EVENT LIGHTING LM7X30 7X30W LED RGBW Zoom Wash Moving Head
For safety, please read this user manual carefully before initial use.Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.
Version: 1.0 (revised 05/11/2020)
Safety Instructions
Warning
- Do not open this device, there are no user-serviceable parts inside. Risk of electric shock.
- Do not look at the light source when the device is on.
Caution: This unit’s housing may be hot during and after operation.
- Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
- Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
- Use a safety chain when mounting this device overhead.
- Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
- Do not operate this device if the housing, lenses, or cables appear damaged.
- Do not connect this device to a dimmer or rheostat.
- ONLY connect this device to a grounded and protected circuit.
- ONLY use the hanging bracket to carry this device.
- In case of a serious operating problem, stop using immediately.
- The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power LinkingThis device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Fuse ReplacementIf the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating. Before replacing the fuse, unplug mains lead.
Procedure:Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).Step 2: Remove the old fuse from the fuse holder.Step 3: Install the new fuse in the fuse holder.Step 4: Replace the fuse holder in the housing and fix it.
Product Installation
- This device can be mounted in many orientations provided each individual device is secured by the use of correct mounting bracket.
- Use a safety chain when mounting this device overhead.
Dimensions
Lux Chart
Menu – Move up a level.Up – Move selection up one item.Down – Move selection down one item.Enter – Select / Move down a level.
| MENU | DESCRIPTION | ||
| DMX
(Function Mode) |
DMX Address | A001~AXXX | DMX Address Setting |
| Channel Mode | CH17 | 17 Channel Mode | |
| CH15 | 15 Channel Mode | ||
| Auto Run | Program 1~8 | Master/Alone | Auto Run State |
| Music Run | Program 1~8 | Master/Alone | Music Control State |
| SET
(Fixture Set) |
Reset Default | Yes/No | Reset to Default Setting |
|
Signal Set |
DMX
Wireless DMX Wireless TX |
Wired DMX
Wireless DMX Receiver Wireless DMX Transceiver |
|
| Reverse Pan | (On/Off) | Reverse Pan | |
| Reverse Tilt | (On/Off) | Reverse Tilt | |
| Select Pan | 630°/540°/360° | Select Pan (Default 540°) | |
| Select Tilt | 270°/180°/90° | Select Tilt (Default 270°) | |
| Mic Sens. | 0~99% | Microphone Sensitivity Setting | |
| Hold on no | (On/Off) | Hold or no hold when no Signal | |
|
Limit Mode |
OFF/Center/Right/Left |
Select Edge or Corner Range | |
| MAN
(Manual) |
Reset |
All Pan/Tilt Zoom | Reset all Settings Reset Pan/tilt Settings Reset Zoom Settings |
| Channel | PAN=XXX…… | Manual Control Channel | |
| ADV
(Advanced) (Access Code 088) |
Calibration | PAN=XXX…… | Calibration |
The default selection for each setting is highlighted.
DMX Chart
| Mode/Channel | Value | Function |
| 17 | 15 | |
| 1 | 1 | Dimmer |
| 0..255 | Dimmer 0%…100% | |
| 2 | 2 | Shutter |
| 0..31 | Shutter closed | |
| 32..63 | Shutter open | |
| 64..95 | Strobe effect slow to fast | |
| 96..127 | Shutter open | |
| 128..159 | Pulse effect, slow to fast | |
| 160..191 | Shutter open | |
| 192..223 | Random strobe effect, slow to fast | |
| 224..255 | Shutter open | |
| 3 | 3 | Pan |
| 0..255 | PAN Movement | |
| 4 | Pan Fine | |
| 0..255 | Fine control of Pan movement | |
| 5 | 4 | Tilt |
| 0..255 | Tilt Movement | |
| 6 | Tilt Fine | |
| 0..255 | Fine control of Tilt movement | |
| 7 | 5 | Zoom |
| 0..255 | In(near) to out(far) | |
| 8 | 6 | Speed pan/tilt |
| 0..225 | Pan/tilt speed, fast to slow | |
| 226..235 | Blackout during pan/tilt functions | |
| 236..255 | TBD | |
| 9 | 7 | Red |
| 0..255 | Red 0-100% | |
| 10 | 8 | Green |
| 0..255 | Green 0-100% | |
| 11 | 9 | Blue |
