HORIZON HOBBY Bajarey Ford Raptor 1:10 Scale 4WD Instruction Manual

Bajarey Ford Raptor 1:10 Scale 4WD

FORD RAPTOR 1:10 SCALE 4WD

INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’UTILISATION MANUALE DI ISTRUZIONI

Before operating this vehicle, please read all printed materials thoroughly. Horizon Hobby is not responsible for inadvertent errors in this manual.

EN

NOTICEAll instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.MEANING OF SPECIAL LANGUAGEThe following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury. CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury. NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.WARNING AGAINST COUNTERFEIT PRODUCTS Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum technology.

Age Recommendation: Not for children under 14 years. This is not a toy.SAFETY PRECAUTIONS AND WARNINGSAs the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or property of others. This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of control, so it is advisable to always keep a safe distance in all directions around your model as this margin will help avoid collisions or injury.· Never operate your model with low transmitter batteries. · Always operate your model in open spaces away from full-size vehicles, traffic and people. · Never operate the model in the street or in populated areas for any reason. · Carefully follow the directions and warnings for this and any optional support equipment(chargers, rechargeable battery packs, etc.) you use. · Keep all chemicals, small parts and anything electrical out of the reach of children.

· Never lick or place any portion of the model in your mouth as it could cause serious injury or even death.· Exercise caution when using tools and sharp instruments.· Take care during maintenance as some parts may have sharp edges.· Immediately after using your model, do NOT touch equipment such as the motor, electronic speed control and battery, because they generate high temperatures. You may burn yourself seriously touching them.· Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or serious injury.· Always turn on your transmitter before you turn on the receiver in the car. Always turn off the receiver before turning your transmitter off.· Keep the wheels of the model off the ground when checking the operation of the radio equipment.

TABLE OF CONTENTSCONTENTS ………………………………………………………………………………………………….. 2 WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS…………………….3 QUICK START……………………………………………………………………………………………….3 CHARGING THE BATTERY ……………………………………………………………………………..3 INSTALLING THE BATTERY…………………………………………………………………………….4 SPEKTRUM DX2E RADIO SYSTEM…………………………………………………………………4INSTALLING THE TRANSMITTER BATTERIES…………………………………………………..4 SRS6000 AVC TECHNOLOGY RECEIVER ……………………………………………………….4 STABILITY ASSIST RECEIVER…………………………………………………………………………5 DRIVING PRECAUTIONS……………………………………………………………………………….5 POWERING ON THE VEHICLE ………………………………………………………………………..5 BEFORE RUNNING YOUR VEHICLE ………………………………………………………………..5 AVC SENSITIVITY ………………………………………………………………………………………… 5 DISABLING AVC TECHNOLOGY……………………………………………………………………..6 PERFORMING A CONTROL DIRECTION TEST………………………………………………….6 RUN TIME…………………………………………………………………………………………………….6 CHANGING THE TRAVEL ADJUST SETTINGS…………………………………………………..6 DYNAMITE FUZE 130A SENSORLESS BRUSHLESS ESC …………………………………..6 DYNAMITE FUZE 3800KV BRUSHLESS MOTOR………………………………………………8 TROUBLESHOOTING GUIDE ………………………………………………………………………….8 LIMITED WARRANTY ……………………………………………………………………………………9 FCC INFORMATION ………………………………………………………………………………..10 IC INFORMATION …………………………………………………………………………………..10 WARRANTY AND SERVICE CONTACT INFORMATION ……………………………………10 COMPLIANCE INFORMATION FOR THE EUROPEAN UNION…………………………..10 REPLACEMENT PARTS …………………………………………………………………………..35­36 OPTIONAL PARTS……………………………………………………………………………………….36 EXPLODED VIEWS …………………………………………………………………………………37­41

CONTENTSREGISTER YOUR LOSI PRODUCT ONLINERegister your vehicle now and be the first to find out about the latest option parts, product updates and more. Click on the Support tab at www.losi.com and follow the product registration link to stay connected.COMPONENTS· Losi® Ford Raptor Baja Rey® RTR with AVC® technology: 1/10-Scale 4WD Desert Truck · SpektrumTM DX2E 2.4GHz Transmitter (SPM2335) · SpektrumTM 6-Channel DSMR® AVC Surface Receiver (SPMSRS6000) · SpektrumTM 9KG 23T Waterproof Servo (SPMS605) · Dynamite® FuzeTM 130A Sensorless Brushless Waterproof ESC (DYN4955) · Dynamite® FuzeTM 550 Brushless Motor 3800Kv (DYNS1616) · 4 AA batteries (for transmitter)

2

FORD®® RAPTOR BAJA REY®®: 1:10 4WD RTR · INSTRUCTION MANUAL

EN

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions,” including puddles, creeks, wet grass, snow and even rain.While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine. The various electronic components used in the vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, however, most of the mechanical components are water-resistant and should not be submerged.Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is not performed after running in wet conditions. To maximize the long-term performance of your vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions Maintenance” section below must be performed regularly if you choose to run in wet conditions. If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those conditions.CAUTION: Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty.

