hama TH-140 Thermometer/Hygrometer Instruction Manual

“TH-140”Thermometer/Hygrometer

001863650018636600176913 001769140017691500176916

Operating Instructions

Controls and displays

  1. Display
  2. MODE button
  3. SET button
  4. UP button
  5. DOWN button
  6. Battery compartment cover
  7. Base

Explanation of Warning Symbols and Notes

WarningThis symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.NoteThis symbol is used to indicate additional information or important notes.

Package contents

  • Thermometer/hygrometer
  • 2xLR1130 button cell
  • These operating instructions

Safety Notes

  • The product is intended for private, non-commercial use only.
  • Protect the product from dirt, moisture, and overheating, and only use it in an adry environment.
  • Do not operate the product outside the power limits given in the specifications.
  • Do not use the product in moist environments and avoid splashes.
  • Do not use the product in areas where the use of electronic devices is not permitted.
  • Do not drop the product and do not expose it to any major shocks.
  • Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
  • Keep the packaging material out of the reach of children due to the risk of suffocation.
  • Dispose of packaging material immediately according to locally applicable regulations.
  • Do not modify the product in any way. Doing so voids the warranty.
  • Do not use the product in the immediate vicinity of heaters or other heat sources or in direct sunlight.
  • Do not open the device or continue to operate it if it becomes damaged.
  • Keep this product, like all electrical products, out of the reach of children!
  • Use the item only in moderate climatic conditions.

Warning –Batteries

  • When inserting batteries, note the correct polarity (+ and -marJpe or make.
  • Remove the batteries from products that are not being used for an extended period (unless these are being kept ready for an emergency).
  • Do not short-circuit batteries.
  • Do not charge batteries.
  • Do not throw batteries in a fire.
  • Keep batteries out of the reach of children.
  • Never open, damage, or swallow batteries or allow them to enter the environment. They can contain toxic, environmentally harmful heavy metals.
  • Immediately remove and dispose of dead batteries from the product.
  • Avoid storing, charging, or using the device in extreme temperatures and extremely low atmospheric pressure(for example, at high altitudes).

Warning –Button cells

  • Do not ingest battery, risk of burns due to dangerous substances.
  • This product contains button cells. If swallowed, the button cell can cause severe internal burns within just two hours and lead to death.
  • Keep new and used batteries out of the reach of children.
  • If the battery compartment does not close securely, stop using the product and keep it out of the reach of children.
  • If you think that batteries were swallowed or are in a part of the body, seek medical assistance immediately.

Getting started

Open the battery compartment cover (6), remove the contact breaker and then close the battery compartment cover (6). The thermometer is now ready for use.4.1 Base (7)To stand the product, the base (7) must be pulled out beneath the battery compartment cover (6) and folded over.

Operation

5.1 Setting the date/time/time format

  • After removal of the batteries’ contact breaker, the normal time is displayed in 12-hour format, and melody signals that the product is ready for use. (Normal time mode)
  • Press the UP (4) or DOWN button (5) to switch between the 12 and 24-hour formats.
  • Use the UP button (4) or DOWN button (5) to select the desired format.
  • Then press the SET button (3) to make the following settings:
  • Hours
  • Minutes
  • To select individual values (hours/minutes), press the UP button (4) or the DOWN button (5) and confirm each selection by pressing the SET button (3).
  • Then complete the process using the MODE button (2).
  • To change the set time, you must press the SET button (3) for 2seconds; you can then continue as described above.
  • Pressing the MODE button (2) twice takes you to the date/year/month settings. To enter the values, hold the SET button for approximately 3seconds.
  • To select individual values, press the UP button (4) or the DOWN button (5) and confirm each selection by pressing the SET button (3).
  • To confirm all your settings and return to the start display, you must press the MODE button.

Note –Input

  • Hold the UP button (4) and the DOWN button (5) to select the values faster.
  • A selected item will flash to indicate that it can be set.
  • The day of the week is automatically selected when you set the date manually.
  • The settings will automatically close if the reisnoentry for 20 seconds. The settings that were made up to that point are not saved!

