the spreader bars onto the struts, using the plastic clamps and the 2mm x 10mm screws to secure each clamp.7. Install the steering wire, slipping the z-bend into the steering arm and snapping the rear clip into the water rudder clevis.8. Secure the pushrod sleeve to the rear spreader bar with the included zip tie.Tip: If you removed the steering arm for the water rudder for flying with wheels, reinstall it for flying with floats.Disassemble in reverse order.NOTICE: If installing floats, always recheck the center of gravity before attempting to fly. Failure to do so may result in a crash.

Flying Off WaterFlying off water poses a higher risk because piloting errors or water conditions can cause the aircraft to become stranded. Only fly from the water when a level of comfort has been achieved flying the aircraft from the ground.Pre-FlightEnsure the optional floats are secure on the fuselage and the water rudder is correctly connected and operating with the main rudder before putting the aircraft in the water. Select an area to fly that does not have water currents, salt water, or debris. Look around the flight area and be aware of trees, docks, buoys, or other obstacles. Always fly with a spotter and avoid swimmers, boaters, people fishing, and people on the beach.TaxiingWhen taxiing, use low throttle settings and the rudders to steer. Hold up elevator to help keep the rudder in the water and the nose of the floats above the surface. Steer into the wind when turning, and crab into the wind if crosswind taxiing is required. When turning or crabbing into the wind, apply aileron against the wind to keep the upwind side of the wing down and prevent the aircraft from being flipped over. Do not apply down elevator when the airplane is taxiing or during the takeoff run.On StepWhen speed increases with throttle, the floats will rise out of the water and begin to plane on the surface of the water, riding “on step.” The floats will come on step at a speed below flight speed, this is a transitional phase when the aircraft is not up to flight speed yet. This is considered a high speed taxi. Do not attempt to take off as soon as the aircraft comes on step. Use low to medium throttle and hold up elevator to manage speed on the water during a high speed taxi.

TakeoffTo lift off from the water, set the flaps to the takeoff position, hold up elevator and accelerate the aircraft to bring it on step. Relax the up elevator as the airplane comes on step and accelerate to flight speed with full throttle. When the aircraft is travelling at a sufficient speed, pull back slightly on the elevator to rotate for liftoff.LandingTo land on the water, set the flaps to the landing position, and fly into the wind. Reduce the throttle to a low setting but keep some power during the approach. As the aircraft settles into ground effect, reduce the throttle fully and hold up elevator to flare. Hold up elevator through the touch down and as the airplane decelerates on the water.WARNING: Never attempt to retrieve a downed aircraft by swimming unless you are sufficiently trained and/or there is another person available to respond in the case of an emergency.CAUTION: Have a plan for retrieval in the event the airplane becomes stranded. Never retrieve a downed model in the water alone.CAUTION: If at any time water splashes in the fuselage while flying from water, bring the airplane to shore, open the battery hatch and immediately remove any water that may have gotten in the fuselage. Leave the battery hatch open overnight to let the inside dry out and to prevent moisture damage to the electronic components. Failure to do so could cause the electronic components to fail, which could result in a crash.TIP: Use a fishing pole with heavy line as a retrieval tool. Attach a tennis ball to the line, and throw the ball past a stranded aircraft to retrieve it.

