Einhell TE-CD 18 Li-i BL-Solo Cordless Hammer Drill/Screwdriver Instruction Manual

Einhell TE-CD 18 Li-i BL-Solo Cordless Hammer Drill/Screwdriver Instruction Manual

Danger! – Read the operating instructions to reduce the risk of inquiry

Caution! Wear ear-muff s. The impact of noise can cause damage to hearing.

Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working onwood and other materials. Never use the device to work on any materials containing asbestos!

Caution! Wear safety goggles. Sparks generated during working or splinters, chips and dust emittedby the device can cause loss of sight.

Change the gear only when the drill is at a standstill. If you fail to observe this point, the gearing may be damaged.

Store the battery only in dry rooms with an ambient temperature of +10°C to +40°C. Place only charged batteries in storage (charged at least 40%).

Safety class IIFor use in dry rooms only.

Danger!

When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care.Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be found in the enclosed booklet.

Warning!

Read all the safety information, instructions, illustrations and technical data provided on or with this power tool. Failure to adhere to the following instructions may result in electric shock, fi re and/or serious injury.Keep all the safety information and instructions in a safe place for future use.

2. Layout and items supplied

2.1 Layout (Fig. 1)
  1.  Torque selector
  2. Battery capacity indicator
  3. Changeover switch
  4. ON/OFF switch
  5. Battery pack
  6. Battery charger
  7.  Selector switch for 1st/2nd gear
  8. Pushlock button
  9. Quick-change drill chuck
  10. LED lamp
  11. Additional handle
  12.  Selector switch for driving/drilling/impact drilling

2.2 Items suppliedPlease check that the article is complete as specifi ed in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

  • Open the packaging and take out the equipment with care.
  • Remove the packaging material and any packaging and/or transportation braces (if available).
  • Check to see if all items are supplied.
  • Inspect the equipment and accessories for transport damage.
  • If possible, please keep the packaging until the end of the guarantee period.

Important!

The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suff ocating!

  • Cordless drill/screwdriver
  • Additional handle
  • Battery charger (not included in delivery with 45.138.60)
  • Battery (not included in delivery with 45.138.60)
  • Original operating instructions
  • Safety instructions

3. Proper use

The cordless impact drill/driver is designed for tightening and undoing screws, for drilling in wood, metal and plastic, and for impact drilling in stone, in each case when using the appropriate bits.The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the. machine is used in commercial, trade or industrialbusinesses or for equivalent purposes.

4. Technical data

Voltage supply .                                      18 V d.c.Idling speed: .                                      .  0-500/0-1800 rpmTorque settings: .                                    20+1+1Forward and reverse rotation . ..            yesChuck clamping width                         . max. 13 mmBattery charger output voltage: .           21 V d. c.Battery charger output current: .         . .3 AMains voltage for charger: .                  .200-250 V~ 50-60 HzBattery type:                                         Lithium-ionNumber of battery cells:                       5/10Battery capacitance:                              1.5 Ah / 5.2 AhWeight..                                                1.69 kg / 2.2 kgMax. screw diameter:                            6 mm

The maximum screw diameter indicates the maximum diameter of the screw that can be screwed into wood. The screw diameter can vary depending on the type of wood.

Danger!

Sound and vibration Sound and vibration values were measured in accordance with EN 62841.LpA sound pressure level                             79.88 dB(A)KpA uncertainty                                           3 dBLWA sound power level                               90.88 dB(A)KWA uncertainty                                        3 dBWear ear-muff s.The impact of noise can cause damage to hearing.Total vibration values (vector sum of three directions) determined in accordance with EN 62841.Drilling in metal Vibration emission value ah ≤ 2.5 m/s2 K uncertainty = 1.5 m/s2

Impact drilling in concrete

Vibration emission value ah,ID = 10.62 m/s2Uncertainty K = 1.5 m/s2The stated vibration emission levels and stated noise emission values were measured in accordance with a set of standardized criteria and can be used to compare one power tool with another.The stated vibration emission levels and stated noise emission values can also be used to make an initial assessment of exposure.

Warning:

The vibration and noise emission levels may vary from the level specifi ed during actual use, depending on the way in which the power tool is used, especially the type of workpiece it is used for.Keep the noise emissions and vibrations to a minimum.

  • Only use appliances which are in perfect working order.
  • Service and clean the appliance regularly.
  • Adapt your working style to suit the appliance.
  • Do not overload the appliance.
  • Have the appliance serviced whenever necessary.
  • Switch the appliance off when it is not in use.
  • Wear protective gloves.

Caution!

