Hall Sensor Gimbals 2.4GHz 16CH Internal Multiprotocol RF System OpenTX Radio Transmitter RC Drone
Introduction
Thank you for purchasing the Eachine TX16S 2.4g remote control system. The system is versatile and can be used by beginners and professionals. In order to ensure the correct and safe use of this product, please read this instruction manual carefully before use. Changes have been made due to a version upgrade. The information contained in this manual is subject to change without notice.TX16S remote control is suitable for all types of fixed-wing, glider, helicopter, boats, robotics, multi-rotor aircraft and more. The model type can be selected according to the aircraft used, and various hybrid functions can be used.Sincerely, The Eachine Team.
Safety instructions.
Many remote control models are equipped with powerful motors and sharp propellers. Use caution when operating models. When assembling or maintaining, make sure the model is powered off and the propeller is removed.
Do not operate the TX16S remote control system under the following conditions:
- In severe weather or strong wind conditions, such as rain, hail, snow, storm or electromagnetic environment.
- Under any circumstances where visibility is limited.
- In areas where people, property, high-voltage power lines, public roads, vehicles or animals may be present.
- If you feel tired or unwell, or under the influence of drugs or alcohol.
- If the remote control or model appears to be damaged or not working properly.
- In areas where 2.4GHz interference is high or where 2.4GHz radios are prohibited.
- When the battery voltage is too low to use.
- In areas where local regulations prohibit the use of aviation models.
Manuals and firmware downloads.TX16S comes pre-installed with standard OpenTX firmware. To download the latest software manual, visit the Eachine website: https://www.eachine.com/
Important！The TX16S is shipped with the most stable firmware at the time of manufacture. Please only update firmware if you are experienced and confident in updating system firmware. Incorrect updates may render the radio inoperable.
Remote control overview
Model selection and protocol selection
TX16S comes with a 4-in-1 multi-protocol high-frequency module, which is compatible with many different protocols. To view the latest list of all compatible protocols, please visit:https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md.Please note that new protocols are constantly updated and added to the latest firmware, and some new protocols may require firmware upgrades.
press the MDL button to enter the MODEL settings, select MULTI in the MODEL SETUP page, and select the protocol you want to use in the sub-options. According to the RF protocol you choose, the system will automatically open the corresponding RF chip aboard the internal RF module while shutting down the other three RF chips that are not in use. Only one RF chip on the module will be switched on at a time to ensure that there is no interference from the unused RF chip.
- The Bind button is used to start the linking process.
- The Range button reduces power to 1/30 to facilitate testing of remote control distances.
Note: OpenTX software is very powerful and has a large number of programming and mixing functions. Please download the comprehensive software installation guide for more detailed instructions from the following link: https://www.open-tx.org
Specifications
Size: 286.9*128.9*183.8mmWeight: 750g (without battery)Transmission frequency: 2.400GHz-2.480GHzTransmitter module: Internal 4-in-1 multi-protocol module (CC2500 CYRF6936 A7105 NRF2401) Transmitting power: Max 22dbm (transmitting power is adjustable)Antenna gain: 2db (transmit power adjustable)Working current: 400mAWorking voltage: 6.6-8.4v DCRemote control distance:> 2km @ 22dbmOpen source firmware: OpenTX （remote control）DIY-Multiprotocol-TX-Module（Internal RF Firmware driven by Open TX）Channels: Up to 16 channels (depending on the receiver)Display: 4.3-inch TFT full-color display with a resolution of 480 * 272Gimbal: Non-contact 3D vector Hall with Aluminum facia. JR / FrSKY compatible module bracketUpgrade method: Support USB-C online / SD card offline upgradeProtocols: Full series DSM2 / X full series Flysky and Flysky 2A FrSKY(For a complete list of below link)https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md
Support.Warranty and Repairs.Please retain your proof of purchase and contact the retailer you purchased your TX16S from should you experience any problems with your radios hardware.
Firmware updates and OpenTX information.For latest news and firmware updates from the OpenTX please visit https://www.open-tx.org
User manualFor detailed user manual of TX16S OpenTX system firmware, please visit https://www.open-tx.org.
Important note on Power and charging precautions.The TX16S has built-in USB charging function for 2cell 7.4v Battery packs (2 x 3.7v Lithium cell packs). The charging circuit is only suitable for 2x 3.7v lithium-ion 18650, 2 x 21700 3.7v lithiumion (21700 2s 7.4v Lithium-Ion pack) or 2x 3.7v Lipoly batteries (2s 7.4v Lipo battery pack). The nominal battery voltage per cell is 3.7v and the maximum charging cut off voltage is 4.2v per cell.
Approved for use
2x 3.7v Li-ION 18650 cells (7.4v using supplied tray)2 x 3.7v Li-ION 21700 cells (Assembled as 7.4v 2s Battery pack)2 x 3.7v Lithium-polymere cells (Assembled as 7.4v 2s Battery pack)
DO NOT use3.6v Li-ION cells2S 6.6v LiFE Battery packsLiFEP04 cells
Do not use 2s 6.6v LiFE battery pack, 18650 lithium-ion cells with a nominal voltage of 3.6v or LiFEP04 18650 Round cells. Using the built in USB charger with incorrect battery types and voltage may cause damage to the remote control or fire.Check the health and condition of the batteries regularly. Do not use damaged cells. Never charge your device unattended. Always charge in a safe area away from flammable materials. If the remote control gets wet or damaged in any way, do not charge it.Eachine is not responsible for any adverse consequences caused by using or misusing this device.
EU Simple Declaration of ConformityRadioMaster declares the radio equipment TX16s is in compliance with EU directives Directive 2014/53/EU. Full text of the declaration of conformity is available at the following website https://www.eachine.com/Manufacturer byShenZhen RadioMaster Co., Ltd5th Floor, Yutian Building, No. 18 Yangtian Road, Xin’an Street, Baoan District, Shenzhen, Guangdong.FCC ID: 2AV3G-TX16S
FCC Information
This equipment has been tested and found to comply with the limits for Part 15 of the FCCrules. This device complies with part 15 of the FCC rules.Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Full text of the declaration of conformity is available at the following website https://www.ea-chine.com/
CAUTION:Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
Antenna Separation DistanceWhen operating your Eachine transmitter, please be sure to maintain a separation distance ofat least 20 cm between your body (excluding fingers, hands, wrists, ankles and feet) and the antenna to meet RF exposure safety requirements as determined by FCC regulations.
References
[xyz-ips snippet=”download-snippet”]