Twin Otter 1.2m

Replacement Parts

Part Number

Description

EFL30051 Fuselage: Twin Otter

EFL300511 Wheels: Twin Otter

EFL300512 Battery Hatch: Twin Otter

EFL300513 Hardware Set: Twin Otter

EFL300516 Decal Sheet: Twin Otter

EFL30052 Wing: Twin Otter

EFL30053 Horizontal Stabilizer: Twin Otter

EFL30054 Nacelles: Twin Otter

EFL30055 Cowlings: Twin Otter

EFL30058 Landing Gear Set: Twin Otter

EFL30059 Float Set: Twin Otter

EFLA300515 ESC 20A: Twin Otter

EFLA300517 Spinner Set: Twin Otter

EFLM300514 2210-1350 Motor: Twin Otter

EFLP30056 Propeller CW 7 x 5.6 x 3: Twin Otter

EFLP30060 Propeller CCW 7 x 5.6 x 3: Twin Otter

SPMAR631 AR631 6-Ch AS3X Sport Receiver

SPMSA330R 9 Gram Servo Reversed

Optional Parts

Part Number

Description

SPMA3065

AS3X Programming Cable – USB Interface

SPMBT1000 AS3X Bluetooth Programming Module

SPMXBC100 SMART Battery Checker and Servo Driver

DYN1405

Li-Po Charge Protection Bag, Large

DYN1400

Li-Po Charge Protection Bag, Small

SPMR6750

DX6 Transmitter Only MD2 G3

SPMR6775

NX6 6-Channel Transmitter Only

SPMR8000

DX8 Transmitter Only MD2

SPMR8100

DX8e 8CH Transmitter Only

SPMR8200

NX8 8-Channel Transmitter Only

SPMR9910

DX9 Black Transmitter Only MD2

SPMR10100 NX10 10 Channel Transmitter Only

SPMR12000 iX12 12 Channel Transmitter Only

SPMX32003S30 11.1V 3200mAh 3S 30C Smart LiPo, IC3

SPMXC1000 Smart S1200 DC Charger, 1x200W

SPMXC1010 Smart S2100 AC Charger, 2x100W

Recommended Receivers (PNP)

Part Number

Description

SPMAR620 AR620 6-Channel Sport Air Receiver Telemetry Equipped Receivers SPMAR6600T AR6600T 6-Channel Air Integrated Telemetry Receiver SPMAR6270T AR6270T 6-Channel Carbon Fuse Integrated Telemetry Receiver SPMAR8010T AR8010T 8-Channel Air Integrated Telemetry Receiver SPMAR9030T AR9030T 9-Channel Air Integrated Telemetry Receiver AS3X Equipped Receivers SPMAR631 AR631 6-Channel AS3X Sport Receiver AS3X and Telemetry Equipped Receivers SPMAR7350 AR7350 7-Channel AS3X Receiver with Integrated Telemetry SPMAR9350 AR9350 9-Channel AS3X Receiver with Integrated Telemetry Telemetry Sensors* SPMA9574 Aircraft Telemetry Airspeed Indicator SPMA9589 Aircraft Telemetry Altitude and Variometer Sensor SPMA9558 Brushless RPM Sensor SPMA9605 Aircraft Telemetry Flight Pack Battery Energy Sensor SPMA9587 Aircraft Telemetry GPS Sensor

*Not compatible with BNF, Telemetry receiver required

AMA National Model Aircraft Safety Code

Effective January 1, 2018

A model aircraft is a non-human-carrying device capable of sustained flight within visual line of sight of the pilot or spotter(s). It may not exceed limitations of this code

and is intended exclusively for sport, recreation, education and/or competition. All model flights must be conducted in accordance with this safety code and related AMA

guidelines, any additional rules specific to the flying site, as well as all applicable laws and regulations.

As an AMA member I agree:

· I will not fly a model aircraft in a careless or reckless manner.

Advanced Flight System programming.

· I will not interfere with and will yield the right of way to all human-carrying

· I will only fly models weighing more than 55 pounds, including fuel, if certified

aircraftusing AMA’s See and Avoid Guidance and a spotter when appropriate.

through AMA’s Large Model Airplane Program.

· I will not operate any model aircraft while I am under the influence of alcohol or · I will only fly a turbine-powered model aircraft in compliance with AMA’s Gas

any drug that could adversely affect my ability to safely control the model.

Turbine Program.

· I will avoid flying directly over unprotected people, moving vehicles, and

· I will not fly a powered model outdoors closer than 25 feet to any individual,

occupied structures.

except for myself or my helper(s) located at the flightline, unless I am taking off

· I will fly Free Flight (FF) and Control Line (CL) models in compliance with AMA’s

and landing, or as otherwise provided in AMA’s Competition Regulation.

safety programming.