Residual risksEven if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in connection with the equipment’s construction and layout:

  1. Lung damage if no suitable protective dust mask is used.
  2. Damage to hearing if no suitable ear protection is used.
  3. Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.

Limit the operating time.

All stages of the operating cycle must be considered (for example, times in which the electric tools are switched off and times in which the tool is switched on but operates without load).

5. Before starting the equipment

Be sure to read the following information before you use your cordless screwdriver for the fi rst time:

  1. Charge the battery pack with the charger supplied. An empty battery pack requires a charging period of approximately 0.5-1 hour.
  2. Only ever use sharp drill bits and screwdriver bits which are suitable for the purpose and in faultless condition.
  3.  Always check for concealed electric cables and gas and water pipes when drilling and screwing in walls.

6. Operation

6.1 Charging the LI battery pack (Fig. 2-3)

  1. Remove the battery pack (5) from the handle, pressing the pushlock buttons (8) downwards to do so.
  2. Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (6) into the mains socket outlet. The green LED will then begin to fl ash.
  3. Push the battery pack onto the battery charger.

In section 10 “Charger indicator” you will fi nd a table with an explanation of the LED indicator on the charger.

If the battery pack fails to become charged, please check

  • whether there is voltage at the socket-outlet
  • whether there is proper contact at the charging contacts on the charger. If the battery still fails to become charged, please return
  • the charger
  • the battery pack to our Customer Service Department.To ensure that the LI battery pack provides long service you should take care to recharge it promptly. You must recharge the battery pack when you notice that the power of the cordless screwdriver drops.

6.2 Torque setting (Fig. 4 / Item 1)

Important! The tool must be at a standstill when you set the torque with the setting ring.The cordless screwdriver is fi tted with a mechanical torque selector.The torque for a specifi c size of screw is selected with the set-collar (1). The correct torque depends on several factors:

  • on the type and hardness of material in question
  • on the type and length screws used
  • on the requirements needing to be met by the screwed joint.The clutch disengages with a grating sound to indicate when the set torque is reached.

6.3 Selector switch for driving/drilling/impact drilling (Fig. 4/Item 12)

  • For driving purposes, set the selector switch (12) to the „Screw“ position. The torque is adjusted via the torque setting (1) (see point6.2). • For drilling purposes, set the selector switch(12) to the „Bit“ position. The slip coupling is now off and the maximum torque is available regardless of the torque setting (1). •For impact drilling purposes, set the selector switch (12) to the „Hammer“ position. The slip coupling is now off and the maximum torque is available regardless of the torque setting (1).

Important! Change the torque setting (1) and the selector switch for driving/drilling/impact drilling (12) only when the equipment is at a standstill.

6.4 Forward/Reverse switch (Fig. 5 / Item 3)

With the slide switch abo.

ve the On/Off switch you can select the direction of rotation of the batterypowered drill/screwdriver and secure it against being switched on accidentally. You can choose between clockwise and anticlockwise rotation. To avoid causing damage to the gearing it is advisable to change the direction of rotation only when the tool is at a standstill. The On/Off switch is blocked when the slide switch is in centre position.

6.5 On/Off switch (Fig. 5 / Item 4)

Infi nitely variable speed control is possible with the On/Off switch. The further you press the switch, the higher the speed of the battery-powered drill/screwdriver.

6.6 Changing over from 1st gear to 2nd gear (Fig. 4 / Item 7)

You can work at a higher or lower speed depending on the position of the selector switch. To avoid damaging the gear unit you should only change over gears when the tool has stopped.

6.7 Battery capacity indicator (Fig. 6 – Item 2)

Press the battery capacity indicator switch (a). The battery capacity indicator (2) shows the charge status of the battery using 3 LEDs.

6.7 Battery capacity indicator (Fig. 6 – Item 2)

Press the battery capacity indicator switch (a). The battery capacity indicator (2) shows the charge status of the battery using 3 LEDs.

6.10 Screwdriving

We recommend using self-centering screws (e.g. Torx screws, recessed head screws) designed for reliable working. Be sure to use a bit that matchesthe screw in shape and size. Set the torque, as described elsewhere in these operating instructions, to suit the size of screw.

6.11 Mounting the additional handle (Fig. 8 / Item 11)

The additional handle (11) enables you to achieve better stability while using the equipment. Do not use the equipment without the additional handle.The additional handle (11) can be screw-fi tted in two positions (A, B). It is suitable therefore for right-handed and left-handed users.

7. Cleaning, maintenance and ordering of spare parts Danger!

Always pull out the mains power plug before starting any cleaning work.

