FEIT Electric DOME13-4WY-WH 13 Inch White Round Ceiling Fixture Instruction Manual
Safety Information
WARNING: RISK OF SHOCK House electric current can cause painful shock or serious injury unless handled properly.
For your safety, always remember to:
- Turn off the power supply at the fuse or circuit breaker box before you install the fixture.
- Ground the fixture to avoid potential electric shocks and to ensure reliable starting
- Double-check all connections to be sure they are tight and correct
- Wear rubber soled shoes and work on a sturdy wooden ladder.
This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, consult a qualified electrician or local electrical inspector, and check your local electrical code.
CAUTION: TURN OFF THE MAIN POWER AT THE CIRCUIT BREAKER BEFORE INSTALLING THE FIXTURE, IN ORDER TO PREVENT POSSIBLE SHOCK.
GENERAL: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions.
WARNING: RISK OF CUTS. Some metal parts in the fixture may have sharp edges. To prevent cuts and scrapes, wear gloves when handling the parts.
Account for small parts and destroy packing material, as these may be hazardous to children.
SAVE THESE INSTRUCTIONS
Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information
Responsible Party:Feit Electric Company4901 Gregg Road, Pico Rivera, CA 90660, USA562-463-2852Unique Identifier: DOME13/4INY/WH
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAN ICES-005 (B).
Limited Warranty
This product is warrantied to be free from defects in workmanship and materials for up to 5 years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at [email protected], visit feit.com/contact-us or call 1-866-326-BULB (2852) for instructions on replacement or refund.REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED.Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Pre-Assembly
TOOLS REQUIRED
- Phillips Screwdriver
HARDWARE INCLUDED
Note: Hardware not shown to actual size.
| Part | Description |
Quantity |
|
AA |
Fixture Housing |
1 |
| BB | Glass Lens |
1 |
| CC | Mounting Plate |
1 |
|
DD |
Wire Connectors |
3 |
| EE | Fixture Mounting Screws |
2 |
|
FF |
Outlet Box Mounting Screws |
2 |
| GG | Finials |
2 |
Installation
Turning Off the PowerTurn the power OFF at the switch and fusebox or the circuit breaker.
Unpacking of FixturesCarefully unpack and unwrap fixture (AA) and glass Lens (BB).
Removing Glass LensRemove the Glass Lens (BB) if attached to the Fixture Housing (AA). Turn the Glass Lens (BB) counter-clockwise and gently raise the glass up.
Setting the Mounting PlateInsert the Fixture Mounting Screws (EE) into the Mounting Plate (CC) and secure by tightening the included Screw Nuts against the Mounting Plate (CC).
NOTE: Make sure the Fixture Mounting Screws (EE) do not protrude too much or too little from the Mounting Plate (CC). You may need to adjust them to the proper length. Once the proper length is determined, tighten with nut to secure screws against the Mounting Plate (CC).
Installing the Mounting PlateSecure the Mounting Plate (CC) to the outlet box by inserting the two Outlet Box Mounting Screws (FF) through the slots in the Mounting Plate (CC).
Connecting the WiresLift the Fixture Housing (AA) to the outlet box. Connect the green wire or bare copper ground (house) wire to the ground screw on the Mounting Plate (CC). If the outlet box is grounded, you may fasten the fixture ground wire directly to the outlet box. Using the Wire Connectors (DD) provided, connect the white fixture wire to the neutral supply wire. Connect the black fixture wire to the power supply wire.
Install the Fixture HousingTuck the wires into the outlet box and lift the Fixture Housing (AA) over the Fixture Mounting Screws (EE) through the fixture housing holes and secure it by hand tightening the Finials (GG) to the ends of the Fixture Mounting Screws (EE).
NOTE: Hand tighten finials only. Do not use any tools as overtightening may occur causing damage to the fixture housing.
Select Color TemperaturesPick your favorite light color temperature before installing the Glass Lens (BB). See the page with Color Changing Instructions.
Install GlassSlide the Glass Lens (BB) into the Fixture Housing (AA) and secure by turning the Glass Lens (BB) clockwise.
Color Changing Instructions
report this ad
PICK YOUR FAVORITE LIGHT COLOR BEFORE INSTALLING
- You can lock in one color temperature or change among multiple color temperatures, it will memorize the last color temperature and reset automatically.
- When the Slide switch is set to SW (Soft White), the color temperature is set at 3000K.
- When the slide switch is set to BW (Bright White), the color temperature is set at 4000K.
- When the slide switch is set to DL (Daylight), the color temperature is set at 5000K.
ADJUST YOUR LIGHT COLOR ANYTIME WITH A REGULAR WALL LIGHT SWITCH
- Set the slide switch on the middle of the fixture to SWITCH.
- Toggle your light switch ON and OFF within 0.5 – 3 seconds to cycle through the 3 different color temperatures.
- If the fixture is left OFF over 10 seconds then turned ON, the fixture will remember the last color temperature selected and will display that color when turned on again.
- The reset function is used when using multiple color selectable lighting products operating from the same light switch. In the event that multiple fixtures are not displaying the same color at the same time, the fixture must be RESET using your existing light switch. Simply toggle the wall switch ON and OFF 7 times, leaving it in the ON position for 1 second intervals. (Ex. with the fixture in the ON position, toggle the wall switch OFF then ON, leaving it ON for 1 second, then OFF then ON, leaving it ON for 1 second. (Repeat 7 times)
Customer Service
Questions, problems, missing parts? Before returning to the store,call Feit Electric Customer Service8 a.m. – 5 p.m., PST, Monday – Friday1-866-326-BULB (2852)FEIT.COM
[xyz-ips snippet=”download-snippet”]