Energizer 58822 Wireless Switch LED Puck Lights Instruction Manual

Energizer 58822 Wireless Switch LED Puck Lights Instruction Manual

LED PUCK

BATTERY INSTALLATION

  1. Turn the back cover of the puck counterclockwise and remove it.
  2. Insert 3 AA batteries, noting polarity. Replace the cover and turn it clockwise.

MOUNTING INSTRUCTIONS

  1. Use the included screws or double-sided tape to mount the back cover. Make sure the mounting surface area is clean and dry before mounting with the double-sided tape.
  2. To install the puck using screws, take off the back cover and insert the screws through  the holes. Do not overtighten.

NOTE: The puck’s back cover may remain mounted when changing batteries.

WALL SWITCH

BATTERY INSTALL AND REPLACEMENT

  1. The battery comes pre-installed. To activate for use, pull out the battery tab.
  2. To replace battery, slide and remove the battery door from the back of the wall switch.
  3. Replace with one A23 battery – noting polarity.
  4. Replace the battery door of the wall switch and ensure it is firmly closed.

SWITCH INSTALLATION

  1. Remove the back mounting plate from the wall switch by sliding the wall switch remote upwards
  2. Install the mounting plate using included screws through the mounting plate. Do not overtighten.
  3. Mount the wall switch onto the mounting plate by gently sliding it downward to secure  it in place.

SWITCH OPERATION

  • Press up on the switch to turn the light ON, press down to turn the light OFF.

NOTE: There is a 60min. timeout feature that will turn the light OFF to conserve battery life. The wall-  switch remote will control all Energizer Wireless Switch LED Puck Lights (58822) within a 50-foot range.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC STATEMENT

Suppliers Declaration of Conformity | Model #: 58822 | Jasco Products Co., 10 E. Memorial Rd., Oklahoma City, OK 73114, www.byjasco.com

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device must not be co-located or operating in conjunction with any other antenna or transmitter.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that  interference will not harmful interference to radio or television reception, which can be occur in a particular installation. If this equipment does cause determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.To comply with FCC’s RF radiation exposure limits for general population/uncontrolled exposure, this device must be installed to provide a seperation distance of at least 20cm from all persons.

WARNING: changes or modifictions to this unit not expressly approved by the party resposible for compliance could void the user’s authority to operate the equipment.

WARNING

  • BATTERIES MAY LEAK HARMFUL  LIQUIDS OR IGNITABLE MATERIALS OR EXPLODE CAUSING INJURY AND PRODUCT DAMAGE
  • DO NOT MIX OLD AND NEW OR OTHER BATTERY TYPES
  • REPLACE ALL BATTERIES AT THE  SAME TIME
  • REMOVE BATTERIES IF PRODUCT IS TO BE UNUSED FOR EXTENDED PERIODS OF TIME

MADE IN CHINA/HECHO EN CHINA

©2021 Energizer. Energizer and certain graphic designs are trademarks Brands, LLC and related subsidiaries and are used under license by Jasco Products Company, LLC.

Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between7AM-8PM, M-F, Central Time.

report this ad

90-day warranty. Visit www.byjasco.com for warranty details

 

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,