Einhell Self-Leveling Cross-Line Laser Instruction Manual

Table of Contents

Original operating instructionsSelf-Leveling Cross-Line Laser

Danger! – Read the operating instructions to reduce the risk of injury

DANGER!When using the equipment, a number of safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety information with due care. Keep these operating instructions in a safe place so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and the safety information as well. We cannot accept any liability for damage or accidents which arise due to failure to follow these instructions and the safety information.

Safety information

DANGER!Read all the safety information and instructions. Failure to adhere to the safety information and instructions set out below may result in electric shock, ﬁ re, and/or serious injury. Keep all the safety information and instructions in a safe place for future use. Special information about the laser

Caution: Laser radiation Do not look into the beam Laser class II

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.50, dated June 24/2007

Never look directly into the laser path.
Never direct the laser beam at reflecting surfaces or persons or animals. Even a low output laser beam can inflict injury on the eye.
Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Never open the laser module.
It is prohibited to carry out any modifications to the laser to increase its power.
The manufacturer cannot accept any liability for damage due to the non-observance of the safety information.

Safety information on the batteriesUse of the batteries

Inserting the batteries when the laser is switched on can cause accidents.
If the equipment is not used correctly, the batteries may leak. Avoid contact with the battery fluid. If you come into contact with battery fluid, clean the affected body part with running water. If you get battery fluid in your eyes, seek immediate medical assistance.
Escaped battery fluid can cause skin irritation and acid burns.
Never expose the batteries to excessive heat such as sunshine, fire, or similar.
Never recharge batteries that are not suitable for recharging. There is a risk of explosion!
Keep batteries away from children, do not short circuit batteries or disassemble.
Seek a doctor’s advice immediately if a battery is swallowed.
If necessary, clean the contacts on the battery and equipment before inserting the batteries.
Ensure that you insert the batteries the right way round.
Remove flat batteries immediately from the equipment. There is an increased risk of leakage.
Always change all batteries in one go.
Insert only batteries of the same type, do not use different types of batteries or used and new batteries together.
Make sure that the equipment is switched off after use.
Remove the batteries if the equipment is not used over a longer period.Keep this safety information in a safe place.

Layout and items supplied

Layout (Fig. 1-3)

On/Oﬀ switch (blocking the laser)
Horizontal laser
Vertical laser
LED display
Laser line selector button
Battery compartment cover
¼ inch female thread
Universal clamp
Adjusting screw
¼ inch male thread with wheel

Items suppliedPlease check that the article is complete as speciﬁ ed in the scope of delivery. If parts are missing, please contact our service center or the store where you made your purchase at the latest within 5 workdays after purchasing the article and upon presentation of a valid bill of purchase.

Open the packaging and take out the equipment with care.
Remove the packaging material and any packaging and/or transportation braces (if present).
Check to see if all the items are supplied.
Inspect the equipment and accessories for transport damage.
If possible, keep the packaging until the end of the guarantee period.

Danger!The equipment and packaging material are not toys. Do not let children play with plastic bags, plastic sheets and small parts. There is a risk of choking and suﬀ ocating!

Cross-line laser
Mounting
Bag
Original operating instructions
Safety information

Intended use

The cross-line laser uses lasers to project lines onto the wall and is therefore designed for aligning objects such as tiles, windows, doors, or pictures. The equipment is allowed to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user/operator and not the manufacturer will be liable for any damage or injuries of any kind resulting from such misuse. Please note that our equipment has not been designed for use in commercial, trade, or industrial applications. Our warranty will be voided if the equipment is used in commercial, trade, or industrial businesses or for equivalent purposes.

Technical data

Power supply: ………….. 2 x 1.5 V; type AA (LR06)Self-leveling range: ………………………………….± 4°Accuracy: …………. ± 3⁄16 -in. @ 30-ft (± 0.5 mm/m)Work range: ………………………………….. 26 ft (8 m)Wavelength of vertical laser: ………………. 635 nmWavelength of horizontal laser: ……………. 635 nmLaser class: ………………………………………………. IIOutput power: ………………………………….. < 1 mWWeight: …………………………………0.44 lbs (0.2 kg)

This standard applies to equipment designed to be safe at least under the following conditions:a) Indoor useb) Altitude up to ~6500ft (2000m)c) Temperatures 41°F – 104°F ( 5°C – 40°C)d) Maximum relative humidity 80% for temperatures up to 88°F (31°C) decreasing linearly to 50% relative humidity at 104°F (40°C)

Before starting the equipment

Inserting batteries (Fig. 2)

Turn off the equipment using the ON/OFF switch (1)
Open the battery compartment cover (6) by pressing the nib (a) down.
Insert the batteries (b), ensuring that you fit them the right way round.
Close the battery compartment cover (6) again, making sure that it locks securely
If the LED indicator flashes red continuously even though the device is upright, this means that the batteries are flat. Replace them as described above.

