EUFYCAM 2C Pro Wire-Free 2K Security Camera Set User Guide

EUFYCAM 2C Pro Wire-Free 2K Security Camera Set User Guide

GETTING STARTED

For HomeBase 2 Installation

HomeBase 2(T8010)

Power Adapter for HomeBase 2

Ethernet Cable

Metal Pin for Resetting

For eufyCam 2C Pro installation

eufyCam 2C Pro(T8142)

Micro-USB Charging Cable

Mounting   Bracket

Mounting Screws and Anchors

  1. Camera quantity and accessories vary by bundle package.
  2. HomeBase 2 power adapter varies by region.

PRODUCT OUVERVIEW

HomeBase 2
  1. Status LED
  2. Speaker
  3. Power port
  4. USB port
  5. Ethernet port
  6. SYNC/ALARM OFF button
  7. Reset button
eufyCam 2c Pro
  1. Lens
  2. Light sensor
  3. Microphone
  4. Motion sensor
  5. Spotlight
  6. Status LED
  7. SYNC button
  8. Mounting hole
  9. Charging port
  10. Speaker

CONNECTING THE HOMEBASE 2

Connect the HomeBase 2 to the Internet
  1. Power on the HomeBase 2, then use the ethernet cable provided to connect the HomeBase 2 to your home router.
  2. The LED indicator turns blue (this may take up to I min) when HomeBase 2 is ready for setup.

SETTING UP THE SYSTEM

Download the App and Set up the System

Download the eufy Security app from the App Store (10S devices) or Googje Play (Android devices).

Sign up for a eufy Security account, then follow the onscreen instruc-tions to complete the setup.

MOUNTING THE CAMERA

Find a Good Mounting Spot

To find a spot to mount eufyCam 2C Pro, you need to test wireless signal strength.

  1. Open the eufy Security app, go to Camera Settings > Mounting Guide. 12)
  2. To test the wireless signal strength, take your camera and phone to the location where you want to mount the camera.
  3. Move the camera as close to the HomeBase 2 as possible if the wireless signal strength is poor.
Select Height and Location

Hang eufyCam 2C Pro 7-10 ft (2-3 m) above the ground.This height maximizes the detection range of the motion sensor of eufyCam 2C Pro. Avoid placing eufyCam 2C Pro under direct sunlight.

Mount the camera

The camera can be mounted both indoors and outdoors.

  1. Tum the knob of the mounting bracket docicwise to loosen and disassemble it.
  2. Drill holes with a 15/64 inch (5.95mm) drill bit, then insert the anchors  into the holes; anchors are necessary for walls that are made out of hard materials such as concrete, brick, or stucco.Mount the camera
  3. Firmly screw the base of the mounting bracket onto the wal. Fasten the ball knob of the bracket to the base of the bracket.
  4. Tighten eufyCam 2C Pro to the mounting bracket and adjust the viewing angle by checking the live stream feed in the eufy Security app.

Tips:

  1. The Homebase 2 pairs up to 16 cameras, you can repeat the steps mentioned above to add more eufyCam 2C Pro cameras to meet different needs of use.
  2. For troutieshooting,check He on the euff Security App.

CHARGING EUFYCAM 2C PRO

Charge eufyCam 2C Pro

Method 1

Method 2

LED indication

 Charging: Steady blue
Fully charged: Off

Charging time

 5 hours

NOTICE

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (I) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ( I) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receive: (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure StatementThe device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure conclusion. The min separation distance is 20cm.

Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

The following importer is the responsible party Company Name: POWER MOBILE LIFE, LLC Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004 5541 Telephone:1-800-988-7973

This product complies with the radio interference requirements of the European Community.

Declaration of ConformityHereby Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 20 I 4/53/EU. For the declaration of conformity, visit the Web site www.eAflife.com Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher: The adapter shall be installed near the equipment and shall be easily accessible. Do not use the Device in the environment at too high or too low temperature. never expose the Device under strong sunshine or too wet environment. The suitable temperature for HomeBase 2 and accessories is -I 0°C-45°C. The suitable temperature for eufyCam 2C Pro and accessories is -20°C-50°C. When charging, please place the device in an environment that has a normal room temperature and good ventilation.It is recommended to charge the device in an environment with a temperature that ranges from 5°C-25°C. Please ensure to use only the charger offered by the manufacturer Using unauthorized charger may cause danger and violate the authorization of the device and the guarantee article. This charger is for indoor use only The charger type is ASSA67W-I 20200, output voltage/current is I 2Vdc/2A.The plug considered as disconnect device of adapter. RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body.

CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Wi-Fi Operating Frequency Range: 24I2-2972MHz ; Wi-Fi Max OutputPower: 17.13 dBm (ERIP for T8010), 17.9 dBm (ERIP for T8142) SUB-1G Frequency range: 866-866.8MHz SUB-1 G Output Power:5.492 dBm (ERIP forT8I42).

The following importer is the responsible party (contact for EU matters only) Importer: AnkerTechnology (UK) Ltd Importer Address: Suite B, Fairgate House, 205 Kings Road,Tyseles Birmingham, BI 2AA United Kingdom.

This product is designed and manufactured with high quality materials and components, which can be recycled and reused.

 This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

IC StatementThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (I) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.” Le present appareil est conforme aux CNR d’Industrie Canada applicables aux apparel’s radio exempts de licence. L’exploitation est autorisee aux deux conditions suivantes: (I) l’appareil nedoit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, me’me si le brouillage est susceptible d’en compromettre le fonctionnement.” This Class B digital apparatus complies with Canadian ICES-003.

IC RF StatementWhen using the product. maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de (‘utilisation du produit maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matiere d’exposition RF.

LEGAL NOTICE

Use of the Works with Apple HomeKit badge means that an electronic accessory has been designed to connect specifically to iPod touch, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards.Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

Customer Service

Warranty12-month limited warrantyCall UsUnited States +1 (800) 988 7973 Mon-Fri 9AM-5PM (PT)United Kingdom +44 (0) 1604 936 200 Mon-Fri 6AM- I I AM (GMT)Germany +49 (0) 69 9579 7960 Mon-Fri 6:00-11:00Email UsCustomer Support: [email protected]Anker Innovations LimitedRoom 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

 

report this ad

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, ,