HALO Lighted Bluetooth Headphones Documentation

HALO Lighted Bluetooth Headphones

OVERVIEW

1. LED light key(M)
2. Multi-function button (MFB)
3. Volume+
4. Volume-
5. Microphone
6. TF card slot
7. LED light
8. 3.5mm audio port
9. USB Charging Port

BLUETOOTH® OPERATION

1. Please ensure that the Bluetooth function has been turned on in the settings of your Bluetooth enabled device.
2. Turn the headphone on by holding down the MFB for about 2 seconds.The LED indicator light will flash to detect Bluetooth enabled devices near you and will enter pairing mode.
3. “GEMLINE HP” will appear on the Bluetooth device list, select “GEMLINE HP” to establish pairing. If instructed to enter a PIN code, please enter ‘0000’.
4. The LED indicator light will turn blue to indicate successful pairing.
5. When you want to play audio from another Bluetooth device, disconnect the headphone from the original device and follow steps 1-3 to re-pair the headphones with a new Bluetooth enabled device.

BUTTON CONTROL

• Power On/Off: long press the MFB button
• Play/Pause: Short press the MFB button
• PREV: Long press – to select the previous song
• NEXT: Long press + to select the next song
• Volume Up: Short press + button to increase volume
• Volume Down: Short press – button to decrease volume

HANDS-FREE PHONE USE

• Answer incoming call: Short press MFB button
• End call: Short press MFB button once
• Redial last call: Dual press MFB button
• Reject incoming call: Press MFB button for 2 seconds

AUX PLAYBACK OPERATION

1. Turn on the headphone.
2. Connect the headphone to a smartphone, audio device, or laptop with the 3.5mm AUX cable(included)
3. The next/previous song, volume, and play/pause buttons can only be adjusted on the device that is connected through the 3.5mm AUX cable.

SD CARD PLAYING

Insert a SD card, the headphone will play the music on the card automatically.Short press Mode switch can be changed to Bluetooth mode.

CHARGING THE HEADPHONE

1. When the battery is low, please charge via the included USB cable. The charging time is approximately 2 hours and provides up to 5.5 hours of continuous operation. Standby time is approximately 12 hours.
2. The LED indicator light will be red during charging and the blue light will be bright once it is fully charged.

WARNING

1. Do not disassemble, repair, or modify the headphone.
2. Do not place product in or near fire to avoid danger, as it uses a lithium battery.
3. Avoid storage at extreme temperatures, this can shorten the battery life and may affect the headphone.
4. Keep the headphone dry and do not store the headphone in damp areas to avoid damage to the headphone.
5. Avoid dropping the headphone as it may cause damage the product.

KIND REMINDER

1. To prolong the headphone life span and to avoid hearing damage, please do not listen to music under high volume for long periods of time.
2. When an error occurs with the headphone, please turn off the headphone and restart it to troubleshoot.
3. When the headphone power is low, the Bluetooth range may be affected. Please charge the headphone to avoid disruptions during use.

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by The Gem Group is under license. Other trademarks and trade names are those of their respective owners.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:(1) This device may not cause interference.(2) This device must accept any interference, including interference that may cause undesired operation of the device.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmful interference, and(2)this device must accept any interference received, including interference that may cause undesired operation.

SPECIFICATION

Model: 100200-001BBluetooth Specification: Bluetooth® V4.2Profiles Supported: AVRCP.TS.1.6.0/A2DP.TS.1.3.1/HFP.TS.1.7.0/RF.TS.4.2.0/BB.TS.4.2.0Wireless Working Range: 10m (without obstacles)Built-in Battery: 3.7V/300mAhUSB Recharge Voltage: DC 5VOutput Power: 15mWFrequency Response: 20Hz-20KHz

PACKING LIST

• Halo Lighted Bluetooth® Headphone
• USB Charging Cable
• 3.5mm AUX Cable
• Storage Pouch
• User Manual
• Gift Box