FARSEEING Fluorescent Soft Light User Manual

Fluorescent Soft LightFD-S4,55DMXFD-S6`55DMX

Description:

Characteristics &Applicability

• The light beam is soft, symmetrical, comforts eyes and there is no radiant heat occurred.
• The super-efficiency reflection mirror and reflective barn doors enable the light energy to be fully used.
• With wonderful color reducibility, the Color Rendering Index (Ra) of the light tube is up to 80-90. It will achieve a better effect when being used together with tungsten light.
• Equipped with a high-efficiency tube of a well-known brand, which gets at least 70-80InVvatt, with long We, and can be used up to 1000 hours.
• It adopts high-tech energy-saving electronic parts, which can save at least 70% of
• Sockets of tubes comply with the international security standard. The light adopts the world’s best high-efficiency energy-saving electronic ballast which features a low wave crest low noise, safety, and reliability. Furthermore, it can add a dimming function as per the user’s requirement, the scope of light dimming is with a wide range and the color temperature is invariable.
• FD-S series lights are suitable for middle and small studios, meeting-room esp. for News-Broadcasting studios and the imaginary studios.

Structural Characteristics & Adjustable Scope:

1. Configuration sketch of FD-S4X55W:1. Light tube 2. Light yoke 3. Hanging connector 4. The socket of the tube 5. Locking handle of yoke 6. Power supply socket 7. The located button of barn doors 8. Reflective barn doors 9. Lamp controlling knob Dimmer (Type A)
2. Pitching adjustment of light fixture

• Loosen locking handle 5 to adjust the pitching angle of the light fixture.
• To make an aesthetic effect, set the locking handle at 360 degrees adjustable, pull outward the coat of the locking handle when doing the adjustment, and loosen it when getting the satisfying angle you required.
• Installation of barn doors: Release located button of bam doors 7 at an upper position of light fixture, insert barn doors along with block slot of one end and the other end of light fixture, when this work is ok, screw button 7 tightly in order to prevent barn doors from falling off.

Product Introduction

1. Board introduction
2.  Working mode introductionDMX512 signal control dimming mode uses the DMX512 digital console to control the brightness of the light.
3. DMX Address Setting Method Each encoder occupies 3 DMX addresses, using the coding switch to set the address. The coding switch 1-9 is setting the DMX512 starting address of binary numeric code switch, ‘1″ lowest bit,’9’ highest bit. Total can set 511 address codes. DMX512 starting address equal to the sum of the coding switch 1-9’s bit value. Switch down the encoding (ON set as “1”), it can obtain this bit value; Switch up (“0”), this bit value is “0”.Note: The coding switch FUN (10) equal to OFF (set as “0”) can accept the DMX512 signal function.Example 1: As Figure 1, DMX512 starting address set as “37”, dial the encoding switch “6”,”3″71″ to “1”, others set to “0”, then the sum of encoding switch 1-9′ bit value is ’32 +4 +1″, that means the start address DMX512 the is “37”.

Example 2: As Figure 2, DMX512 starting address set to “328”, dail the encoding switch “9′,”7″,”4” to “1”, others set to “0”, the sum of encoding switch 1-9′ bit value is ‘256 +64 +8″, that means the start address DMX512 the is “328”.

IV.Usage cautions:

1. When opening the package, please install Hanging connector 3 and Light yoke 2 together by 010 even gaskets, elastic gasket, m10 nut, friction mat, and install together locking handle 5 as sketch 1 indicates.
2. There is a layer of protective film on the reflector and the glistening plate of the barn doors. It must be removed before being put into use.

Nanjing Farseeing Science &Technology Co., LtdAdd: #68 Hengtong Avenue, Xingang ETDZ, Nanjing, ChinaTel : +86 — 25-86642611 125-84410776Fax: + 86 — 25-84527011E-mail: [email protected]

http://www.farseeingvideo.com