Earthquake 5 Ton Electric Log Splitter Owner’s Manual

Earthquake 5 Ton Electric Log Splitter Owner’s Manual

STOP! ACTIVATE YOUR WARRANTY BEFORE USE

All products must be registered within 30 days from the date of purchase in order to be covered under warranty. For more information regarding Warranty and Registration please review the Warranty and Registration terms and conditions expressed in the warranty insert.

INTRODUCTION

Thank you for purchasing your product from Earthquake®. We have worked to ensure that this product meets the highest standards for usability and durability. With proper care, your purchase will provide many years of service. Please read this entire manual before installation and use. Earthquake® reserves the right to change, alter or improve the product and this document at any time without prior notice. Due to continuous product improvements, product images may not be exact. Some assembly may be required.Read and keep this manual for future reference. This manual contains important information regarding safety, assembly, operation and maintenance. The owner must be certain that all the product information is included with the unit. This information includes the manual, the replacement parts and the warranties. This information must be included to make sure state laws and other laws are followed. All persons to whom rent/loan this unit must have access to and understand this information. This manual shouldremain with the product even if it is resold.

REGISTRATION AND SERVICE

Record the product model number and serial number in the space provided for easy reference when ordering parts or requesting technical support. Excluding emissions-relatedwarranty items, the warranty is valid only if the completed registration is received by Ardisam within 30 days of purchase. You can register your warranty online by visitingwww.GetEarthquake.com, or by mailing it to: Ardisam, 1160 8th Avenue, Cumberland, WI 54829. You may also call our Customer Service department at (800) 345-6007 Mondays through Fridays from 8 a.m. to 5 p.m. CST.

SAFETY AND SAFETY RULES OWNER’S RESPONSIBILITY

Safe and effective use of the 5-ton electric log splitter is the owner’s responsibility.

• Read and follow all safety instructions.
• Maintain the log splitter according to directions and schedule, included in this Earthquake® Operator’s Manual.
• Check your log splitter before turning it on. Keep guards in place and in working order. Replace damaged, missing or failed parts before using it.
• Ensure that anyone who uses the log splitter is familiar with all controls and safety precautions.

SPECIAL MESSAGES

Your manual contains special messages to bring attention to potential safety concerns, machine damage, as well as helpful operating and servicing information. Please read all the information carefully to avoid injury and machine damage.

NOTE: General information is given throughout the manual that may help the operator perform the operation or service of the machine.

IMPORTANT SAFETY PRECAUTIONS

Please read this section carefully. Operate the electric log splitter according to the safety instructions and recommendations outlined here, and stated throughoutthe text. Anyone who uses this log splitter must read the instructions carefully and be familiar with the controls.

This symbol signifies important safety A instructions, which, if not followed could endanger your personal safety. Read and follow all instructions in this manual before attempting to operate this equipment.

• Do not transport the log splitter with the motor running.
• Dress appropriately when operating the log splitter. Always wear sturdy footwear. Do not wear sandals, sneakers, or open toed shoes, and never operate the log splitter withbare feet. Do not wear loose clothing or jewelry that may get caught in moving parts. Always wear safety goggles for eye protection. Everyday glasses have only impact resistant lenses and are not effective safety glasses.

WARNING

WARNING INDICATES A HAZARD WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR SERIOUS INJURY AND/ORPROPERTY DAMAGE

CAUTION

CAUTION INDICATES YOU CAN BE HURT OR YOUR EQUIPMENT DAMAGED IF THE SAFETY INSTRUCTIONS THATFOLLOW THIS SIGNAL WORD ARE NOT OBEYED.

IMPORTANT

INDICATES HELPFUL INFORMATION FOR PROPER ASSEMBLY, OPERATION, OR MAINTENANCE OF YOUR EQUIPMENT.

