USER MANUAL
27” LED MONITOReiQ-27CVQHD165IFSGHLDThank you for choosing electriQPlease read the user manual before using this monitor and keep it safe for future referenceVisit www.electriQ.co.uk to view our entire range of Intelligent Electricals
SAFETY INFORMATION
- Read these instructions – All the safety and operating instructions should be read before this product is operated.
- Keep these instructions – The safety and operating instructions should be retained for future reference.
- Heed all warnings – All warnings on the appliance and in the operating instructions should be adhered to.
- Follow all instructions – All operating and usage instructions should be followed.
- Do not use this equipment near water, or in humid environments – The appliance should not be used near water or moisture e.g. in a wet basement or near a swimming pool.
- Clean only with a dry cloth. Do not use solvents or petroleum-based fluids.
- Do not block any ventilation openings.
- Do not install near any heat sources such as radiators, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not tamper with the supplied plug. This plug is a BS1363 standard plug.
- Protect the power cord from being walked on or trapped, particularly at the plug and at the point where it exits from the appliance.
- Only use attachments/accessories specified by the manufacturer.
- Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart or stand is used, use caution when moving it to avoid any injuries or damage from it tipping over.
- Unplug the apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as if the power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus or it has been exposed to rain or moisture, it does not operate normally or has been dropped.
- Please keep the unit in a well-ventilated environment.
- The monitor should only be connected to the main power supply as rated on the back of the equipment.
- To prevent overload, do not share the same power supply socket with too many other electronic components.
- Do not place any connecting wires where they may be stepped on or tripped over.
- Do not place heavy items on the cable as this may cause damage.
- When removed from a socket hold by the plug and not the wires.
- Disconnect the power immediately and seek professional help if the plug or cable is damaged, liquid has spilled onto the unit, if accidentally exposed to water or moisture, if anything accidentally penetrates the ventilation slots or if the unit does not work normally.
- Do not remove the safety covers. There are no user-serviceable parts inside. Trying to service the unit yourself is dangerous and may invalidate the product’s warranty. Only qualified personnel should service this apparatus.
- Do not block ventilation slots on the back cover. The monitor can be placed in a cabinet but ensure at least 5cm (2″) clearance all around. Do not tap or shake the screen, this may damage internal components.
- WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and objects filled with liquids, such as vases, shall not be placed on the apparatus.
- WARNING: The wall plug socket is used as a disconnection device and should remain readily accessible.
- WARNING: The batteries shall not be exposed to excessive heat such asdirect sunlight or fire.
- Although every effort is made to maintain the accuracy of the manual, due to continuous product development, some variation from the manual is possible.
- The availability of features and settings may vary depending on the input source and method of connection.
- Although every effort is made to maintain the accuracy of the manual, due to continuous product development, some variation from the manual is possible.
- The availability of features and settings may vary depending on the input source and method of connection.
- The available resolutions and refresh rates may be limited by the capabilities and/or settings of the source device.
| AT FULL VOLUME, PROLONGED LISTENING MAYDAMAGE THE USER’S HEARING. | ||
| This warning sign is to warn of dangerous voltage inside the product. | CAUTION: To reduce the risk of electric shock, DO NOT remove the cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. |
WHAT’S INCLUDED
STAND INSTALLATION
- Open the packing box, take out the bracket and the base, and use one bolt (the bolt can be found at the base) to reach the base of the stand to the upright section, as shown below:
- An ach the stand onto the rear of the monitor by local ng the top of the upright sec on into position on the rear of the monitor before clipping in the boom of the mounting plate. Ensure the mounting plate is fully located.
- Use one Bolts (B) to secure the mounting plate to the rear of the monitor.
- Use both hands to stand the assembled monitor on a flat desktop.
NOTES:
- Due to the heavyweight and dimensions of the LCD screens and their fragile nature, we recommend that they be unpacked and assembled by 2 people.
- electriQ and its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use, or failure to observe these safety instructions. In such cases, any guarantee will expire.
- The stand can be removed from the rear of the monitor by pressing the quick-release button on the rear of the monitor.
