HH ELECTRONICS TNi-W4 Wall Mounted Loudspeaker User Manual

TENSSEN

INSTALL

WALL MOUNTED LOUDSPEAKERSUSER MANUAL

Contents:English ManualSpecifications

Page:2 – 910 – 16

INTRODUCTION

The Tessen wall mount installation speaker range includes 3 models: TNi-W4 (4 inches), TNi-W6 (6.5 inches), and TNi-W8 (8 inches)providing premium audio reproduction with effortless installation. Each of the TNi-W speakers features adjustable power settings, and the ability to connect to 70V/100V or 8 Ohm lines. Vertical or horizontal mounting is possible using the included multi-position steel bracket, ensuring the engineer has everything required when the box is opened on site. WithEuroblock or M4 input and output connectivity, the TNi series delivers versatility for the job at hand and all enclosed in lightweight ABS enclosures.

SAFETY

The cabinets should be installed by properly qualiﬁed persons, in compliance with all local regulations and laws.The position of installation is also bound by laws and regulations so must be taken into account in the initial planning stages.All installation equipment used is subject to regular safety checks which must be strictly adhered to.If any of the hardware shows any signs of wear or damage, it should be replaced immediately.Failure to do so could result in serious injury or death!

INSTALLATION

1: Choose a suitable location for the installation. Fixing is achieved via the four M4 ﬁxing holes (indicated below) on the included mounting bracket.Before proceeding, please consider the following:

The structural integrity of the mounting surface.
The type of ﬁxing used. This is dependent on the structure of the mounting surface.
The position of the mounting bracket, and available clearance for the cabinet.
Rear clearance and the possibility of hidden hazards, such as wiring or pipework.
For added security, the use of a safety harness is advised and may be legally required in your market.

VERTICAL AND HORIZONTAL CLEARANCE

Model	X	Y	Z
TNi-W4	90	210	30
TNi-W6	118	237	30
TNi-W8	140	265	30

Z – A suggested minimum clearance (Dimensions in mm)

The easiest way to install the bracket system is as follows:

Using spanners (indicated) remove the M8 bolt.
Separate the bracket into halves.
Using suitable ﬁxing, attach the wall mounting bracket ﬁrst.
Attached is the other half of the bracket to the loudspeaker using the included bolts.
Re-assemble the two halves of the bracket using the M8 bolt and associated hardware.

VERTICAL MOUNTING

ROTATIONTo set the loudspeaker rotation, loosen the nut at the bottom of the bracket. Set the required rotation and re-tighten the nut afterward.

TILT

To set the loudspeaker tilt, loosen the two nuts indicated below. Set the desired tilt and re-tighten both nuts.

HORIZONTAL MOUNTING

ROTATIONTo set the loudspeaker rotation, loosen the two nuts indicated below. Set the desired rotation and re-tighten both nuts.

TILTTo set the loudspeaker Tilt, loosen the nut indicated below. Set the desired rotation and re-tighten the nut.

CONNECTION

For convenience, the TN Wall mount loudspeaker range is fitted with both Euro-block and M4 screw input/output terminals. The I/O connections are wired in parallel so can be interchanged if required – please see the internal connection diagram below.

KEEP ALL SPEAKERS IN THE SAME POLARITY.DO NOT MIX LOW IMPEDANCE AND LINE SPEAKERS IN THE SAME SYSTEM.

EUROBLOCK CONNECTION

TERMINAL CONNECTION

INTERNAL CONNECTIONS

70V/100V line systems have the added advantage of allowing many speakers to be used in the setup using parallel connections. Ensure the cable used is capable of delivering the working current and the ampliﬁer has sufﬁcient drive capacity to support the number of speakers in the system. In the example below, the coil tap is set to 5 Watts, powered by a 100W /100V line ampliﬁer. Each TNi’s output level within the system can be set independently based on the location and desired output level.

HOW MANY SPEAKERS CAN I CONNECT?

In the example to the right, the speaker tap is set to 5W (position 4) and the output ofthe ampliﬁer is 100W. This would allow for the theoretical maximum connection of up to 20 speakers per channel. Don’t forget to also allow for cable losses.

AMPLIFIER OUTPUTVOLTAGE TAP SETTING

100W = 20 (total number)5W

It is recommended however that systems are designed with 20% to spare capacity, so as not to put too much strain on the ampliﬁer, or to allow for the addition of additional cabinets in the future.

20 x 80% = 16(Recommended number of loudspeakers)

For safety reasons, it is essential that wiring and connections are installed by a professional only. The length of cable and gauge used are important for optimal performance.Power Modes: Depending on the required output level, and the type of ampliﬁer used to power the system, connections and settings will change. These are summarized below:

OPTION 1: 70V LINE SYSTEM

Five options are available for the 70V line system. Positions 1 to 4 offer variable output levels and the 5th will disable the speaker output.

OPTION 2: 100V LINE SYSTEM

As with the 70V line system, ﬁve options are available for the 100V line system. Positions 1 to 4 offer variable output levels and the 5th will disable the speaker output.

If the ampliﬁer doesn’t have a 70V or 100V line output, the TN Low Impedance setting is used. In this mode, the TN cabinet has an input impedance of 8Ω.Depending on the ampliﬁer used, it may be possible to use more than one loudspeaker in this mode. Please check the ampliﬁer speciﬁcation before proceeding.

Once the TN cabinet has been set too low impedance (setting 6 on the rotary selector), DO NOT connect a signal from the 70V/100V line output on the ampliﬁer. Doing this could cause damage to the cabinet, ampliﬁer, or both!

OPTION 3: LOW IMPEDANCE (8Ω)

LOW IMPEDANCE – PARALLEL CONNECTION – The ampliﬁer will see a combined speaker impedance of 4Ω.Is the ampliﬁer capable of driving into a 4Ω load?

LOW IMPEDANCE – SERIES CONNECTION – The ampliﬁer will see a combined speaker impedance of 16Ω.

REMEMBER: An ampliﬁer can drive into an impedance higher than its output impedance, but one with a lower impedance could cause problems.

SPECIFICATIONS: TNi-W4

ModelSystem typeWoofer SizeTweeter Size100V Power Options70V Power OptionsLow Nominal System Impedance 1Power RatingRecommended Amplifier 2Sensitivity 1W/1m 3Max SPL 1mFrequency responseInput / Link ConnectorHorizontal Dispersion AngleVertical Dispersion Angle

TNi-W4Passive, 2-way, Bass Reflex4″1″ Dome Tweeter30W, 15W, 6W, 3W15W, 7.5W, 3W, 1.5W8 Ohm45W AES, 180W Peak80-160W @ 8 Ohms88 dB SPL111 dB SPL80Hz – 20KHz (-10dB)125Hz – 18KHz (-3dB)Euroblock and M4 terminals90°80°

Enclosure

Main Construction MaterialGrilleFinishMounting BracketUnit dimensions (HWD)Unit weightSingle Carton dimensions (HWD)Packed weightEAN CodeMaster Carton Dimensions (HWD)Master Packed weightMaster EAN Code

ABS PlasticBlack, Circular Steel MeshBlack (White finish optional, subject to MOQ)Adjustable Steel Bracket included295 x 145 x 222mm, 11.6″ x 5.7″ x 8.7″2.8Kg, 6.2 lbs430 x 185 x 175mm, 16.9″ x 7.3″ x 6.9″, 0.014m³3.3Kg, 7.3 lbs5060109456974445 x 405 x 385mm, (17.5″ x 15.9″ x 15.2″) (4pcs)14.2Kg, 31.3 lbs5060109456981

In the interest of continuous development, HH reserves the right to amend product specifications without prior notification.

For polar plots, EASE modeling ﬁles, 2D and 3D drawings ﬁles, please check www.hhelectronics.com

AES standard Pink Noise 12dB crest factor 2 hours
Measured in Full space (4π) conditions
Calculated maximum SPL based on rated power handling

TNi-W4

SPECIFICATIONS: TNi-W6

TNi-W6Passive, 2-way, Bass Reflex6.5″1″ Dome Tweeter40W, 20W, 10W, 5W20W, 10W, 5W, 2.5W8 Ohm55W AES, 220W Peak100-200W @ 8 Ohms90 dB SPL113 dB SPL65Hz – 20KHz (-10dB)80Hz – 18KHz (-3dB)Euroblock and M4 terminals90°80°

Enclosure

ABS PlasticBlack, Circular Steel MeshBlack (White finish optional, subject to MOQ)Adjustable Steel Bracket included330 x 196 x 281mm, 13″ x 7.7″ x 11.1″3.5Kg, 7.7 lbs455 x 240 x 240mm, 17.9″ x 9.4″ x 9.4″, 0.026m³4.1Kg, 9 lbs5060109456998470 x 515 x 515mm, (18.5″ x 20.3″ x 20.3″) (4pcs)17.4Kg, 38.4 lbs5060109457001

In the interest of continuous development, HH reserves the right to amend product specifications without prior notification.

For polar plots, EASE modeling ﬁles, 2D and 3D drawings ﬁles, please check www.hhelectronics.com

AES standard Pink Noise 12dB crest factor 2 hours
Measured in Full space (4π) conditions
Calculated maximum SPL based on rated power handling

TNi-W6

SPECIFICATIONS: TNi-W8

TNi-W8Passive, 2-way, Bass Reflex8″1″ Dome Tweeter40W, 20W, 10W, 5W20W, 10W, 5W, 2.5W8 Ohm65W AES, 260W Peak100-200W @ 8 Ohms91 dB SPL115 dB SPL55Hz – 20KHz (-10dB)75Hz – 18KHz (-3dB)Euroblock and M4 terminals90°80°

Enclosure

ABS PlasticBlack, Circular Steel MeshBlack (White finish optional, subject to MOQ)Adjustable Steel Bracket included390 x 240 x 319mm, 15.4″ x 9.4″ x 12.6″4.2Kg, 9.3 lbs515 x 280 x 270mm, 20.3″ x 11″ x 10.6″, 0.039m³5Kg, 11 lbs5060109457018530 x 595 x 575mm, (20.9″ x 23.4″ x 22.6″) (4pcs)21.3Kg, 47 lbs5060109457025

In the interest of continuous development, HH reserves the right to amend product specifications without prior notification.

For polar plots, EASE modeling ﬁles, 2D and 3D drawings ﬁles, please check www.hhelectronics.com