Using the universal clamp (Fig. 3/Item 8)You can fasten the supplied universal clamp (8) to a table, shelf or similar object by clamping it in position. To ﬁt the equipment to the universal clamp, proceed as follows:

Place the equipment by the female thread (7)on the base of the equipment onto the male thread (10) of the universal clamp (8)
Screw the equipment to the mounting with the help of the wheel
Using the adjusting screw (9) and the ball joints (a), you can tilt the equipment to the angle you requireTo disassemble, proceed in reverse order

Operation

Switching On/Oﬀ (Fig. 1)Switching on:

Place the laser on a flat surface or fit it to the universal clamp and fasten it as described in 5.2.
To switch the laser on, push the On/Off switch to the left (viewed from the front). The lasers switch on, the green LED (4) comes on and the pendulum will no longer be blocked, which means the laser can be aligned.
Press the button (5) to display or hide the vertical or horizontal lines again individually.

Switching oﬀ: To switch oﬀ, push the On/Oﬀ switch back to the position on the right (viewed from the front). The lasers which oﬀ and the pendulum will be blocked.

Important! To prevent damage during transport or storage, the equipment must always be switched oﬀ as described above.

Automatic alignment of the laser (Fig. 4)After the laser has been switched on with the On/Oﬀ switch (1), the lasers are aligned automatically by the pendulum so that the vertical and horizontal lines are displayed level on the wall. (See Fig. 4)Press the button (5) to display or hide the vertical or horizontal line individually.

Important!Make sure that the equipment is never tilted more than 4 degrees or stands at an angle. If this is the case, the laser beams will ﬂ ash and the LED (4) will light up red. Manual alignment of the laser (Fig. 5)The laser can also be aligned manually, to enable a diagonal line to be displayed. Proceed as follows:

Place the laser on a flat surface or fit it to the universal clamp and fasten it as described in 5.2.
To switch the equipment on, push the On/Off switch (1) to the left (viewed from the front).
Wait until the lasers are aligned and then move the On/Off switch (1) back to the right.
Now press the button (5). The lasers switch on and the LED (4) lights up red, because the pendulum is blocked.
Now you can tilt the laser to the angle you require so that the lines are displayed diagonally on the wall. (See Fig. 5)
Press the button (5) to hide or display the vertical or horizontal line individually or to switch the equipment off again.

Cleaning, maintenance, and ordering spare parts

Cleaning

Keep all safety devices, air vents, and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it down with compressed air at low pressure.
We recommend cleaning the equipment immediately each time after use.
Clean the equipment regularly with a damp cloth and some soft soap. Do not use cleaning agents or solvents; these may be aggressive to the plastic parts in the equipment. Ensure that no water can get intothe interior of the equipment. The ingress of water into an electric power tool increases the risk of an electric shock.

MaintenanceThere are no other parts inside the equipment which require maintenance.

Ordering replacement parts:Service

If your power tool requires service, contact an authorized Einhell USA dealer or call the Einhell USA customer service center at 1-866-EINHELL (1-866-346-4355). Only identical replacement parts should be utilized for repairs. This will ensure that the safety of the power tool is maintained.
If the battery charger cable is damaged, it must be immediately replaced to avoid a hazard. Contact the Einhell USA ® customer the service center at 1-866-EINHELL(1-866-346-4355) for assistance.

Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council oﬃ ces.

Battery Caution + DisposalDisposalShould your appliance need replacement after extended use, do not dispose of it with the household refuse, but in an environmentally safe way. Waste produced by electrical machine items should not be handled like normal household rubbish. Please recycle where recycling facilities exist. Check with your local authority or retailer for recycling advice. Always dispose of your battery pack according to federal, state, and local regulations. Contact a recycling agency in your area for recycling locations.

CAUTION! Even discharged battery packs contain some energy. Before disposing of, use electrical tape to cover the terminals to prevent the battery pack from shorting, which could cause a ﬁ re or explosion.WARNING! To reduce the risk of injury or explosion, never burn or incinerate a battery pack even if it is damaged, dead, or completely discharged. When burned, toxic fumes and materials are emitted into the surrounding atmosphere.