• Always pay full attention to the movement of the log pusher. Do not attempt to load the log onto the log splitter until the log pusher has come to a complete stop. Alwayskeep hands, feet, hair and loose clothing away from any moving parts on the log splitter.
• Do not allow children to operate this log splitter. Adults should not operate the log splitter without proper instruction.
• Do not operate any power equipment under the influence of drugs, alcohol, or any medication that could affect your ability to use the equipment properly.
• Always keep your work area clean and well lit.
• Keep all screws, nuts and bolts tight.
• Always inspect the logs to be split for nails or other foreign objects. The ends of the logs must be cut square. Branches must be cut off flush with the trunk.
• Do not over-reach. Keep proper footing and balance at all times. Never stand on the log splitter. Do not use the log splitter as a step.
• Do not operate the log splitter from ground level. Place log splitter at a comfortable height (24-32 inches), on a stable, flat, and level work surface where there is plenty of room for handling material. Fasten the log splitter to the work surface if it tends to slip, walk, or slide.
• Do not use the log splitter in wet or damp areas or expose it to rain.
• Never try to split logs larger than those indicated in the specifications table. Failure to do so may damage the machine. Do not use the log splitter for anything otherthan splitting logs. Do not force log through splitter.
• Never use an extension cord that is not rated for outdoor use. The cord should not be longer than 30 feet. The cord should be of a heavy-duty construction (12-10 AWG).
• Check that the electric circuit is adequately protected and corresponds with the power, voltage and frequency of the motor. Check that there is a ground connection and a regulation differential switch upstream. Ground the log splitter. Prevent body contact with ground surfaces: pipes, radiatiors, ranges, refrigerator enclosures, etc. Never open the pushbutton box on the motor. Make sure your fingers do not touch the plug’s metal prongs when plugging in or unplugging the log splitter.
• Do not remove jammed logs with your hands. If an object becomes lodged in the ram, unplug electric motor before attempting to remove the foreign object.
• Do not use the log splitter in areas where fumes from paint, solvents, or flammable liquids pose a potential fire/ explosion hazard.
• Use only original equipment parts from Ardisam, Inc., including all nuts and bolts.
• Disconnect power by unplugging power cord when not in use, before making adjustments, changing parts, cleaning, or working on the log splitter.
• Maintain and keep the log splitter clean for the best and safest performance.

STEPS FOR WORKING ON ELECTRIC LOG SPLITTER

1.  Turn off motor switch. Unplug motor.
2. Replace or repair the part on the log splitter.
3. Check all parts that were repaired, or removed during repair, to ensure they are secure and fit correctly

NOTE: All repair parts must come from the factory. Never replace parts that are not specifically designed for this log splitter

SPECIFICATIONS AND ELECTRICAL REQUIREMENTS

APPLICATION CONDITIONS

The Earthquake® 5-Ton Electric Log Splitter has been designed as a home use model only. It is designed for operating at ambient temperatures between 40° F. and 105° F. Thelog splitter can be stored or transported under ambient temperatures between -10° F. and 130° F.

ELECTRICAL REQUIREMENTS

Connect the main leads to a standard 11 OV ±10% electrical supply which has protection devices under-voltage, overvoltage, over-current, as well as a ground fault circuitinterrupter (GFCI) or a ground fault interrupter (GFI) with a maximum residual current of 0.03A.

SPECIFICATIONS

Model Number	32228	32229
Motor	120V~60Hz1500WIP54
Circuit Protection Requirements	20Amps(Amperes)
Log Capacity	Diameter*	2-10 inches
Length	20inches
Splitting Force	Ston
Hydraulic Pressure	2,300 psi
Hydraulic Oil Capacity	3.75 quarts
Overall Size	Length	40.Sin	49.0in
13.9in	37.0in	37.0in
Height	18.1 in	39.0 in
Weight	105Ib	135Ib

*Recommended diameter of the log – a small log can be difficult to split when it contains knobs or a particularly tough fiber. On the other hand, it may not be difficult to split logs with regular fibers even if its diameter exceeds the maximum diameter described in the specifications chart.