WALL-MOUNT INSTALLATION
- As shown in the figure above, use a screwdriver to remove the four screws locked in the middle of the whole machine (when disassembling the screws, the display screen cannot leave the polyol foam to prevent the screen from breaking)
- Take out the wall-mounted adapter/four CM4*23 screws from the accessories as shown in the figure above, assemble it in the middle of the whole machine, and fix it by locking.
- Do not pinch the screen directly with your hands during the process of changing the product to prevent the screen from breaking.
NOTES:
- Do not pinch the screen directly with your hand when hanging the product to prevent the screen from breaking.
- Due to the heavyweight and dimensions of LCD screens and their fragile nature, we recommend that they are unpacked and assembled by 2 people and professional installers are used to wall mount them (Wall mounting is optional).
- If you do not understand the instructions or are unsure how to install this product, please contact a professional for assembly advice and assistance.
- Careful consideration should be made regarding the location the monitor is to be wall-mounted as some walls are not suitable for installation. If the monitor is to be mounted on drywall, the mount must be anchored into a wooden stud, concrete block, or brick behind the drywall. Installing on drywall alone may not support the weight of the display.
- When drilling holes, it is particularly important to take care of electrical cables, water, or gas pipes in the wall. Please follow the instructions provided by the wall bracket manufacturer and ensure that all fixing screws supplied are used.
- electric and its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use, or failure to observe these safety instructions. In such cases, any guarantee will expire.
CONNECTIONS AVAILABLE ON THE MONITOR
POWER
- HDMI x 3 (HDMI 2.0, QHD 144Hz, FreeSync)
- DP IN (Display Port 1.4, QHD 165Hz, FreeSync)
- Type-C (QHD 60Hz)
- AUDIO OUT
- USB
WALL MOUNTING
- The monitor is provided with mounting holes for a VESA-approved wall mounting bracket (not supplied).
- The VESA mounting pattern is: 100x100mm and the size of the screws is 4 x M6 x 10 (not supplied)
- Do not use screws longer than specified or damage will occur to the internal components.NOTE: As the monitor is considered heavy, please consult with a professional wall mount installer to perform the installation.
GETTING STARTED
MONITOR CONTROLS
|
Select signal source or Exit the menu |
|
Go Up within the Main Menu or increase the value of the selected item |
|
Go Down within the Main Menu or decrease the value of the selected item |
 |
Enter the Main OSD Menu and Select submenu |
|
Turn the monitor On or Off |
The monitor includes one-touch options to access common songs.
INITIAL SET UP
Connect the monitor to a power socket.
- Press the POWER button on the monitor or turn it on (The indicator will be blue)
- Connect the relevant cable to the corresponding input on the monitor. The source will be automatically detected.
- To change between inputs, press the E btton to enter the source menu. Use the and burns to choose the input source between DP1, HDMI1, HDMI2, and DP2.
MENU OPTIONS
The menu for the monitor can be accessed by pressing the menu button on the control panel. This menu is separated into the following sub-menus: Input source, Brightness/Contrast, Colour Songs, Picture Quality Songs, Display, Audio, OSD (On-screen display), and others. Details of each menu can be found in the following section.
OSD MENULED EFFECTS SYSTEM CONSOLE
PICTURE Mode
Picture modeSwitch the scene mode shortcut button you can change the picture mode directly: Standard, Photo, Movie, Game, FPS, and RTS.
COLLIMATION Mode
Used to choose the Crosshairs that can be displayed in the center of the screen.
INPUT SOURCE
| BrightnessBlack levelContrast DCRLight Sensor | Adjust the brightness of the display between 0 and 100.Adjust the black level of the display between 0 and 100.Adjust the contrast of the display between 0 and 100.Turn the Dynamic Contrast Rao Feature On or Off.Turn the Light Sensor Feature On or Off. |
COLOUR SETTINGS
| GammaPicture ModeColourTemperatureLow Blue LightHueSaturationRGB Range | Change the Gamma value for the display between 1.8, 2.0, 2.2, 2.4, 2.6Change the picture mode between Standard, Photo, Movie, Game, FPS, and RTS.Change the Colour Temperature of the display to Normal, Warm, Cool, or User.When the User Mode is selected, the Red, Green, and Blue values can be adjusted independently between 0 and 100.Change the blue light emitted by the display between0 and 100.Change the Hue value between 0 and 100.Change the Saturation of the display between 0 and 100.Change the RGB Range the display full and Limit. |
PICTURE QUALITY SETTINGS
| SharpnessResponse TimeNoise Reduction DynamicLuminanceControlMPRT | Change the display Sharpness between 0 and 100.Turn the Response OverDrive feature between Off, High, Middle of lowAdjust the level of Noise Reduction between Low, Medium, High, or Off.Turn the Dynamic Luminance Control feature On or Off.Turn the moon blur on or off. |
DISPLAY
Aspect RatioChange the image aspect ratio to Wide-Screen. 4:3, Auto, 1:1,
AUDIO
| Mute | Turn On and off to mute and unmute the audio out |
| Volume | Adjust the output volume between 0 and 100. |
| Audio Source | Chose which source the audio is output from Type-C, DP, HDMI1, HDMI2, HDMI3, AutoSource |
MULTI-WINDOW
OSD
| Language | Change the OSD Menu display language between English, Chinese, Korean, Russian, Spanish, Japanese and French. |
| OSD H Position | Change the horizontal position of the OSD Menu between 0 and 100. |
| OSD V Position | Change the vertical position of the OSD Menu between 0 and 100. |
| OSD Transparency | Change the transparency value of the OSD Menu between 0 and 100. |
| OSD Time Out | Change how long the OSD Menu is on before it automatically exits. |
| OSD Rotation | Change the OSD Rotation Normal,90,180,270 |
OTHER
| DP Version | Change the DP version |
| FreeSync (Adaptive Sync) | Turn Free Sync On or Off. |
| HDR | Turn the HDR on or off. |
| Trun on Type-C Function | Turn the Type-C Function on or off. |
| USB Update FW | Use for update software |
| Reset | Restore factory default setting. |
SPECIFICATION
|
Product Model |
eiQ-27CVQHD165IFSGHLD |
|
| Screen Size | 27” Diagonal | |
| Panel Type | VA Panel | |
| Aspect Ratio | 16:9 | |
| Power Supply | DC 180W 19.5V 9.23A | |
| Power Consumption | 80W Typ, 175W Max | |
| Dimensions | 615.8 * 122.39 * 371.9 mm | |
| Net / Gross Weight | 5.18 kg / 8.4 kg | |
| Picture | Maximum Resolution | 2560 * 1440 |
| Brightness | 1000 cd/m2 (HDR) / 650 cd/m2 | |
| Static Contrast | 3000:1 | |
| Response Time | 1ms | |
| Viewing Angle (H/V) | 178° / 178° | |
| Terminals | USB Input | USB- type C x 1 |
| HDMI Input | HDMI 2.0 x 3 | |
| Display Port Input | DP 1.4 x 1 | |
| Audio Output | x 1 | |
| Working Temperature | 0°C – 40°C | |
| Working Humidity | 10% – 85% Non-condensing | |
| Speaker Specifications | 4R2W x 2 |
TROUBLESHOOTING
|
PROBLEM |
SOLUTION |
| No power | Insert the plug securely into the power outlet. |
| No picture | Ensure that the equipment is connected properly. |
| Ensure the correct input is selected. | |
| Buttons on the monitor don’t do anything | Disconnect the power plug and then reconnect it. (The unit may not be operating properly due to lightning, static, or other factors.) |
| Noise or other interference | Electronic equipment near the unit may be causing interference. Relocate the unit or move the equipment. |
ENVIRONMENTAL PROTECTION
Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participate in civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when deposing your equipment. Please contact the local council for details of your local household waste recycling centers.
report this adelectriQ UK SUPPORTwww.electriQ.co.uk/supportCall: 0330 390 3061Office hours: 9 AM – 5 PM Monday to Fridaywww.electriQ.co.ukUnit J6, Lowfields Business ParkLowfields Way, EllandWest Yorkshire, HX5 9DA
References
[xyz-ips snippet=”download-snippet”]