Honeywell Home PROSiXSIRENO Wireless Outdoor Siren
This wireless outdoor alarm device provides audible and visual notifications and is intended for use with Honeywell Home controls that support PROSiX™ series devices.
Enroll
You must enroll the device in the control. Refer to the control’s programming instruction for detailed procedures.Once enrolled, the device cannot be used with another system until it is removed from the current controller. See the controller’s instructions.Consult the Controller’s instructions to program the Siren Services. See the LED and Sounder table for CHIME operation when enabled (default).After enrolling, verify adequate signal strength by conducting a sensor test (see the controller’s instructions) with the device in its intended mounting location. Adjust the device location and orientation as necessary.
- When prompted:
- 20 sec LED Flashes
- LED comes ON 3 seconds confirming enrollment.
Replace Battery
Battery Caution: Risk of fire, explosion and burns. Do not recharged, disassemble, heat above 212°F (100°C) or incinerate. Dispose of used batteries properly. Keep away from children.
NOTES:Do not mix old and new batteries, battery types or manufacturers.Constant exposure to high humidity may reduce battery life.
LEDS
|
= On | |
= Chirp |
 |
= Slow Flash | |
= Burglary Warble 2 |
|
= Rapid Flash | |
= Temporal Pulse 3 |
 |
= Strobe Flash | |
= Temporal Pulse 4 |
R = RedG = GreenW = White
NOTE: Strobe flash = two flashes per second, then OFF for 1 second
|
R / W |
G / W | Sounder | Status |
 |
|
Power Up – Enrollment | |
 |
|
Power Up – Device enrolled | |
 |
System is Disarmed | ||
|
System is Armed | ||
 |
|
Smoke Alarm | |
|
CO Alarm | ||
 |
|
Burglary Alarm | |
|
|
Low Battery | |
 |
Tamper Activated – Device enrolled / Antisabotage |
- Starts chirping after 7 days, continues until the batteries are replaced or die
- Some controls produce a steady tone, see control’s installation instruction
- 3-sec. Steady green LED, then chirps and slowly flashes while the tamper is faulted.
Specifications
| Range | 300’ (91m) nominal indoors |
| RF Frequency | 2.4GHz |
| Batteries | 4 x 1.5V, AA Lithium |
| Tamper | Cover and Wall |
| Input Voltage | 3.3VDC |
| Current | 339 mA, |
| Siren Output Level | 85 dB at 10’ |
| Operating Temperature | -40° – 122°F / -40° – 50°C (Agency Compliance 32° – 120°F / 0° – 49°C) |
| Relative Humidity | 95% max. (Agency Compliance 93% max.) non-condensing |
| Dimensions | 6.1 in. (15.5 cm) Diameter x 1.8 in. (4.7 cm) |
|
R / W |
G / W | Sounder |
Status |
|
Programmed with CHIME enabled: |
|
System Disarmed | |
|
|
System Armed Away | ||
|
|
System Armed Stay or Zone Faulted |
REFER TO THE INSTALLATION
Product must be tested at least once each year
Support
Approval Listings
FCC / IC
Other Standards:RoHS
U.S. Warranty
http://www.security.honeywellhome.com/warranty
| FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTSThe user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User’s Manual. Unauthorized changes or modifications could void the user’s authority to operate the equipment.CLASS B DIGITAL DEVICE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, as defined by FCC Rules Part 15.105. The Class B Digital Device statement can be viewed at: https://customer.resideo.com/en-US/support/residential/codes-and-standards/FCC15105/Pages/default.aspxFCC / IC STATEMENTThis device complies with Part 15 of the FCC Rules, and Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.RF EXPOSURE Warning – The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 in (20 cm) from all persons and must not be co-located or operated in conjunction with any other transmitter except in accordance with FCC and ISED multi-transmitter product procedures. |
| Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive., Melville, NY 11747, Ph: 516-577-2000 |
2 Corporate Center Drive, Suite 100P.O. Box 9040, Melville, NY 11747© 2020 Resideo Technologies, Inc.www.resideo.com
The Honeywell Home Trademark is used under license from Honeywell International Inc.This product is manufactured by Resideo Technologies, Inc. and its affiliates.
report this ad
[xyz-ips snippet=”download-snippet”]