SET-UP AND PRE-OPERATION

      Figure 1

Before attempting to use, familiarize yourself with all the operating features and safety requirements of your log splitter.(SEE FIGURE 1)

1. Wedge                                                               8. 2-hand operating hydraulic control lever
2. Oil tank                                                             9 Safety guard for 2-hand  operating hydraulic control lever
3. Carrying handle                                                10. Log pusher
4. Supporting leg                                                  11. Log cradle
5. Motor w/push switch & circuit breaker
6. Rubber feet
7. Rolling wheel

Figure 2

WARNING

FOR YOUR OWN SAFETY, DO NOT CONNECT THE LOG SPLITTER TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL FOR YOUR OWN SAFETY, NEVER FORGET TO BOLT THEWHEEL BRACKET TO THE LOG SPLITTER, LIFT THE LOG SPLITTER BY THE HANDLES AT BOTH ENDS AND PLACE IT ON A 24-321N HIGH, STABLE, FLAT AND LEVEL WORK SURFACE. NEVER USE THE LOG SPLITTER IF IT IS NOT IN PERFECT ORDER OR IF IT NEEDS SERVICING. BEFORE STARTING WORK, CHECK CORRECT FUNCTIONING OF ALL THE CONTROLS (HYDRAULIC LEVER, PUSH BUTTON).

CAUTION

FAILURE TO LOOSEN THE BLEED SCREW WILL RESULT IN AIR BEING COMPRESSED AND DECOMPRESSED IN THE HYDRAULIC SYSTEM. CONTINUOUS AIR COMPRESSION AND DECOMPRESSION WILL BLOW OUT THE SEALS OF THE HYDRAULIC SYSTEM AND CAUSE PERMANENTDAMAGE TO THE LOG SPLITTER.

CAUTION

DO NOT ADJUST THE MAXIMUM PRESSURE LIMITING SCREW. THE PRESSURE LIMITING SCREW HAS BEEN SEALED ATTHE FACTORY TO PREVENT UNAUTHORIZED ADJUSTING. RESETTING THE SCREW WILL CAUSE THE HYDRAULIC PUMP TO FAIL TO OUTPUT ENOUGH SPLITTING PRESSURE OR CAUSE TOO MUCH PRESSURE, WHICH MAY RESULT IN SERIOUS INJURY, AS WELL AS DAMAGE TO THE MACHINE.

IMPORTANT

BEFORE OPERATING THE LOG SPLITTER, THE BLEED SCREW SHOULD BE LOOSENED BY 3-4 ROTATIONS SO AIR CAN GO IN AND OUT OF THE OIL TANK SMOOTHLY. AIR FLOWTHRU THE BLEED SCREW HOLE SHOULD BE DETECTABLE DURING LOG SPLITTER OPERATION. BEFORE MOVING THE LOG SPLITTER, MAKE SURE THE BLEED SCREW IS TIGHTENED TO AVOID OIL LEAKAGE FROM THIS POINT. (SEE FIGURE2)

ASSEMBLY

1. Install the wheels by inserting the axles into each leg.
2. Insert the hairpin into each of the axles. (SEE FIGURE 3) Figure 3

LOG SPLITTER OPERATION

The Earthquake® 5-Ton Electric Log Splitter requires the use of both hands to operate. The user’s left hand controls the hydraulic control lever, while the right hand controls the push button switch. The log splitter will freeze upon absence of either hand. The log pusher will return back to the starting position only after both hands release the controls. (SEE FIGURE4) Split the log in the direction of its grain. Placing logs across the log splitter for splitting is dangerous and may seriously damagethe machine. Do not attempt to split two logs at the same time. Figure4

FREEING A JAMMED LOG

1. Release both controls.
2. Once the log pusher completely stops at its starting position, insert a wood wedge under the jammed log. (SEE FIGURE 5)
3. Start the log splitter to push the wood wedge under the jammed log.
4. Repeat above procedure with sharper sloped wood wedges until the log is completely freed. Figure5

CAUTION

NEVER FORCE PRESSURE ON THE LOG SPLITTER FOR MORE THAN 5 SECONDS IN ORDER TO SPLITEXCESSIVELY HARD WOOD.