· I will use an established safety line to separate all model aircraft operations

· I will maintain visual contact of an RC model aircraft without enhancement other

from spectators and bystanders.

than corrective lenses prescribed to me. When using an advanced flight system,

such as an autopilot, or flying First-Person View (FPV), I will comply with AMA’s

Twin Otter 1.2m

Troubleshooting Guide AS3X

ProblemOscillationInconsistent flight performance Incorrect response to the AS3X Control Direction Test

Possible Cause Damaged propeller or spinner Imbalanced propeller Motor vibration Loose receiver Loose aircraft controls Worn parts Irregular servo movement Trim is not at neutral Sub-Trim is not at neutral Aircraft was not kept immobile for 5 seconds after battery connectionIncorrect direction settings in the receiver, which can cause a crash

Solution Replace propeller or spinner Balance the propeller Replace parts or correctly align all parts and tighten fasteners as needed Align and secure receiver in fuselage Tighten or otherwise secure parts (servo, arm, linkage, horn and control surface) Replace worn parts (especially propeller, spinner or servo) Replace servo If you adjust trim more than 8 clicks, adjust the clevis to remove trim No Sub-Trim is allowed. Adjust the servo linkage With the throttle stick in lowest position. Disconnect battery, then reconnect battery and keep the aircraft still for 5 secondsDO NOT fly. Correct the direction settings (refer to the receiver manual), then fly

Troubleshooting Guide

ProblemAircraft will not respond to throttle but responds to other controlsExtra propeller noise or extra vibrationReduced flight time or aircraft underpowered

Possible CauseThrottle not at idle and/or throttle trim too high Throttle servo travel is lower than 100% Throttle channel is reversed Motor disconnected from ESC Damaged propeller and spinner, collet or motor Propeller is out of balance Prop nut is too loose Flight battery charge is low Propeller installed backwards Flight battery damaged Flight conditions may be too cold Battery capacity too low for flight conditions

Transmitter too near aircraft during binding process

Aircraft will not Bind (during binding) to transmitter

Aircraft or transmitter is too close to large metal object, wireless source or another transmitterThe bind plug is not installed correctly in the bind portFlight battery/transmitter battery charge is too lowBind switch or button not held long enough during bind process

Transmitter too near aircraft during connecting process

Aircraft will not connect (after binding) to transmitterControl surface does not moveControls reversed Motor power pulses then motor loses power

Aircraft or transmitter is too close to large metal object, wireless source or another transmitter Bind plug left installed in bind port Aircraft bound to different model memory (ModelMatchTM radios only) Flight battery/Transmitter battery charge is too low Transmitter may have been bound to a different aircraft using different DSM protocol Control surface, control horn, linkage or servo damage Wire damaged or connections loose Transmitter is not bound correctly or the incorrect airplanes was selected Flight battery charge is low BEC (Battery Elimination Circuit) of the ESC is damaged Transmitter settings are reversed ESC uses default soft Low Voltage Cutoff (LVC) Weather conditions might be too cold Battery is old, worn out, or damaged Battery C rating might be too small

SolutionReset controls with throttle stick and throttle trim at lowest setting Make sure throttle servo travel is 100% or greater Reverse throttle channel on transmitter Make sure motor is connected to the ESC Replace damaged parts Balance or replace propeller Tighten the prop nut Completely recharge flight battery Install propeller with numbers facing forward Replace flight battery and follow flight battery instructions Make sure battery is warm before use Replace battery or use a larger capacity battery Move powered transmitter a few feet from aircraft, disconnect and reconnect flight battery to aircraftMove aircraft and transmitter to another location and attempt binding againInstall bind plug in bind port and bind the aircraft to the transmitter Replace/recharge batteries Power off transmitter and repeat bind process. Hold transmitter bind button or switch until receiver is bound Move powered transmitter a few feet from aircraft, disconnect and reconnect flight battery to aircraftMove aircraft and transmitter to another location and attempt connecting againRebind transmitter to the aircraft and remove the bind plug before cycling powerSelect correct model memory on transmitterReplace/recharge batteriesBind aircraft to transmitterReplace or repair damaged parts and adjust controls Do a check of wires and connections, connect or replace as neededRe-bind or select correct airplanes in transmitterFully recharge flight battery Replace ESC Perform the Control Direction Test and adjust the transmitter controls appropriately Recharge flight battery or replace battery that is no longer performing Postpone flight until weather is warmer Replace battery Use recommended battery

