ENFORCER SL-1311-MA High Intensity 1Wx4 Blue LED Module User Manual

ENFORCER SL-1311-MA High Intensity 1Wx4 Blue LED Module User Manual

Features

  • 4 High intensity 1-watt LEDs
  • Synchronize up to 20 units
  • 23 Different programmable flash patterns
  • Waterproof (IP67) and vibration-resistant
  • Operating life rated 100,000 hours
  • Flexible input power (10~30 VDC)

Parts List

  • High Intensity 1W LED Module: x1
  • Mounting flange: x1
  • Mounting screws: x2
  • Manual: x1
  • Rubber gasket: x1

Introduction

The ENFORCER SL-1311-MA/B is a High Intensity 1Wx4 LED Module strobe light that features next generation LED technology with four 1-watt LEDs in a very compact package.This strobe light offers 23 selectable flash patterns, potted circuitry to be waterproof (IP67) and vibration-resistant, multi-unit synchronization (simultaneous or alternating), and 10~30 VDC operating voltage, making it excellent for a wide range of security and informative applications.

Specifications

Housing shape Rectangular
Number of LEDs 4 High intensity 1W LEDs
Current draw* 56 /
Operating voltage 10~30 VDC
Electrical protection Reverse polarity protected
Operating life LEDs rated at 100,000 hours (>11 years)
Number of flash patterns 23 (programmable)
Synchronization Simultaneous or alternating up to 20 units
IP Rating IP67
Operating temperature 22°~150° F (-30°~65° C)
Dimensions 413/16″x15 /8″x11 /8″ (122x41x29 mm)
  • Figures shown are maximums. Current draw will vary depending on flash pattern.

Dimensions

Wiring and Installation

Wiring the strobe
  1. Black wire: Connect to power supply negative (-) terminal or ground.
  2. Red wire: Connect to power supply positive (+) terminal 10~30 VDC.NOTE: It is recommended to fuse each unit @ 1A.
  3. Yellow wire:
    • Programming Flash Patterns: Connect an optional SPST momentary switch such as ENFORCER SS-032Q to program the strobe light flash patterns. See connection diagram above, and Flash Patterns on page 4 for more instructions.
    • Synchronizing Multiple Units: Connect the yellow wires of multiple units to synchronizetheir flash patterns.NOTE: All units must be set to the same flash pattern.
    • Connect the yellow wires of additional units to synchronize up to 20 strobes.
  4. White wire (optional to set alternating flash):
    • Alternating Flash: Strobes can synchronize in an alternating flash pattern. For example, when Strobe A flashes ON, Strobe B will flash OFF, etc. Synchronize all strobes. Connect the white wire to the power supply only for strobes that should alternate with the others.
Mounting the strobe
  1. Choose a mounting surface and drill a hole large enough to allow strobe wires to pass.
  2. Feed the wires through the hole in the rubber gasket and the mounting surface.
  3. Place the mounting flange over the LED module. Check that it is properly seated on the rubber gasket and that the gasket and mounting surface form a seal to maximize weather resistance.
  4. Align the holes in the gasket and flange and use the self-tapping screws to secure unit in place.

Mounting Accessories: (not included)SL-1311SM: Replacement plastic mounting flange for SL-1311-MA/B.

Flash Patterns

  1. LEDs are grouped into two sets, Set 1 and Set 2.The left pair of LEDs are Set 1; right pair of LEDs are Set 2.
  2. To change patterns, momentarily connect the strobe’s yellow wire to +VDC:Each connection to power will move to the next pattern.Hint: Use a programming switch (not included)—see Wiring and Installation on page 3.

 

  1. After changing, the flash pattern will first run one time, pause, then begin repeating.
  2. Internal memory will retain last setting when power is disconnected.

    Pattern #

    Flash pattern

    1

    Single (2Hz)

    2

    Double (2Hz)

    3

    Triple (2Hz)

    4

    Quad (2Hz

    5

    Randomly cycles all patterns
    Alternates between Set 1 LEDs and Set 2 LEDs

    6

    Single flash each set

    7

    Double flash each set

    8

    4x flash each set

    9

    5x flash each set

    10

    Rapid flash with fast alternation

    11

    Ultra rapid flash with slow alternation

    12

    Pattern 6 / Pattern 8

    13

    Pattern 6 / Pattern 10
    All LEDs light together

    14

    Single flash

    15

    Double flash

    16

    4x flash

    17

    5x flash

    18

    Rapid flash

    19

    Bursts of ultra rapid flash

    20

    Pattern 14 / Pattern 16

    21

    Pattern 14 / Pattern 18
    Other

    22

    Set 1 steady ON; Set 2 double flash

    23

    All LEDs steady ON

California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

WARRANTY

This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.Copyright © 2021 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

SECO-LARM® U.S.A., Inc.16842 Millikan Avenue, Irvine, CA 92606

report this ad

Tel: 800-662-0800 / 949-261-2999Fax: 949-261-7326Website: www.seco-larm.comE-mail: [email protected]

 

References

[xyz-ips snippet=”download-snippet”]


Posted

in

by