Fisher Price Y9854 User Manual

Fisher Price Y9854 User Manual

Please keep this instruction sheet for future reference, as it contains important information.Requires two AA (LR6) alkaline batteries for operation (not included).Adult assembly is required. Tool required for assembly: Phillips screwdriver (not included).Wipe this toy with a damp cloth. Do not immerse.This product has no consumer serviceable parts.Do not take this toy apart.

Consumer Information

ICES-003

This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Statement (United States Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.

Note: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Assembled Parts

Battery Installation

For longer life, use alkaline batteries.

• Locate the battery compartment on the back of the toy.
• Loosen the screws in the battery compartment door with a Phillips screwdriver and remove the door.
• Insert two AA (LR6) alkaline batteries.
• Replace the battery compartment door and tighten the screws.
• If the toy begins to operate erratically you may need to reset the electronics. Slide the power/volume switch off and then back on.
• When sounds from this toy become faint or stop, it’s time for an adult to change the batteries.
• Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority for recycling advice and facilities.

Battery Safety Information

In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage:

• Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries from the product. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under adult supervision.

Assembly

• Fit the front axles to the front frame.
• Insert two screws into each front axle and tighten.

• First fit a wheel onto each front axle. Then, fit a cap onto each wheel.
• Insert a screw into each cap and tighten.

• Insert and “snap” the handle into the slot in the back frame.Hint: The handle is designed to fit one way. If it does not seem to fit, turn it around and try again.

• Fit the remaining wheels and caps onto the rear frame.
• Insert a screw into each cap and tighten.

• Fit the back panel assembly to the front panel assembly.

• Insert three screws into the handle and tighten.

Lights, Music & Hands-on Fun!

• Slide the power/volume switch to ON with low volume , ON with high volume or OFF.
• Press the lion’s nose for sounds and lights.
• Press the piano keys to play a note.
• Hear more sounds and lights when baby walks!

Fisher Price Y9854 User Manual – Fisher Price Y9854 User Manual –