gofanco G4-0107A 1080p Wireless HDMI Extender 100m User Guide

1080p Wireless HDMIExtender – 100mUser’s Guide

P/N:HDwireless100-LT

G4-0107A

Thank you for purchasing from gofanco. Our products aim to meet all your connectivity needs wherever you go. For optimum performance and safety, please read the instructions carefully and keep this User’s Guide for future reference. If you need more information about our products, please visit www.gofanco.com. For technical support, email us at [email protected]. For drivers or manual download, please go to www.gofanco.com/downloads.

Important Safety Notices

Please read safety instructions carefully before installation and operation.

• Please pay close attention to all warnings and hints for this device
• Do not expose this unit to rain, heavy moisture, or liquid
• Do not put any items into the device or attempt to modify its operation
• Do not repair the device or open the enclosure without professional guidance to avoid electric shocks. Doing so may void your warranty
• Keep the product in a well-ventilated location to avoid damage from overheating
• Shut off power and make sure environment is safe before installation
• Do not plug the HDMI cables and IR cables in/out when the device is in use to avoid cable damage. Make sure they are plugged into the correct ports
• Use the included DC5V power adapters only. Make sure the specification matches if using 3rd-party DC power adapters

Introduction

The 1080p Wireless HDMI Extender – 100m extends HDMI signals wirelessly from a source device to a display device up to 100 meters. It requires no cables between the Transmitter (TX) and Receiver (RX), making the installation easy and clean. Great for homes and offices.

Note: Wireless transmission distance will vary due to the environmental conditions. Thick walls, brick, glass, electronic interference, and wireless signals from other devices will shorten the wireless transmission distance or cause signal loss.

Features

• Transmits HDMI signals wirelessly up to 328 feet (100m) at 1080p. Supports LPCM 2.0-ch 32KHz/44.1KHz/48KHz audio
• Adopts H.265 high performance code technology. HDMI 1.3, HDCP 1.4, and DVI 1.0 compliant
• IR extension allows you to recognize remote commands from a remote location. 20-60KHz IR frequency
• Less than 120ms latency. Not recommended for real-time applications
• No cables required between Transmitter (TX) and Receiver (RX)
• Operates in a 5GHz wireless spectrum
• Dual antenna design maximizes wireless reception with stable data transmission

Package Contents

• 1080p Wireless HDMI Extender – 100m (1 TX and 1 RX)
• IR blaster cable (1pc)
• IR receiver cable (1pc)
• Antenna (4pcs)
• Power adapter (2pcs)
• User guide

Installation Requirements

1. HDMI source device (DVD player, set top box, PC, etc.)
2. HDMI display device (SDTV/Monitor, HDTV/Monitor, projector, etc.)
3. HDMI cables (not included)

Wireless Frequency

The extender scans then selects the least occupied wireless frequency when powered on. Once the frequency is set, it will not change during operation. To avoid interference, power cycle the TX and RX to scan for new 5G frequency.

Channel	Center Frequency (MHz)	Frequency Range (MHz)	Bandwidth (MHz)
36	5180	5170 – 5190	20
40	5200	5190 – 5210	20
44	5220	5210 – 5230	20
48	5240	5230 – 5250	20
149	5745	5735 – 5755	20
153	5765	5755 – 5775	20
157	5785	5775 – 5795	20
161	5805	5795 – 5815	20
165	5825	5815 – 5835	20

Product Layout

       

Figure 1: Transmitter (TX)

1. Power LED	On when the Transmitter is powered on
2. Link LED	Quick flash: The TX and RX are pairingSlow flash: The TX and RX are transmitting dataSolid on: The TX is updating firmwareOff: The TX and RX are not paired or no signal transmission after successful pairing
3. HDMI In	Connects to your HDMI source device
4. Power Jack	Connects to the included power adapter
5. Antenna (x2)	Connects to the included antenna
6. Pairing Button	Quick press: Resets the TX to factory settingsEnter pairing mode: Press and hold down the pairing button on both the TX and RX for 3 seconds to enter pairing mode
7. Micro USB	Firmware update port
8. IR Out	Connects to the included IR blaster cable

          

Figure 2: Receiver (RX)

1. Power LED	On when the Receiver is powered on
2. Link LED	Quick flash: The TX and RX are pairingSlow flash: The TX and RX are transmitting dataSolid on: The TX and RX are paired successfully or the RX is updating firmwareOff: The TX and RX are not paired or no signal transmission after successful pairing
3. HDMI Out	Connects to your HDMI display
4. Power Jack	Connects to the included power adapter
5. Antenna (x2)	Connects to the included antenna
6. Pairing Button	Quick press: Resets the RX to factory settingsEnter pairing mode: Press and hold down the pairing button on both the TX and RX for 3 seconds to enter pairing mode
7. Micro USB	Firmware update port
8. IR In	Connects to the included IR receiver cable

Hardware Installation

1. Power off all devices including your HDMI source and HDMI display.
2. Install the included antennas to the TX and RX.
3. Pair the TX and RX. See Pairing Instructions on page 8.
4. Connect your HDMI source device to the Transmitter’s HDMI Input connector with an HDMI cable (HDMI cable not included).
5. Optional: Connect the IR Blaster Cable to the Transmitter’s IR interface port. Face the eye towards your HDMI source device’s IR window. This connection is needed only if you need to control your HDMI source from the remote location.
6. Connect your HDMI display to the Receiver’s HDMI Output connector with an HDMI cable (HDMI cable not included).
7. Optional: Connect the IR Receiver Cable to the Receiver’s IR interface port. This connection is needed only if you need to control your HDMI source from the remote location.
8. Plug the included power adapters into the Transmitter’s and Receiver’s Power Jacks, then plug both power adapters into reliable power outlets.
9. Power on your HDMI source device and HDMI display. The wireless extender is ready for use.

Note: For optimal signal range, install in a clear environment with few obstacles. Wireless signals from other devices may interfere with transmission. Contact our technical support team if you have specific questions.

Pairing Instructions

1. Power on the TX and RX. Place them in close proximity to each other.
2. Simultaneously press and hold down the pairing button on both TX and RX units for 3 seconds.
3. The Link LED on both units will begin flashing quickly, continue holding down both pairing buttons.
4. Release both pairing buttons when the RX’s Link LED is solid on and the TX’s Link LED remains blinking.
5. The TX are RX are successfully paired.

TX Link LED Status	RX Link LED Status	Description
Flashing Quickly	Flashing Quickly	The TX and RX are pairing
Flashing Quickly	On	The TX and RX are paired successfully
Off	Off	No pairing or no signal transmission after successful pairing
Flashing Slowly	Flashing Slowly	The TX and RX are transmitting data

IR Cables

         

IR RECEIVER             IR BLASTER

IR Blaster

(1) IR Blaster Signal(2) Power(3) NC

IR Receiver

(1) IR Signal(2) Power(3) Grounding

Figure 3: IR Cable Specifications

Application Diagram

The diagram shows the typical devices used with the wireless extender.

Figure 4 Figure 3: Application Diagram: Application Diagram

IR Application

Figure 5: IR Application Diagram

1. Note that when the angle between the IR receiver and the remote control is ± 45 °, the transmission distance is 0-5 meters; when the angle between the IR receiver and the remote control is ± 90 °, the transmission distance is 0-8 meters.

Notice

• Wireless signals transmitted through walls, glass, brick or other solid objects will cause signal loss and decrease the transmission distance
• External wireless signals from microwaves, wireless mice and wireless keyboards will interfere with HDMI signal transmission
• Keep the unit in a well ventilated environment to prevent it from overheating
• DO NOT expose the unit to rain, moisture, or liquids
• DO NOT place anything on the unit
• DO NOT open the housing, doing so will void the warranty and may cause personal injury due to electronic hazard
• DO NOT plug-in or remove the IR extension cables when the unit is powered on

FAQ & Troubleshooting

Q: The Wireless Connection LED is on, but no video output on the remote display:A:

1) Check the HDMI source device is powered on.2) Check the transmitter’s HDMI Signal LED is on.3) Check the HDMI cables for solid connection. Use different HDMI cables if necessary.4) Press the Reset button on both TX and RX.5) Connect the HDMI source device directly to the display to see if there is a signal.

Q: Poor video quality:A:

1) Check the HDMI cables are connected properly. Use different HDMI cables if necessary.2 ) Change the angle of the antenna on the transmitter unit and receiver unit. Generally, the antenna angle should be positioned as far apart as possible.3) Adjust the position of transmitter unit and receiver unit, and make sure they are within the required signal range.4) Press the “Reset” button on the transmitter unit and receiver unit and reconnect.5) Remove other wireless signals and move any obstacles that are blocking the signal line-of-sight.6) Decrease the distance between the transmitter unit and the receiver unit.

Specifications

Item	Description
HDMI Compliance	HDMI 1.3
HDCP Compliance	HDCP 1.4
Video Bandwidth	6.75 Gbps
Resolution	480i, 480p, 720i, 720p, 1080i, , 1920× (max)
Color Space	RGB/YCbCr YUV 4:4:4, YCbCr YUV 4:2:2, YUV 4:2:0
Color Depth	8/10/12-bit ()
HDMI Audio	LPCM 2.0CH32KHz/44.1KHz/48KHz
Power Adapter (x2)	Input: 100-240V AC 50/60HzOutput: 5VDC/1A
Power Consumption	TX: 2.25WRX: 1.8W
Dimensions	TX / RX:76mm (W) x 98mm (D) x 21mm (H)
Weight	TX/RX: 100g each
Operating Temperature	32 to 104F (0 to 40 C)

Disclaimer

The product name and brand name may be registered trademarks of related manufacturers. TM and ® may be omitted on the user’s guide. The pictures on the user’s guide are just for reference, and there may be some slight differences with the actual products.We reserve the right to make changes without prior notice to a product or system described herein to improve reliability, function, or design.

Thank you for choosing gofanco

www.gofanco.com