ErGear Monitor Desk Mount EGDS2 Instruction Manual

Monitor Desk MountInstruction ManualModel: EGDS2

Thank you for choosing this Ergear product! At Gear, we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact at [email protected] (US/CA/DE/UK/FR/IT/ES/AU)

IMPORTANT SAFETY INFORMATION

Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our customer service at [email protected].CAUTION: Avoid potential personal injuries and property damage!

• Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
• This product contains a high-pressure gas spring, fire and percussion are prohibited. Also, it is strictly prohibited to dismantle without professionals. Please return to the manufacturer or hand it over to professional agencies if the product is abandoned.
• The desk must be capable of supporting three times the weight of the total load (the mount, the monitor, and all accessories weight). Don’t use the product on particleboard.

Weight Restrictions

Your monitor (including accessories) CANNOT EXCEED 6.6-26.4lbs (3-12 kg)

WARNING

DO NOT exceed the maximum weight indicated. This mounting system is intended for use only with the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage and or injury.If your monitor weighs more, this mount is NOT compatible.Check the VESA Pattern of Your Monitor before You Begin the Installation

If your Monitor VESA is greater than 100×100 mm/4×4 in. or less than VESA 75x75mm/3x3in., this mount is NOT compatible.If this desk mount is NOT compatible, please contact customer service at [email protected] to find a compatible product.

Product Features

TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MOUNT INSTALLATION

WarningDo not adjust tension without a monitor.

1. Ensure the monitor has been attached to the mount.
2. Read your monitor box or manual to find out the monitor net weight.
3. Ensure the net weight of the monitor (including accessories) is between 6.6~26.4 Ibs (3-12 kg).

Parts and Hardware Included

Install the BaseA. For Clamp Mounting A-1 Install the USB Cable and C Clamp to the Base

1. Install the USB cable [07] to the base [05]
2. Connect part [03] to base [05]
3. Install part [04] to part [03]Warning: Ensure bolts are secured firmly

A-2 Secure the Base to the Desktop

B. For Grommet MountingB-1 Install the USB Cable and Grommet Bolt to the Base

B-2 Secure the Base to Desktop Using Locking Plate and Butterfly Nut

Install the Arms

Install the Monitor Plates

Attach Monitors to the Arms

4-1 Choose Proper Bolts

4-2 Install Monitors to the Arms

Screwdriver [Not Included]

The tension is preset at 8.8-11 LBS(4-5kg). After hanging the monitor to the mount, please release the monitor slowly to prevent it from falling suddenly.

Adjust Gas Spring Tension

Be sure to keep the arm in a horizontal position during adjustment. Or else, it would be difficult to adjust the mount or damage the mount. .

1. If the monitor can stay at the desired height by itself, no adjustment is needed.
2. If the monitor rises up, press the arm to keep it in horizontal position and then use the 13/64 in. (5mm) Alley key (F) to turn the bolts clockwise(“-” direction) to reduce the tension of the arm only until the monitor can stay at the desired height by itself.
3. If the monitor falls down, lift the arm to keep it in horizontal position and then use the 13/64 in. (5mm) Alley key (F) to turn the bolts counter-clockwise(“+” direction) to increase the tension of the arm only until the monitor can stay at the desired height by itself.

Rotation Restriction

Tilt Adjustment

Adjust the monitor to proper tilt angle, using Allen key (F) to tighten the bolt and fix tilt angle

Route Cables along the Arms

8-1 Route cables along the arm [01]

8-2 Route cables along with the arm extender [02]

Thank you again for choosing this Ergear product!

All of us at Ergear do appreciate your product purchase. We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us at [email protected] (US/CA/DE/UK/FR/IT/ES/AU)