Limited WarrantyWhat this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.What is Not Covered This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations, or (vii) use that violates any applicable laws, rules, or regulations.OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.Purchaser’s Remedy Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.Law These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.WARRANTY SERVICES Questions, Assistance, and Services Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon

to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www. horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.Inspection or Services If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby. com/content/service-center_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office.Warranty Requirements For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.Non-Warranty Service Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www. horizonhobby.com/content/service-center_render-service-center.ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.10/15

Contact Information

Country of PurchaseUnited States of AmericaEuropean Union

Horizon Hobby Horizon Service Center (Repairs and Repair Requests) Horizon Product Support (Product Technical Assistance)SalesHorizon Technischer Service Sales: Horizon Hobby GmbH

Contact Informationservicecenter.horizonhobby.com/ RequestForm/ 877-504-0233 800-338-4639 +49 (0) 4121 2655 100

Address2904 Research Rd Champaign, Illinois, 61822 USAHanskampring 9 D 22885 Barsbüttel, Germany

Twin Otter 1.2m

FCC InformationFCC ID: BRWSPMSR6200A Supplier’s Declaration of Conformity EFL Twin Otter 1.2m PNP/BNF BASIC (EFL30075, EFL300500) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.Horizon Hobby, LLC 2904 Research Rd., Champaign, IL 61822 Email: Web: HorizonHobby.com

IC InformationIC: 6157A-SPMSR6200A CAN ICES-3 (B)/NMB-3(B) This device contains license-exempt transmitter(s)/receivers(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following 2 conditions:

1. This device may not cause interference.2. This device must accept any interference, including interference that may cause undesired operation of the device.

Compliance Information for the European Union

EU Compliance Statement: EFL30075 Twin Otter 1.2m PNP: Hereby, Horizon Hobby, LLC declares that the device is in compliance with the following: EU EMC Directive 2014/30/EU.EFL300500 Twin Otter 1.2m BNF BASIC: Hereby, Horizon Hobby, LLC declares that the device is in compliance with the following: EU Radio Equipment Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: https://www.horizonhobby.com/content/support-rendercompliance.Wireless Frequency Range and Wireless Output Power: 2404 2476MHz 5.58dBm

EU Manufacturer of Record: Horizon Hobby, LLC 2904 Research Road Champaign, IL 61822 USAEU Importer of Record: Horizon Hobby, GmbH Hanskampring 9 22885 Barsbüttel GermanyWEEE NOTICE: This appliance is labeled in accordance with European Directive 2012/19/EU concerning waste of electrical and electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.

©2020 Horizon Hobby, LLC. E-flite, Plug-N-Play, Bind-N-Fly, BNF, the BNF logo, DSM, DSM2, DSMX, Spektrum AirWare, AS3X, DSM, DSM2, DSMX, SAFE, the SAFE logo,and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. All other trademarks, service marks and logos are property of their respective owners.US 8,672,726. US 9,056,667. US 9,753,457. US 10,078,329. US 9,930,567. US 10,419,970. www.horizonhobby.com/

EFL30050

Updated 10/20

report this ad

59818.2

References

[xyz-ips snippet=”download-snippet”]

Posted

2023-02-01

E-flite

admin

Tags:

_pdf, 1.2m, E-flite, Horizon, Twin Otter