| 0..255 | Blue 0-100% | |
| 12 | 10 | White |
| 0..255 | White 0-100% | |
| 13 | 11 | Macro |
| 0..15 | TBD | |
| 16..31 | Red | |
| 32..47 | Green | |
| 48..63 | Blue | |
| 64..79 | White | |
| 80..95 | Red+Green | |
| 96..111 | Red+Blue | |
| 112..127 | Red+White | |
| 128..143 | Green+Blue |
| 144..159 | Green+White | |
| 160..175 | Blue+White | |
| 176..191 | R+G+B | |
| 192..207 | R+G+B+W | |
| 208..223 | Jump effect | |
| 224..239 | Fading effect | |
| 240..255 | Pulse effect | |
| 14 | 12 | Macro Speed |
| 0..255 | Macro speed from slow to fast | |
| 15 | 13 | Colour Temp |
| 0..15 | TBD | |
| 16..45 | Below 3200K | |
| 46..75 | 3200K – 3500K | |
| 76..105 | 3500K – 5000K | |
| 106..135 | 5000K – 5500K | |
| 136..165 | 5500K – 6000K | |
| 166..195 | 6000K – 6500K | |
| 196..225 | 6500K – 7000K | |
| 226..255 | 7000K – 8000K | |
| 16 | 14 | Visual Tungsten Lamp |
| 0..15 | TBD | |
|
16..255 |
Tungsten lamp effect is gradually enhanced |
|
| 17 | 15 | Special function |
| 0..19 | TBD | |
| 20..39 | TBD | |
| 40..59 | TBD | |
| 60..79 | TBD | |
| 80..84 | Reset all | |
| 85..94 | Reset scan | |
| 95..99 | Reset zoom | |
| 100..109 | Internal program 1 | |
| 110..119 | Internal program 2 | |
| 120..129 | Internal program 3 | |
| 130..139 | Internal program 4 | |
| 140..149 | Internal program 5 | |
| 150..159 | Internal program 6 | |
| 160..169 | Internal program 7 | |
| 170..179 | Internal program 8 | |
| 180..189 | Internal sound program 1 | |
| 190..199 | Internal sound program 2 | |
| 200..209 | Internal sound program 3 | |
| 210..219 | Internal sound program 4 | |
| 220..229 | Internal sound program 5 | |
| 230..239 | Internal sound program 6 | |
| 240..249 | Internal sound program 7 | |
| 250..255 | Internal sound program 8 |
The device is controlled by universal DMX 512 protocol, DMX address is the start channel used to receive instructions from the external controller. For independent control, each fixture must be assigned its unique address control channels. For example, this device has two channel modes:15/17, if we set the mode at standard 17 channels mode, and there are several models need to be independently controlled, we just simply address first fixture at 1, and second fixture at 18, third one at 35, etc.
- If the devices have the same address, they will behave synchronically.
- Display is flashing when no DMX signal is received.
More Functions
- Software upgrade function via DMX cable. If there is any new firmware for this device, it can be upgraded simply via a software upgrade box, without the need to change any mechanical parts. The upgrade box is not included in the package, if you need any further assistance please contact your authorized dealer.
- Hibernation. The device will enter sleep mode if activated after a period of disconnecting DMX signal to save power and will wake immediately when the DMX signal is sent or received again.
Technical Specifications
Photometric
- Light Source: 7pcs 30W RGBW LEDs
- Beam Angle: 6°~60°
- Output: 19,130lux @ 3m @ 6°
- PWM: 1,000Hz
- LED Lifespan: 50,000hours
Effects
- Dimming: 0~100%
- Strobe: 1.4~21Hz
- Zoom: 6°~60° linear via DMX
Movement
- 8/16 – bit, auto-reposition
- Pan: 360°/540°/630°
- Tilt: 90°/180°/270°
- Limit mode: Centre/Corner/Edge
Power
- Input Voltage: 90~260V AC, 50/60 Hz
- Power Consumption: 240W
- Connection: PowerCon in
- Fuse: F4A, 250V
Control
- Protocol: DMX512
- Operation Modes: DMX, manual, auto, sound active, master/slave
- DMX Channels: 15/17
- Interface: 3-pin XLR in/out
- Built-in Programming: Yes
- Sound Active: Yes
- Display: 4-button 1.8inch TFT LCD display control panel
Housing
- Materials: Metal & flame retardant ABS
- Finishing: Matte black
- IP rating: IP20
- Cooling: Fan
- Net Weight: 6kg
- Rigging: 1pc omega brackets with 1/4- turn quick locks
WarrantyPlease refer to your local dealer or contact Event Lighting Pty Ltd.
References
[xyz-ips snippet=”download-snippet”]