7.1 Cleaning • Keep all safety devices, air vents and the motor housing free of dirt and dust as far aspossible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.

  • We recommend that you clean the device immediately each time you have finished using it.
  • Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. Theingress of water into an electric tool increases the risk of an electric shock.

7.2 Maintenance

There are no parts inside the equipment which require additional maintenance.

7.3 Ordering spare parts and accessories

Please provide the following information when ordering spare parts:Type of unit  Article number of the unitID number of the unitSpare part number of the required spare partFor our latest prices and information please go to www.isc-gmbh.infoTip! For good results we recommend high-quality accessories from ! www.kwb.eu

8. Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offi ces.

9. Storage

Store the equipment and accessories out of children’s reach in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electrictool in its original packaging.

10. Charger indicator

Indicator status Explanations and actions
Red LED Green LED
Off Flashing Ready for use

The charger is connected to the mains and is ready for use; there is no battery pack in the charger
On Off Charging

The charger is charging the battery pack in quick charge mode. The char- ging times are shown directly on the charger.

Important! The actual charging times may vary slightly from the stated

charging times depending on the existing battery charge.
Off On The battery is charged and ready for use.

The unit then changes over to gentle charging mode until the battery is fully charged.

To do this, leave the rechargeable battery on the charger for approx. 15 minutes longer.

Action:

Take the battery pack out of the charger. Disconnect the charger from the mains supply.
Flashing Off Adapted charging

The charger is in gentle charging mode.

For safety reasons the charging is performed less quickly and takes more time. The reasons can be:

– The rechargeable battery has not been used for a very long time.

– The battery temperature is outside the ideal range.

Action:

Wait for the charging to be completed; you can still continue to charge the battery pack.
Flashing Flashing Fault

Charging is no longer possible. The battery pack is defective.

Action:

Never charge a defective battery pack. Take the battery pack out of the charger.
On On Temperature fault

The battery pack is too hot (e.g. due to direct sunshine) or too cold (below 0° C).

Action:

Remove the battery pack and keep it at room temperature (approx. 20° C) for one day .

For EU countries onlyNever place any electric power tools in your household refuse.To comply with European Directive 2012/19/EU concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste anddisposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.Recycling alternative to the return request:As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment.The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any accessoriesor aids without electrical components supplied with the old equipment.The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the iSC GmbH. Subject to technical changes.

This consignment contains lithium-ion batteries.  In accordance with special provision 188 this consignment is not subject to the ADR regulations. Handle with care. Danger of ignition in case of damage to the consignment package. If the consignment package is damaged: Check and if necessary repackage.For further information contact: 0049 9951 95920-66. Outside Germany charges will apply instead for a regular call to a landline number in Germany.

Service information

We have competent service partners in all countries named on the guarantee certifi cate whose contact details can also be found on the guarantee certifi cate. These partners will help you with all service requestssuch as repairs, spare and wearing part orders or the purchase of consumables. Please note that the following parts of this product are subject to normal or natural wear and that thefollowing parts are therefore also required for use as consumables.

Category Example
Wear parts* Drill chuck, Battery
Consumables* Bit inserts/drill bits
Missing parts

* Not necessarily included in the scope of delivery!In the eff ect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Pleaseensure that you provide a precise description of the problem and answer the following questions in all cases:

  • Did the equipment work at all or was it defective from the beginning? •
  • Did you notice anything (symptom or defect) prior to the failure?
  • What malfunction does the equipment have in your opinion (main symptom)?Describe this malfunction

Warranty certifi cate

report this ad

Dear Customer,All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the addressshown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

  1. These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not aff ected by this guarantee. Our guarantee is free of charge to you.
  2. The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectifi cation of said defects on the product or the replacement of the product, whichever we prefer. Please note that our devices are not designed for use in commercial, trade or professional applications.A guarantee contract will not be created if the device has been used by commercial, trade orindustrial business or has been exposed to similar stresses during the guarantee period.
  3.  The following are not covered by our guarantee:– Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrectmains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance.– Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand,stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it).– Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.
  4.  The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period.The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fi tted will not result in an extensionof the guarantee period, and no new guarantee will become active for the work performed or parts
  5. tted. This also applies if an on-site service is used.
  6.  To make a claim under the guarantee, please register the defective device at: www.isc-gmbh.info. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identifi cation will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement. Of course, we are also happy off er a chargeable repair service for any defects which are not covered bythe scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as set out in the service information in these operating instructions.

 

 

Read More About This Manual & Download PDF:

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , , ,