HALO Bolt ACDC Max Instruction Manual

Table of Contents

OPERATING INSTRUCTIONSPLEASE READ BEFORE OPERATING THIS EQUIPMENT

SAFETY PRECAUTIONS/MOVING AND STORAGE INSTRUCTIONS

DANGER-CAUTION Read and understand all safety information before using this product. Failure to follow these instructions may result in electrical shock, explosion, the fire which may result in serious injuries, death, or property damage.

When used correctly, lithium-ion rechargeable batteries provide a safe and dependable source of portable power. However, if they are misused or abused, this may result in leakage, burns, fire, or explosion, causing personal injury or damage to other devices.
Misusing or incorrectly connecting your HALO BOLT ACDC MAX may cause an electric shock to users and damage equipment.
Do not operate in explosive atmospheres such as in the presence of flammable liquids, gases, or dust.
Remove jump start clamps from vehicle battery after jump starting vehicle.
Keep your HALO BOLT ACDC MAX dry and away from moisture and corrosive materials. The HALO BOLT ACDC MAX should not be used near water or wet areas such as bathtubs, showers, bathrooms, sinks, swimming pools, or basements.
Do not expose your HALO BOLT ACDC MAX to moisture, water, rain, or
Keep your HALO BOLT ACDC MAX away from heat sources, including open flames, radiators, stoves, ovens, and any other devices that produce heat.
The lithium-ion rechargeable battery used in this charging device may present a risk of fire or chemical burn if mistreated. Do not expose to fire or excessive temperature. Do not expose to heat above 212°F (100°C) or incinerate.
In the unlikely event of leakage or explosion use sand or a chemical fire extinguisher. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Your HALO BOLT ACDC MAX may become warm under extended high power operation. Do not cover, wrap, or otherwise restrict the HALO BOLT ACDC MAX during operation.
Do not disassemble your HALO BOLT ACDC MAX. There are no user-serviceable parts inside. Incorrect reassembly may result in shock or fire hazards.
Do not drop or be subject to strong impacts. Do not operate your HALO BOLT ACDC MAX if it has received a sharp blow, or has otherwise been damaged in any way.
Do not puncture, crush or be subject to mechanical shock.
Only charge your HALO BOLT ACDC MAX by the specified method with the specified charging adapter provided with the unit. Use of an attachment not recommended or sold by a power pack manufacturer may result in a risk of fire, electric shock, or injury to persons.
Do not use any non-HALO-branded accessories with the HALO BOLT ACDC MAX. Doing so may cause an electric shock to users and damage equipment.
Do not operate the power pack with a damaged cord or plug, or a damaged output cable.
The HALO BOLT ACDC MAX, along with its accessories, are not toys and should be kept away from children.
To reduce the risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting the power pack.
Make sure the jumper cables are fully plugged into the jump start output before trying to jumpstart your vehicle.
Do not touch red (positive) and black (negative) jumper clamps together at any point.
Do not insert any foreign object into the ports or openings of your HALO BOLT ACDC MAX.
Do not clean your HALO BOLT ACDC MAX with harsh chemicals, soaps or detergents. Just wipe the case with a soft cloth.
When charging the internal battery, work in a well-ventilated area and do not restrict ventilation in any way.
Make sure the HALO BOLT ACDC MAX’s charging ports do not become contaminated with lint or other debris. Use a canned-air type of product periodically to ensure that the port openings are clear.
Batteries should be recycled or disposed of as per state and local guidelines.
Storage: -4°F – 158°F (-20°C – 70°C), Discharge: 14°F -122°F (-10°C – 50°C), Charge: 32°F – 113°F (0°C – 45°C)

INCLUDED ITEMS– HALO BOLT ACDC MAX– Jumper Cables– Wall Charging Adapter– USB-A to USB-C Cable– Carrying Pouch

OPERATING/INSTALLATION INSTRUCTIONS Charging your HALO BOLT ACDC MAX.To charge your HALO BOLT ACDC MAX, use the provided Wall Charging Adapter, and plug the DC jack into the charging put. Next, connect the wall charging adapter into a wall outlet. The HALO BOLT ACDC MAX will automatically begin charging. When the HALO BOLT ACDC MAX is fully charged, all have battery indicator bars will be solid green and the digital screen will indicate 100% charged. (This could take up to 9 hours).

While charging, the digital screen will illustrate the charge percentage of the HALO BOLT ACDC MAX. When fully charged, disconnect the cable.

NOTE:The HALO BOLT ACDC MAX is designed to charge between 32°F-113°F (0-45° C). A “TEMP” indicator will be illustrated on the digital display if the HALO BOLT ACDC MAX is attempted to be charged outside of this temperature range.

JUMP STARTING YOUR VEHICLE WITH THE HALO BOLT ACDC MAX

Plug the jumper cables into the jump start output on the HALO BOLT ACDC MAX.
Attach the jumper cable clamps to the vehicle battery.– Red clamp on positive terminal (+)– Black clamp on negative terminal (-)NOTE:• Once the jumper cable clamps are attached to the vehicle battery, the LCD will display the vehicle battery voltage.• Do not touch red (positive) and black (negative) clamps together at any point.• If the jump start button flashes red, and the “SAFETY CHECK FAIL” indicator is visible on the LCD screen, the jumper cables have been connected incorrectly. If this fiashing red condition occurs, disconnect the jumper cables from the vehicle battery and restart the process from Step 1.
Press the “Jump Start” button and wait for the solid green light.NOTE:A flashing green light indicates safety checks are in progress.
Start your vehicle.NOTE:If your vehicle fails to start after the first attempt, wait 30 seconds and repeat steps 3 and step 4.If your vehicle does not start after three attempts, we recommend you consult a certified mechanic.
Disconnect the jumper cable clamps from the car battery.

NOTE:The jump start function can not be used in conjunction with USB charging or the AC outlet. Please ensure that you have not activated the USB or AC output modes when attempting to jump-start your vehicle.NOTE:The HALO BOLT ACDC MAX is designed to allow a jump start when used within a safe temperature range. A “TEMP” indicator will beillustrated on the digital display if used outside of the temperature operating range.

JUMPSTART TROUBLESHOOTING TIPS

Condition	Potential Cause	Solution
HALO BOLT ACDC MAXThe jump Start button hasbeen pressed but nothinghappens	The USB ON/OFF Button or theAC Outlet ON/OFF Buttonhas been pressed.	The jump start output can not beused in conjunction with the USBoutput or AC Outlet modes.Ensure that both USB and AC Outlet modes are off.
HALO BOLT ACDC MAX displays a red “BATT TOO LOW” message	The HALO BOLT ACDC MAX is notsufficiently charged to jump startthe vehicle.	Recharge the HALO BOLT ACDC MAXverify at least 50% chargedThen try the jumpstart process again.
HALO BOLT ACDC MAX Jump Start button flashes red and a SAFETY CHECK FAIL message is displayed	The jumper cables have not beenproperly connected to thevehicle battery.	Check the jumper cables and ensurethat the red clamp is connected tothe positive terminal (+) and thethe black clamp is connected to thenegative terminal (-).
HALO BOLT ACDC MAX Jump Start button flashes green continuously	The HALO BOLT ACDC MAX is waitingto be connected to a battery or aSAFETY CHECK FAIL has beentriggered.	Check the jumper cables andensure they are properly connectedto the battery. Check and ensurethe vehicle battery voltage isgreater than 2.0V. If the SAFETYCHECK FAIL indicator is triggeredduring the jumpstart process, it isrecommended that you consultwith a certified mechanic.
HALO BOLT ACDC MAX displays a blue or red “TEMP” indicator	The HALO BOLT ACDC MAX hasdetected a low or high temperaturecondition.	Disconnect the HALO BOLT ACDC MAX and allow the unit to acclimate to temperature operating range (14°F-122°F) (-10°C-50°C)
You can not successfully jump-start your vehicle. The HALO BOLT ACDC MAX displays a vehicle battery with a voltage greater than 12.0V	The HALO BOLT ACDC MAX detects that it is connected to a vehicle battery with a normal starting voltage. This could indicate that another vehicle the component is faulty.	It is recommended that you consultwith a certified mechanic.
HALO BOLT ACDC MAX Jump Start and On/Off button flashes red and blue	This could occur when attempting tojumpstart a vehicle while otherelectrical components (i.e. headlights,heater, radio, etc.) are on.	Turn off your headlights and anyother components that may drainyour car battery and try the jumpstart the process again.
The vehicle battery may be faulty.	It is recommended that you consultwith a certified mechanic.

NOTE:If none of these troubleshooting tips work, please consult a certified mechanic for assistance.

CHARGING A LAPTOP (VIA THE AC OUTPUT PORT)

Connect the AC power plug from your laptop (or another electronic device that is rated at 65 watts or less) into the AC output port of the HALO BOLT ACDC MAX charger.NOTE: Any electronic device can be powered by the AC output port as long as it is rated at 65 watts or less. BE SURE TO CHECK THAT YOUR LAPTOP OR OTHER ELECTRONIC DEVICE IS RATED AT 65 WATTS OR LESS.
Press the AC Power ON/OFF Button and wait for a solid green light NOTE: Make sure the AC power plug is fully plugged into the AC output port before pressing the AC Power ON/OFF Button.NOTE: A flashing green light indicates safety checks are in progress.If you see a flashing red light, the device you connected is rated for greater than 65 watts and cannot be powered using the HALO BOLT ACDC MAX charger.The HALO BOLT ACDC MAX charger will automatically power off after 30 minutes of inactivity. While jump-starting your vehicle, you cannot charge your electronic devices using the USB or AC output ports and you cannot charge the HALO BOLT ACDC MAX battery via the AC wall adapter.

LAPTOP CHARGING TROUBLESHOOTING TIPS

Condition	Potential Cause	Solution
HALO BOLT ACDC MAXpower ON/OFF button flashes red	Electronic device is rated at greater than 65 watts	Only electronic devices rated at 65watts or less can be used with theHALO BOLT ACDC MAX charger
The HALO BOLT ACDC MAX battery is not sufficiently charged to power the connected electronic device	Recharge the HALO BOLT ACDC MAX battery
H ALO BOLT ACDC MAX shuts off unexpectedly	The HALO BOLT ACDC MAX battery is not sufficiently charged to power the connected electronic device	Recharge the HALO BOLT ACDC MAX battery
HALO BOLT ACDC MAX displays a blue or red “TEMP”indicator	The HALO BOLT ACDC MAX hasdetected a low or high temperaturecondition.	Disconnect the HALO BCLT ACDC MAX and allow the unit to acclimate to the temperature operating range (14°F-122°F) (-10°C-50°C).

CHARGING AN ELECTRONIC DEVICE USING A 5V/2.4A USB OUTPUT PORT

Connect the USB-C tip of the supplied USB-C cable into the USB-C input of your electronic device and connect the StandardThe USB end of the supplied USB-C cable into either one of the HALO BOLT ACDC MAX USB 5V/2.4A Output ports.NOTE:If your electronic device does not have a USB-C Input, your HALO BOLT ACDC MAX is also compatible with the charging cable provided with your electronic device. To use, plug the standard USB end of the cable into either one of the two 5V/2.4A USB Output ports located on your HALO BOLT ACDC MAX.
Turn on the USB charging by pressing theUSB Power ON/OFF Button on the HALO BOLT ACDC MAX.NOTE:The HALO BOLT ACDC MAX USB charging feature will automatically power off after 30 minutes of inactivity.

HALO SMART CHARGE TECHNOLOGYYour HALO BOLT ACDC MAX contains the HALO SMART CHARGE TECHNOLOGY to achieve higher compatibility for charging standard 5V USB electronic devices. The HALO SMART CHARGE TECHNOLOGY will allow the HALO BOLT ACDC MAX to communicate with your electronic device and provide the fastest and safest charge for that device.COMPATIBILITYStandard 5V USB electronic devices including Mobile phones, Tablets, PSP, NDS, MP3, MP4, MP5, GPS, Cameras, and more.

USING YOUR HALO BOLT ACDC MAX FLOODLIGHTThe floodlight can be turned on and off by simply pressing and releasing the floodlight ON/OFF button. The first press will turn on the floodlight. A second press will turn on the red emergency light. The third press will turn on SOS flashing red light. The floodlight will automatically turn off after 2 hours of inactivity.

NOTE:Do not look directly into the LED floodlight.

SPECIFICATIONS

Battery Pack Energy:	Containing a 55500 mWh internal battery
Jump Start:	12V/600Amps
Input:	14V/0.85A
USB Output:	2x USB 5V/2.4A
Dimensions:	3.82 x 7.17 x 1.6 inches
Weight:	1.66 lbs
Operating Temperature (During Charging)	32°F – 113°F (0°C – 45°C)
Operating Temperature	14°F – 122°F (-10°C – 50°C)

COMPLIANCE WITH FCC REGULATIONThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules, this device must be used withcertified peripherals and shielded cables. All peripherals must be shielded and grounded. Operation with non-certified peripherals ornon-shielded cables may result in interference to radio or reception.

LIMITED WARRANTY

At HALO, we are dedicated to making the best quality products. To back this up, this product is warranted for 90 days. For full details regarding warranty terms, exclusions and limitations, please visit:ZAGG.com/warranty. This warranty does not affect any statutory rights that you may be entitled to. Keep a copy of your purchase receipt as proof of purchase.

FOR TECHNICAL SUPPORT PLEASECONTACT US AT:ZAGG.COM/SUPPORTORCALL US AT: 888-907-6274HALO910 W LEGACY CENTER WAYSTE. 500, MIDVALE, UTAH 84047WWW.ZAGG.COM/HALO

© 2021 ZAGG Inc | www.ZAGG.com/HALOHALO, HALO BOLT and the H trademarks are the property of ZAGG IncAll rights reserved.314-00940-AZAGG Inc | 910 W Legacy Center Way, Ste. 500, Midvale, Utah 84047Made in China.

report this ad

References

[xyz-ips snippet=”download-snippet”]

Posted

2023-01-24

HALO

admin

Tags:

ACDC, Bolt, HALO, Max