CAUTION

ALWAYS SET LOGS FIRMLY ON THE LOG CRADLE AND WORK TABLE. MAKE SURE LOGS WILL NOT TWIST, ROCK OR SLIP WHILE BEING SPLIT. DO NOT FORCE THE WEDGE BY SPLITTING THE UPPER PART OF THE LOG. THIS WILL BREAK THE WEDGE OR DAMAGE THEMACHINE. (SEE FIGURE 6)

CAUTION

DO NOT TRY TO KNOCK THE JAMMED LOG OFF THE WEDGE USING A HAMMER OR OTHER DEVICE. (SEE FIGURE 7)

                          Figure6

Figure 7

MAINTENANCE

REPLACING HYDRAULIC OIL

Replace the hydraulic oil in the log splitter after every 150 hours of use. Take the following steps to replace the oil.

1. Make sure all moving parts are stopped and the log splitter is unplugged.
2. Remove oil drain bolt and dipstick. Make sure bleed screw is closed tight. (SEE FIGURE 8)Figure 8
3. Turn the log splitter on the support leg side over using a one gallon or larger capacity container to drain the hydraulic oil. (SEE FIGURE 9)Figure 9
4. Turn the log splitter on the motor side. (SEE FIGURE 10)
5. Refill with 3.75 quarts of fresh hydraulic oil.
6. While keeping the log splitter vertical, clean the surface of dipstick on the oil drain bolt and put it back into the oil tank.
7. Make sure the level of the refilled oil is between the two grooves around the dipstick.
8. Clean the oil drain bolt before re-threading it back in. Make sure the bolt is tightened to avoid leakage before placing the log splitter horizontally

IMPORTANT: LOOSEN BLEED SCREW 3-4 TURNS BEFORE OPERATION.

Periodically check oil level to ensure it is between the two grooves around the dipstick. If the level is below the lower limit, fill until level is correct.The following hydraulic oils, or equivalent, are recommended for the log splitter’s hydraulic pump:SHELL Tellus 22MOBIL DTE 11ARA Vitam GF 22BP Energol HLP-HM 22

SHARPENING WEDGE

When the log splitter wedge becomes dull and/or worn, sharpen the wedge using a fine-toothed file and smooth any burrs or crushed areas along the cutting edge.

SERVICE, TROUBLESHOOTING AND REPAIR SERVICE INFORMATION

IMPORTANT

IN CASE OF A SERVICE PROBLEM, DO NOT SEND UNIT BACK TO RETAILER. CONTACT ARDISAM, INC., AT 1-800-345-6007, ANYTIME MONDAY THROUGH FRIDAY FROM 8 A.M. TO 5 P.M. WE WELCOME YOUR CALL.

In the event you experience trouble operating your log splitter, follow the suggestions in the troubleshooting guide in this section.The guide will help you pinpoint the causes of common problems and identify remedies. For more complicated repairs you may want to rely on your retailer, an authorized mechanic, or Ardisam, Inc. (Contact your retailer for a list of authorized mechanics in your area). A parts catalog is included in this section. We will always be glad to answer any questions you have, or help you find suitable assistance. To order parts or inquire about warranty, call or write us at the address found in the next column, under the section ordering repair parts.

ORDERING REPAIR PARTSParts can be obtained from the store where your log splitter was purchased or direct from the factory. To order from the factory, call or write to:

Please include the following information with your order:

1. Part numbers
2. Part description
3. Quantity
4. Model number and serial number

TROUBLESHOOTING

Get parts on line at www.GetEarthquake.com or Call 800-345-6007 M-F 8-5 CST

 

Read More About This Manual & Download PDF: