hama 00200001 Universal Notebook Power Supply 45WU Instruction Manual
Product overview
Explanation of warning symbols and notes
Risk of electric shockThis symbol indicates a risk of electric shock from touching product parts carrying hazardous voltage.
WarningThis symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
NoteThis symbol is used to indicate additional information or important notes.
Package contents
- Universal notebook power supply unit
- 7 notebook connectors
- Power cord
- These operating instructions
Safety instructions
- Use the product only for the intended purpose.
- Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
- Ensure there is sufficient scope for heat dissipation and ventilation.
- Only use the article under moderate climatic conditions.
- Do not use the product in areas in which electronic products are not permitted.
- Do not use the product in a damp environment and avoid splashing water.
- Do not short-circuit the battery of the opened terminal device. There is a risk of explosion.
- Protect the product from dirt, moisture and overheating and use it in dry environments only.
- Do not drop the product and do not expose it to any major shocks.
- Do not operate the product outside the power limits specified in the technical data.
- Always pull directly on the plug when disconnecting the cable, never on the cable itself.
- Make sure that cables do not pose a tripping hazard or block emergency exits.
- Do not bend or crush the cable.
- As with all electrical products, this device should be kept out of the reach of children.
- Do not modify the device in any way. Doing so voids the warranty.
- Keep the packaging material out of the reach of children due to the risk of suffocation.
- Dispose of packaging material immediately in accordance with the locally applicable regulations
Risk of electric shock
- Do not open the device or continue to operate it if it becomes damaged.
- Do not use the product if the AC adapter, adapter cable or power cable is damaged.
- Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
Start-up and operation
Note – mains voltage 100 – 240VThe power supply unit is suitable for mains voltages of 100 – 240 V and therefore can be used worldwide. Please note that a country-specific adapter may be necessary.
- Ensure that your notebook requires a supply voltage of 15 V/19 V (+/- 1 Volt).
- You can find this information on the original power supply unit or in your terminal device’s operating manual. If necessary, ask the dealer who supplied your terminal device or contact your terminal device manufacturer’s support service.
- Set the voltage selector switch to the voltage required by your terminal device
Warning
- Do not use the universal notebook power supply unit if you are unable to definitively determine your terminal device’s supply voltage.
- Do not change the voltage again during operation of the power supply unit in combination with a terminal device.
- Ensure that the notebook’s total power consumption does not exceed the power supply unit’s rated output of 45W.
- Failure to comply with this may cause damage to the universal notebook power supply unit and the connected terminal device!
Note the instructions in your device’s operating manual. If these do not contain any instructions expressly to the contrary, proceed as follows:
- Use the connector on the original power supply unit to select the appropriate notebook connector.
- Without connecting it to the power supply unit, determine the mechanical compatibility between the notebook connector and the connection socket on the terminal device.
- The connector must slide easily into the socket but should not exhibit too much play.
Warning
- Only operate the product from a socket that has been approved for the device. The socket must be installed close to the product and must be easily accessible.
- Disconnect the product from the power supply using the On/Off switch – if this is not available, unplug the power cord from the socket.
- If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the power strip’s maximum throughput rating.
- Connect the appropriate notebook connector to the power supply unit’s DC connection cable.
- Connect the power cord to the power supply unit and your terminal device.
- Then connect the mains plug to a properly installed socket.
- The terminal device can now be used and switched on / charged
NoteDisconnect the product from the mains after use.
Care and Maintenance
NoteDisconnect the product from the mains before cleaning
- Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
- Ensure that no water is able to enter the product.
Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/ mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.
Technical data
Ambient temperature: 0°–40° C
Specifications in accordance with Regulation (EU) 2019/1782
| Specifications in accordance with Regulation (EU) 2019/1782 | |
| Manufacturer’s name or trade mark, commercial registration number and address | Hama, HRA12159,
Dresdner Str. 9, 86653 Monheim |
| Model identifier | 00200001 |
| Input voltage | 100 – 240 V |
| Input AC frequency | 50 / 60 Hz |
| Output voltage / Output current / Output power | 15.0 V DC/ 3.0 A/ 45.0 W
19.0 V DC/ 2.37 A/ 45.0 W |
| Average active efficiency | 89.6 % |
| Efficiency at low load (10 %) | 83.9 % |
| No-load power consumption | 0.05 W |
References
[xyz-ips snippet=”download-snippet”]