Touch Screen Wine & Beverage Cooler EL-BWC102-02
o ur W in e & B e v e r a g e C o o le rThis unit can be used for storage and/or service. The unit has seamless glass doors and soft interior lights to elegantly display your wine and other beverages.S e r v in g W in eStoring wines at the proper temperature is important. To preserve them as long as possible, wine should be stored at approximately 55° Fahrenheit. However, the chart below suggests the optimal drinking temperature for the different styles of wine.
°C
°F
Wine Style
18
64
Full Bodied Red Wines, Shiraz
17
62
Tawny Port
15
59
Medium Bodied Red Wines
14
57
Amontillado Sherry
13
55
Light Bodied Red Wines
12
54
Full Bodied White Wines
11
52
Medium Bodied White Wines
10
50
Rosé, Light Bodied White Wines
9
48
Vintage Sparkling
8
46
Fino Sherry
7
45
Non Vintage Sparkling
732 South Racetrack Road, Henderson, Nevada 89015
3
Table of ContentsIMPORTANT SAFETY INSTRUCTIONS ……………………………………………6 ELECTRICAL CONNECTION………………………………………………………..7 PARTS AND SPECIFICATIONS…………………………………………………….8 INSTALLATION ………………………………………………………………………9 OPERATING YOUR WINE & BEVERAGE COOLER ……………………………. 10 CARE AND MAINTENANCE………………………………………………………. 12 PROBLEMS WITH YOUR APPLIANCE ………………………………………….. 13 TROUBLESHOOTING …………………………………………………………….. 13 TERMS OF SALE AND WARRANTY …………………………………………….. 14 SERVICE & IMPORTANT NOTICE ………………………………………………. 22
732 South Racetrack Road, Henderson, Nevada 89015
5
ELECTRICAL CONNECTIONImproper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, frayed or shows cracks or abrasions across its length, have it replaced at an authorized service center.For your protection, this unit is equipped with a 3-conductor cord set that has a molded 3-prong grounding-type plug, and should be used in combination with a properly connected grounding-type outlet.Do not under any circumstances cut or remove the third ground prong from the power cord supplied. For personal safety, this appliance must be properly grounded. The cord should be secured behind the unit and not left exposed or dangling to prevent accidental injury. A standard electrical supply (115V AC – 60Hz), properly grounded in accordance with the National Electrical Code and local codes and ordinances, is required. When a standard 2-pin wall outlet is encountered, it is your responsibility to have it replaced with a properly grounded 3-pin wall outlet. Never unplug the unit by pulling the power cord. To disconnect the appliance, always grip the plug firmly and pull straight out from the wall outlet. When moving the unit, be careful not to damage the power cord. The unit should always be plugged into its own individual electrical outlet with a voltage rating that matches the rating label on the unit. Do not pinch or kink the power supply cord. Repair or replace all power cords that have become frayed or damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the appliance, be careful not to damage the power cord.Extension CordCAUTION: It is strongly recommended that you do not use an adapter or an extension cord with this unit.
732 South Racetrack Road, Henderson, Nevada 89015
7
INSTALLATIONBEFORE USING YOUR APPLIANCERemove all packing material before using your appliance. IMPORTANT: Before connecting the unit to a power source, let it stand upright for approximately 24 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. Clean the interior surface with lukewarm water and a soft cloth.INSTALLATION OF YOUR APPLIANCEThis unit is designed for freestanding and built-in installation and indoor use only. Position the unit in a dry and well-ventilated place. Avoid placing the cooler near any source of heat or moisture, or in direct sunlight. Do NOT install the unit in a location with an ambient temperature that will fall below 41°F. For built-in installation, it is also important to keep space on each side and at the top of the appliance. If you plan to install the unit into cabinetry, please leave ¼” space on each side and at the top of the cooler as well as 1-2″ at the back of the cooler to ensure proper air circulation to cool the compressor and condenser. Also, be sure to not obstruct the front exhaust vent with any objects as this may affect the unit from performing properly. Place the appliance on a level surface strong enough to support it when it is fully loaded. It is important for the appliance to be leveled in order to work properly. You may need to make several adjustments to level it. To level the cooler, adjust the front leveling legs at the bottom of the cooler. For best performance it is recommended that you install the appliance in a location with an ambient temperature between 41°-100°F. If the ambient temperature is above or below recommended temperatures, the performance of the unit may be affected. It is recommended that you do not install the appliance near an oven, radiator or other heating source. Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Don’t install in a location where the temperature will fall below 41° F. For best performance, do not install the appliance behind a cabinet door or block the base grille. Do not store or install the appliance outdoors, in a garage, basement, or in moist areas. Plug the unit into an exclusive, properly installed-grounded wall outlet.INSTALLATION OF THE METAL HANDLESOn the door interior, slightly pull back the door gasket on the side you wish to install the handle to reveal the two (2) designated holes for handle installation. NOTE: Door gasket must not be removed, detached or altered as it may directly affect cooling performance.Using a screwdriver (not included), install the handle tightly as shown in the diagram above with the included screws, lock washers and flat washers (2 each).INSTALLING THE CHARCOAL FILTERTo install the charcoal filter, please follow the below instructions:· Place the carbon filter on top of the shelf.· The back of the filter has a 3M glue tape which you can affix to the shelf or the inside of the unit.
732 South Racetrack Road, Henderson, Nevada 89015
9
3Defrosting The unit defrosts automatically. The evaporator behind the rear wall of the unit defrosts automatically. The condensate collects in the drainage channel behind the rear wall of the unit, and flows through the drainage hole into the drip tray by the compressor where it evaporates. When the wine and beverage cooler run for some time, the wine and beverage cooler will enter to defrosting, the compressor stop running and the fan will keep running. The temperature will up to about 5°C when defrosting, then keep on running normally; It takes more time for the temperature to come up to 10°C when the setting temperature is low (for example the setting temperature is 4°C), and there are full of wines and beverages in the cabinet, and this is not a breakdown.The switch of interior light is under the control panel to control the light on or off.STORING WINE AND BEVERAGESWhile bottles may vary in size and dimension, approximately 24 traditional Bordeaux 750ml bottles and 58 12 oz. cans can be stored in your wine & beverage cooler. Please note that bottle capacities are approximate maximums when storing traditional Bordeaux 750 ML bottles and include bulk storage.SHELVESTo prevent damaging the door gasket, make sure the door is fully open when pulling shelves out of the rail compartment.For easy access to the bottles stored, pull the shelves out approximately 90%. Only pull out one shelf at a time. Never attempt to pull more than one.DOOR LOCKYour unit is provided with a lock and key combination. The keys are located inside the plastic bag that contains the Owner’s Manual. Insert the key into the lock and turn it counterclockwise to unlock the door. To lock the door, insert the key into the lock and turn it clockwise making sure metal pin is engaged completely. Remove the key and place it in a secure place for safekeeping.
732 South Racetrack Road, Henderson, Nevada 89015
11
ENERGY SAVING TIPSThe unit should be located in the coolest area of the room away from heat sources or direct sunlight. Ensure that the unit has proper allowances on all sides for proper ventilation. Never cover any air vents. Only open the cooler door for as long as necessary. Frequent opening of the door will affect internal temperature.
PROBLEMS WITH YOUR APPLIANCEYou can solve many common cooler problems easily, saving you the cost of a possible service call. Try the following suggestions to see if you can solve the problem before contacting Vinotemp at TROUBLESHOOTING
PROBLEM Cooler does not operate Cooler is not cold enoughTurns on and off frequentlyVibrations Cooler seems to make too much noiseDoor will not close properlyThe light does not work
POSSIBLE CAUSENot plugged in. Using wrong voltage. The circuit breaker tripped or there is a blown fuse. Check the temperature control setting; external environment may require a higher setting. The door is opened too often. The door is not closed completely. The door seal does not seal properly. The wine cellar does not have the correct clearances to operate efficiently and safely. The room temperature is hotter than normal. A large amount of contents has been added to the appliance. The door is opened too often. The door is not closed completely. The temperature control is not set correctly. The door gasket does not seal properly. Check to see that the wine cellar is level.The rattling noise may come from the flow of the refrigerant, which is normal. As each cycle ends, you may hear gurgling sounds caused by the flow of refrigerant in your unit. Contraction and expansion of the inside walls may cause popping and crackling noises. The appliance is not level. The wine cellar is not level. The doors were not properly installed. The seal is weak. The shelves are out of position. Not plugged in. The circuit breaker tripped or a blown fuse. The light switch is “OFF”.
732 South Racetrack Road, Henderson, Nevada 89015
13
Systems and other installed cooling units are parts only for 1 year, no labor. Self Contained WineMate Cooling Systems are 1 year parts, 1 year labor. Removal and reinstallation of cooling units is not included. Wine Accessories, Racking Systems, Parts and Other miscellaneous items is a 30 day warranty. Il Romanzo units: Warranty 90 (ninety) days. Replacement part 12 (twelve) months from the date of sale. Brama: 1 year warranty from date of purchase.Non-New Units (Scratch & Dent/Refurbished/Floor Models), warranty for compressor units is 90 days from your dated invoice and 30 days for thermoelectric units (parts for function only, not cosmetic defects). These units are refurbished and sold as is; Purchaser assumes risks to the quality and performance of goods and assumes the costs of all necessary service or repair not covered herein. Extended warranties via New Leaf may not be purchased on Non-New Units. Delivery is curbside. Upgrades in delivery will require an additional fee. Element Grills (via Element Products LLC), grills have a thirty day limited parts warranty on grill accessories. If a model is not listed here will have 90 day warranty on parts only if it’s a new item. Parts and Repairs: Warranty on in-house repairs: 90 days parts and labor for compressor; 30 days parts and labor for Thermoelectric; Customer is required to put down a labor deposit of $75 for Thermoelectric units; $150 for compressor based Wine Coolers and $195 for WineMate units which will be kept if a unit is found to be in good working condition. Customer is responsible for freight costs to us. Warranty on parts purchased: 30 days; if part fails within 30 days of purchase, customer is to ship us back the part; upon inspection, if defective, VT will send replacement part at no charge.If a purchaser claims a product is “defective” with regards to refrigeration, Purchaser must obtain a letter from a qualified refrigeration technician at the Purchaser’s cost to verify that the unit was installed properly, with proper ventilation and the unit is truly malfunctioning due to a manufacturing defect. Removal or reinstallation of a unit is not included in warranted costs. Purchaser’s exclusive remedy is limited at Seller’s option to repair or replace defective part[s] with either new or reconditioned part[s]. Purchaser is responsible for shipping the unit prepaid to a designated facility and Seller will pay return shipping charges in the continental United States for items repaired under warranty within 12 (twelve) months from date of sale. The returned unit must be packaged correctly, with enough protection to ensure the unit is not further damaged. Oversized or lack of packaging is not permitted and will be refused. Replacement or exchanged units will be returned to Purchaser through curbside delivery only. Any redelivery fees are the Purchasers responsibility. Since the natural variation in texture, density, grain, color, tone, and shade of wood is unavoidable; Seller does not guarantee the texture, color, tone, or shade of the wood: nor does seller guarantee the colorfastness of wood or against peeling, chipping, cracking, or scratching. Note: Unfinished wood is subject to warping; all wood surfaces must be sealed before placing cellar into service. Make sure doors are aligned by reviewing the owner’s manual. Improper repair or placement of the unit will void the warranty. Any third party repair facility must be preapproved in writing by Seller, before providing replacement parts under
732 South Racetrack Road, Henderson, Nevada 89015 7 3 2 S o u t h R a c e itnr vR ionaodt,eHmepn.dc eo rms o n , N e v a d a 8 9 0 1 5 i n f o @ v i n o t e m p . c o m
17 17
Any dispute or claim relating in any way to these to the Terms and Conditions, the Website, or any products or services sold or distributed by or through this Website, store, or catalog will be resolved by binding arbitration, rather than in court, except that you may assert claims in small claims court if your claims qualify. The Federal Arbitration Act and federal arbitration law apply to the Terms and Conditions. We each agree that any dispute resolution proceedings will be conducted only on an individual basis and not in a class, consolidated or representative action. If for any reason a claim proceeds in court rather than in arbitration we each waive any right to a jury trial. Both parties agree to bring suit in court to enjoin infringement or other misuse of intellectual property rights.The above terms and conditions are the only ones governing this transaction and Seller makes no oral representations of any kind. These Terms and Conditions can only be modified in writing, signed by both Purchaser and Seller.SPECIFIC WARRANTY BELOW for SCRATCH & DENT/OPEN BOX/ REFURBISHED/FLOOR MODELS/ CLOSEOUTS, OVERSTOCK: TERMS AND CONDITIONS OF SALEVinotemp (and its brands Element, Wine Mate, Cellar Tec, Apex Wine Racks, Epicureanist Il Romanzo, Brama(“Seller”) and the person of the entity that acquires these goods from Seller (“Purchaser”) hereby fully aggress to the following terms and conditions of the sale:1. Freight: Vinotemp is not a freight, moving or installation company, if Freight is arranged for the Buyer, the Seller assumes no responsibility for the goods sold to the Purchaser once the goods have left the Seller’s premises, including, but not limited to, late delivery by the moving carrier, or for events caused by any difficulty carrier incurs in attempting to fit the goods into the Purchaser’s place of business or residence due to the size of the goods or otherwise, such as the disassembly and reassembly of the goods. Purchaser assumes all responsibility for delivery, payment of freight, extra fees, access, measurement, installation, hook-up, moving and storage of the goods. The transportation of all goods is subject to the terms and conditions which the moving carrier imposes on Purchaser including, but not limited to, additional charges imposed per flight of stairs, and/or additional charges resulting from the carrier’s inability to safely and/or adequately use the building elevator to lift the goods to an upper floor. Any claim for damages incurred during shipment by the carrier of the goods are insured and handled directly with the carrier and must be noted at time of delivery.2. All sales are final, and unless authorized in writing by the Seller, Purchaser is not entitled to return goods, under any circumstances. If Purchaser refuses to accept goods, the Purchaser is liable for the return and cost of freight both directions and a restocking/service fee that is 35% of the purchase price of the goods. Purchaser must notify Seller of non-conforming goods within four days of delivery, after which time all goods are deemed accepted.3. If Purchaser tenders payment with a check that has insufficient funds (NSF), or stops payment on a check or credit card for any reason, Purchaser agrees to pay for all costs associated with the Seller’s connection or litigation of such a claim, including without limitation
732 South Racetrack Road, Henderson, Nevada 89015 7 3 2 S o u t h R a c e itnr vR ionaodt,eHmepn.dc eo rms o n , N e v a d a 8 9 0 1 5i n f o @ v i n o t e m p . c o m
19 19
[xyz-ips snippet=”download-snippet”]