1. Batteries vary according to the device. Consult your manual for speciﬁ c information.2. Install only new batteries of the same type in your product (where applicable).3. Failure to insert batteries in the correct polarity, as indicated in the battery compartment or manual may shorten the life of the batteries or cause batteries to leak.4. Do not mix old and new batteries.5. Do not mix Alkaline, Standard (Carbon-Zinc), or Rechargeable (Nickel Cadmium, Nickel Metal Hydride, or Lithium-Ion) batteries.6. Do not dispose of batteries in ﬁ re.7. Batteries should be recycled or disposed of as per state and local guidelines.

When shipping or disposing of batteries and cordless tools, always ensure that they are packed individually in plastic bags to prevent short circuits and ﬁ res.

Storage

Store the equipment and its accessories out of children‘s reach in a dark and dry place at above freezing temperature. The ideal storage temperature is between 41°F and 86°F (5°C and 30°C). Keep the electric tool in ts original packaging. The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying the products, is strictly subject to the express consent of iSC GmbH. Subject to technical changesEinhellUSA.com

EINHELL CUSTOMER PROMISE

QUALITY COMES FIRST. The Einhell name is synonymous with high-performance tools and high-qualityEuropean craftsmanship. From cordless screwdrivers to electric lawn mowers, Einhell USA designs and develops state-of-the-art handheld power and garden tools for DIY enthusiasts, hobby gardeners, and handymen.Einhell USA’s quality assurance and engineering teams ensure products are subjected to stringent quality andperformance tests. We know that sometimes tough tools go through tough times. In the event that you shouldexperience any issue with your product, you have our commitment that we’ll do everything we can to get youback a tool that’s ready to work as hard as you do.

PRODUCT REGISTRATION:Einhell strongly encourages you to register your purchase. You can register online at EinhellUSA.com Failure to register your product purchase will not diminish your warranty rights. However, registering your purchase will allow Einhell to better serve you with any of your customer services needs.WHAT IS COVERED?Einhell warrants to the owner that if this Machine fails within 2 years from the date of purchase due to a defect in material or workmanship or as a result of normal wear and tear from ordinary household use, Einhell will send a replacement part or product, as needed, free of charge and with free shipping to the original purchaser. If, in Einhell’s sole discretion, the failed Machine cannot be repaired with a part, Einhell will elect to either (A) send a new Machine at no charge and with free shipping or (B) refund the full purchase price to the owner.

WHO CAN SEEK WARRANTY COVERAGE?This Warranty is extended by Einhell to the owner of this Machine (a “Machine” consists of a product powered by a motor) for residential and personal household use only. This warranty is limited to thirty (30) days from the start of the original purchase of any EINHELL brand product that is used for commercial purposes, or any other income-producing purpose. Should ownership of this machine change during the coverage period, please update the Machine’s owner information at EinhellUSA.com

WHAT IS NOT COVERED?This warranty does not cover any product that has been subject to misuse, neglect, negligence, or accident or that has been operated in any way contrary to the operating instructions as speciﬁ ed in the operator’s manual. This Warranty does not cover cosmetic changes that do not aﬀ ect performance.

This Warranty is only valid if the Machine is used and maintained in accordance with the instructions, warnings and safeguards contained in the owner’s manual. Einhell will not be responsible for the cost of any unauthorized warranty repairs. This warranty does not cover any cost or expense incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non-use of this product while waiting for a replacement part or unit under this warranty. Wearing parts like belts, augers, chains and tines are not covered under this warranty, and can be purchased at EinhellUSA.com or by calling 1-866-EINHELL (1-866-346-4355). Batteries are covered in full for 90-days from the date of purchase.

Repair, replacement or refund of the purchase price are the exclusive remedies of the purchaser and the soleliability of Einhell under this warranty. No employee or representative of Einhell is authorized to make any additional warranty or any modiﬁ cation to this warranty which may be binding upon Einhell. Accordingly, the purchaser should not rely upon any additional statements made by any employee or representative of Einhell. In no event, whether based on contract, indemnity, warranty, tort (including negligence), strict liability or otherwise, shall Einhell be liable for any special, indirect, incidental, or consequential damages, including, without limitation, loss of proﬁ t or revenue.Some states do not allow limits on warranties. In such states, the above limitations may not apply to you. Outside the USA and Canada, other warranties may apply.

Note:

www.EinhellUSA.com

References

[xyz-ips snippet=”download-snippet”]

Posted

2023-01-18

Einhell

admin

Tags:

Einhell, Self-Leveling Cross-Line Laser, TC-LL 2