LED Gobo Moving Head
LED GOBO MOVING HEADUser Manual(Engllsh/Fran~als/ Espal’lol/ lingua ltallana/ Deutsch) Please read the Instructions carefully before useS’II vous plait lire attentlvement les Instructions avant d’utillser Par favor, lea las lnstrucclones culdadosamente antes de userSi prega di leggere attentamente le lstruzlonl prim!! dell’uso Bitte lesen Sle die Anweisungen sorgf!lltig var Benutzung
General instructions7 Thank you for choosing our company’s products. In order to use th device safely and q~ickly, .please read the user manual carefully before using the device and install or use the device 1n stnct accordance with the requirements of the user manual. If you have any questions during the use, please feel free to contact us or the dealer; at the same time, you are welcome to provide valuable advice on our products, we will be happy to provide you with quality consulting and after-sales service, thank you.Allachments:1 . LEO Miri bearn/Gobo Moving head Light: 1pcs 2 . PoM!r cable: 1pcs 3. Brackei: 1pcs, Screw: 2pcs 4 . User Guide: 1pcs
Notice:
1. Befcre using the device, please unpack and double check for shipping damage.
2. Cuskmers should carefuUy read the User Manual before using the equipment and operate the equipment in strict accordance wtth the requirements of the User Manual. Any damage to the equipment caused by failure to follow the User Manual and human error is not covered by the warranty.
3. This tJtit can only be used indoors and in dry places. The maximum ambient temperature should not exceed 40’C.
4. When installilg the equipment, tt must be carried out by professional operators. The place where the equipment is placed must be well ventilated. The wall shouk:I be no less than 50 cm away from the surface of theeq”””””‘1-
5. Bef«e tumilg on the device, make sure that the device’s power supply voltage and frequency meet the device’s PCM9′ requirements.
6. Before stating the device, check the integrity of the power cord to ensure the surrounding environment is safe. Do not touch a,y wires durilg operation, otherwise there is a danger of electric shock.
7. Avoid any imnmately.
liquids, water or metal objects entering lhe equipmenl ff this happens, tum off the power
8. Do not use the device in a dirty or dusty environment, and pay attention to cleaning the device regularly.9. ff the fuse ollhe device needs to be replaced when it bums out, lhe same type of fuse must be used after lhe power Is turned off, and replaced by a professional lachnician.10. Do not open the deof,ce for repair, otherwise lhe equipment will be damaged or malfunction and will not be covered by lhe warranty.
11 . If the device is not used for a long time, disconnect the device from the power source.
~~:::;~:’,;’ lhe equipment needs to be transported again, please pack lhe equipment with the original packaging
13. When lhe light is on, do not look directly at lhe LED llghl. Technical Specification :
1, Applicable power: AC100-240V (50HZ / 60HZ) 2, LED light source: imported high-brightness LED while light .
3, Color: 8 colors 4, Focusing: manual focus 5, beam angle: 11 · 6, Pattern: 8 patterns, adjustable speed. 7, Horizontal / vertical rotation angle: horizontal 540 ·, vertical 230 ·. 6, strobe/ dimming: electronic variables. 9, electronic linear dimming: 0-100% 10, working mode: automatic, voice control, DMX512, master-slave. 11, channel mode: 9/11 two control channel mode. 12, Size: L · W · H = 285′ 210 · 275mm; 13, Weight: 3.6KG Panel description: 1. MENU: select program function 2. LCD display 3. The indicating light 4. DMX signal input 5. DMX signal output 6. The power input socket Menu function description
II
MENU
Addr Chnd Shnd
SLnd SoUn
512 9Ch 11Ch Sh 1Sh 2 Sh 3 Sh4 nASt SL 1 SL2 on oFF
DMXADDRESS CHANNEL MODESHOW 1-4MASTER MODE SLAVE 1 Mode SLAVE 2 Mode Audio control mode
Send blndPantiltLeddlSp teSt tenp rest
1-100 yes no yes no yes no on oFF dlSp dSIPAUTO TEST TEMPERATURE TEST RESET
Voice sensitivity setting BLACKOUT MODEHorizontal rotationRotate verticallyLED display DISPLAY NORMALInverted display
Function settings description[Addr] DMX512 address code settingSelect [Address]: Press the MENU button to display [Address] on the display. Then press theENTER button to enter the option. Press the down or up buttons to set the address to the·addresscode you need (1-512). After selecting the address, press the ENTER button to confirm the setting. Then press the MENU button for one second or wait one minute to exit the menu mode.[Chnd] channel settingsTo select the [ Chnd ): press the MENU button to show the [ Chnd Jon the display, Then press ENTER button to enter. Press the DOWN or UP button to select the 9 or 11 channel modes. Once the mode has been selected, press the ENTER button to setup, then press the MENU button forone second or wait for one minute to exit the menu mode.[Shnd] show mode settingTo select the [ Shnd J : press the MENU button to show the [ Shnd] on the display, Then press ENTER button to enter, press the DOWN or UP button to select the [ Sh 1 ] ( show 1),[ Sh 2 ] ,[ Sh 3 J or ( Sh 4 J(Show 4) mode. Once the mode has been selected, press the ENTER button to setup, then press the MENU button for one second or wait for one minute to exit the menu mode.[SLnd) slave mode settingTo select the ( SLnd J: press the MENU button lo show the [ SLnd) on the display, Then pressENTER button to enter, press the DOWN or UP button to select the [ nASt) ( MASTER), [ SL 1 ] ( SLAVE 1) , [ SL 2 J ( SLAVE 2) modes. Once the mode has been selected, press the ENTERbutton to setup, then press the MENU button for one second or wait for one minute lo exit the menu mode.
[SoUn] sound control mode settingSelect (SoUn]: Press the MENU button to display [SoUn] on the display, then press the ENTER button to enter. Press the down or up button to select [On] (sound control function on) or [oFF] (sound control off) mode. After selecting the mode, press the ENTER button to set, then press the MENU button for one second or wait one minute to exit the menu mode.[Send] sound control sensitivity settingTo select [Send]: Press the MENU button to display [Send] on the display, then press the ENTER button to enter. Press the down or up button to select the voice sensitivity (1-100]. After selecting the mode, press the ENTER button to set, then press the MENU button for one second or wait one minute to exit the menu mode.[bLnd) Closed light settingTo select the [ bLnd ]: press the MENU button to show the ( bLnd] on the display, Then press ENTER button to enter. press the DOWN or UP button to select the ( no ] (normal) or ( yes ] (close the lighting) mode. Once the mode has been selected, press the ENTER button to setup, then press the MENU button for one second or wait for one minute to exit the menu mode.[PAn) X-axis forward or reverse rotation settingTo select the [PAn ]: press the MENU button to show the ( PAn] on the display, Then press E_NTER button to enter. Press the DOWN or UP button to select the [ no J (normal) or [ yes J ( 1nvers1on) mode. Once the mode has been selected, press the ENTER button to setup, then press the MENU button for one second or wait for one minute to exit the menu mode.[tilt) Y-axis rotation settingTo select the [tilt]: press the MENU button to show the ( tilt J on the display, Then press ENTER button to enter. press the DOWN or UP button to select the ( no J(normal) or ( yes J(Reverse rotation) mode. Once the mode has been selected, press the ENTER button to setup, then press the MENU button for one second or wait for one minute to exit the menu mode.[LED] Set whether the LED display Is always onTo select the [LED display is always on or not lit] : press the MENU button to show the [ Led Jonthe display, Then press ENTER button to enter. Press the DOWN or UP button to select the ( on J(LED d1~play 1s always on) or I oFF] (After the device function setting is completed, the LEDdisplay 1s turned off after 2 minutes ) . Once the mode has been selected, press the ENTER button to setup, then press the MENU button for one second or wait for one minute to exit the menu mode.[dlSP) / [dSIP] Normal display / Inverted display settingTo select the [dlSP ]: press the MENU button to show the [ dlSP] on the display, Then press ENTER button to enter. Press the DOWN or UP button to select the (no] (normal display) orI yes I (Inverted display) mode. Once the mode has been selected, press the ENTER button tosetup, then press the MENU button for one second or wait for one minute to exit the menu mode.[ta St] AUTO TESTSelect [teSt]: Press the MENU button to display [teSt] on the display, then press the ENTER button to enter the detection menu , The device starts self-detection. At this time, the display (teSt) ffashes . Press the MENU button for one second to exit the self-test mode.[temp) temperature detection setting
Select (tenp]: Press the MENU button to display [tenp] on the display, then press the ENTER button to enter. The monitoring module begins to detect the light source temperature of the device and turns off the light source. At this point, the display shows that the device temperature value is flashing, then press the MENU button for one second or wait one minute to exit the menu mode and illuminate the light source.[ rest) RESETTo select [rSet]: press the ENTER button to display RESET on the display. Press the ENTER button and all channels of the device will return to their standard position. The display show LedGobo for about 1 second and then return the menu mode.DMX512 control connectionToe OMX512 is widely used for intelligent lighting control with up to 51 2 channels per unit, The specific connections are shown below.Note: All connected lights must be set to the same channel (SCH or 11CH) mode; otherwise, the Dghts will not be synchronized. After c onnecting the lights and console, tum on the power to all devices and the lights will start working and reset. After the device is reset, the display of all devices wiU show the same address code (1 to 512). This means that all connected devices have receivedthe DMX512 console signal, and the OMX512 console can control the mode of operation of the device.
S channel control Mode
I CH HorizOnta l ·
2CH lncllnalaon
3CH~~.,VII. . . .
4 CH
5CH
6CH
Gradai.ur Strobe
Coul· u r
0-,·-“‘ i::ctfon tD·l·nl ··-1·i::::1 1″:,1~ wobe..-r1112Do-245 elro.,.·ff·l22″–250::iu:etrobele0 1raplde
O o–r O. PHda-functione-211e··9:· Coul· ur autoC
7CH Motif]
OCH··”0-1PHda fun cllon 8-191 Coulau r auto vu. … 2.00- 21115 Cont,61· d1.1·o n
9CH vu . . . .]
11 channel control Mode
I CHHorizontale—
2CHFrettin g–horizontal
3CHlnclinalson-·-
4 CHlncllnaison fretting-·-
‘”
‘”
‘ ”
‘”
10 C HSou nd-,_, No !vc,CI I Or,15~199~i:i:dovlo, co-n~So.Jn<l CO\’”lll o!
11 CHReset… …I
5 CH·”-==–·-V,uM.I
6 CH
7 CH
B CH
Gradateur Slrnbe-·- ., 0-7 PH de f u M Uon …..· tr~O. lent · nplde 100–141 ·b”Obe(O. ra p lde·le nl) 150–119·t·00. · 1’1’·11,.,_,., etr00. eff.i22’6-255I etr00.1· pll1·rapl(M ‘ effel
Couleur0 0· ~ :defu nction · ~~~f:ur··· auto0
9 CH Mottf—.I
Master/slave connectionAccord ing to the needs of the site, use the signal cable to connect the lights, as shown below· all lights mu~t be set to the same channel mode (SCH / 11CH); otherwise, the device will not be’ synchronized; after c onnecting the lights, turn on all the lights, the light will Smartly select one of them as the host, the MASTER signal light Is Illuminated, the display of all slave lights is displayed as SL 1 or SL 2 and the (SLAVE) signal light Is Illuminated, at which point all slave lights will work synchronously with the host.
Troubleahootlng
When the followin g Issues occur with you r device, follow the prompts to resolve the Issue:
1. ~onnect the powe r supply, the light does not work : Check wh ether the power sw itch power
: thetc. are In good condition , whether the plug and socket are in good contact and ~heck
e er the device settings and Input voltage are correct.
‘
[xyz-ips snippet=”download-snippet”]