5.2 Setting and using the alarm function

  • In normal time mode, press the MODE button (2) once to set the alarm function.ALM is shown on the display.
  • Press the SET button (3) for approximately 2seconds. The hour’s display begins to flash.
  • Press the UP button (4) or the DOWN button (5) to select the hour for the alarm time and confirm your selection by pressing the SET button (3). The minute’s display begins to flash.
  • Repeat the process to set the minutes for the alarm time. Then confirm the process with the MODE button.
  • Press the MODE button (2) twice to go to the start display.
  • To activate the alarm function, you must press the MODE button (2) once to switch to ALM mode. If you press the UP button (4) once, the bell symbol appears on the display and the alarm is set.
  • If you press the DOWN button (5) during the alarm, the alarm will be interrupted for 4minutes and then go off again. The ( and :)symbol flashes.
  • If no button is pressed, the alarm automatically switches to the snooze function; the alarm will be likewise interrupted for 4minutes and then go off again. The (and :)symbol flashes.
  • Press any button (except the DOWN button) to stop the alarm/snooze function.

Note

  • When the alarm function is activated, the alarm melody sounds daily at the selected time.• To completely deactivate the alarm function, press the MODE button (2) and then press the UP button (4) three times until the symbol is no longer shown on the display.Press the MODE button (2) twice to return to the start display.is no longer shown on the display.

5.3 Maximum and minimum value (MAX/MIN)

  • The base station automatically stores the maximum and minimum indoor temperature and humidity values.
  • Repeatedly press the UP button (4) to switch between the current temperature, maximum temperature(MAX), and minimum temperature(MIN).
  • Press and hold the UP button (4) for approximately 2seconds to reset the stored maximum and minimum values.

5.4 Hourly reminder alarm

  • If you activate the hourly reminder alarm, a signal will sound every hour on the hour.
  • Press the MODE button (2) once to go to alarm mode (ALM).
  • Press the UP button (4) twice to activate the hourly reminder alarm.
  • If you press the UP button (4) a third time, both the alarm you have set (to go off at a particular time) and the hourly reminder alarm will be activated. Press the button a fourth time to deactivate both alarms.appears on the display if the hourly reminder alarm is activated.appears on the display if both the alarm you have set and the hourly reminder alarm are activated.

Note –Weather symbols

  • The product uses visual pictures to show the current weather conditions (sunny/cloudy/rainy).
  • The weather conditions are measured based on temperature and humidity.
  • No symbol is displayed if the humidity shows ‘- -’.
Sunny Humidity ≤ 45%
Cloudy ≤ 56%
Rainy >56%

5.5 Temperature indicator

  • Press the SET button (3) in normal time mode to switch between °C and °F for the temperature display.
  • Temperature measurement starts automatically when the batteries are inserted. In normal time mode, the display shows the current ambient temperature, which is automatically updated every 20 seconds.

Care and Maintenance

  • Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
  • Make sure that water does not get into the product.

Warranty Disclaimer

Hama GmbH &CoKG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product, or failure to observe the operating instructions and/or safety notes.

Recycling Information

Note on environmental protection:After the implementation of the European Directive 2012/19/EU and 2006/66/EU in the national legal system, the following applies:Electric and electronic devices, as well as batteries, must not be disposed of with household waste. Consumers are obliged by law to return electrical and electronic devices as well as batteries at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country.This symbol on the product, the instruction manual, or the package indicates that a product is subject to these regulations. By recycling, reusing the materials, or other forms of utilizing old devices/Batteries, you are making an important contribution toprotecting our environment.

Technical Data

Thermometer/hygrometer with weather indicator
Power supply 3V 2xLR1130 button cells
Measuring range: Temperature -40°C to +50°C
Measuring range: Humidity 20% to 90%

86652 Monheim /GermanyService &Supportwww.hama.com+49 9091 502-0All listed brands are trademarks of the corresponding companies.Errors and omissions excepted, and subject to technical changes.Our general terms of delivery and payment are applied.00186365_66_00176913_16/04.21

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

, , ,