· Driving in wet conditions can reduce the life of the motor. The additional resistance of operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or any wet conditions that will increase the load on the motor for an extended period of time.WET CONDITIONS MAINTENANCE· Drain any water that has collected in the tires by spinning them at high speed. With the body removed, place the vehicle upside down and pull full throttle for a few short bursts until the water has been removed.CAUTION: Always keep hands, fingers, tools and any loose or hanging objects away from rotating parts when performing the above drying technique.· Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing.· Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission.

GENERAL PRECAUTIONS· Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle.· Not all batteries can be used in wet conditions. Consult the battery manufacturer before use. Caution should be taken when using Li-Po batteries in wet conditions.· Most transmitters are not water-resistant. Consult your transmitter’s manual or the manufacturer before operation.· Never operate your transmitter or vehicle where lightning may be present.· Do not operate your vehicle where it could come in contact with salt water (ocean water or water on salt-covered roads), contaminated or polluted water. Salt water is very conductive and highly corrosive, so use caution.· Even minimal water contact can reduce the life of your motor if it has not been certified as water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle until the water is mostly removed from the motor. Running a wet motor at high speeds may rapidly damage the motor.

NOTICE: Never use a pressure washer to clean your vehicle.· Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners.· Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light oil. Do not spray the motor.· Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.· Increase the frequency of disassembly, inspection and lubrication of the following: – Front and rear axle hub assembly bearings. – All transmission cases, gears and differentials. – Motor–clean with an aerosol motor cleaner and re-oil the bushings with lightweight motor oil.

QUICK STARTPlease read the entire manual to gain a full understanding of the Baja Rey vehicle, fine-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual.2. Charge a battery for the vehicle. Refer to the included charging warnings and instructions for battery charging information.3. Install the AA batteries in the transmitter. Only use alkaline or rechargeable batteries.4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC to initialize. Always power the transmitter ON before the vehicle and power it OFF after the vehicle has been powered OFF.6. Check the steering and throttle control directions. Verify that the servos are moving in the correct direction.7. Drive your vehicle.8. Perform any necessary maintenance.

CHARGING THE BATTERYChoose a battery designed to work with the Dynamite® FuzeTM 130A Sensorless BL Waterproof ESC. We recommend the Dynamite® 7.4 5000mAh 2S 30C LiPo: Hardcase with EC3TM connector (DYN9005EC). Choose a charger designed to charge 2S Li-Po

batteries. We recommend the Dynamite® ProphetTM Sport Li-Po 35W AC Battery Charger (DYNC2005CA). Refer to your battery and charger manuals for usage, safety, and charging information.

FORD®® RAPTOR BAJA REY®®: 1:10 4WD RTR · INSTRUCTION MANUAL

3

ENINSTALLING THE BATTERY

1. Ensure the ESC is powered OFF. 2. Slide the button to the right to release the battery door. 3. Install the fully charged battery in the vehicle. 4. Connect the battery to the ESC. 5. Close the battery door and slide the battery door button to the left to secure it. 6. Power ON the transmitter, then the vehicle.

SPEKTRUMTM DX2E RADIO SYSTEM

7 6 5

8 9 10

11

12

4

3

2

1

4

1. Steering Wheel Controls direction (left/right) of the model

13

2. Throttle Trigger Controls speed and direction (forward/brake/reverse) of the model

3. BIND Button Puts the transmitter into Bind Mode

4. ON/OFF Switch Turns the power ON/OFF for the transmitter

5. TH.REV Reverses function of the speed control when pulled back or pushed forward

6. Indicator Lights

– Solid green light–indicates adequate battery power

– Flashing green light–indicates the battery voltage is critically low. Replace batteries

7. ST. REV Reverses the function of the steering when the wheels is turned left or right

8. ST Trim Adjusts the steering center point

9. TH Trim Adjusts the throttle neutral point

10. TH Limiter Limits throttle output to 50, 70 or 100%.

11. 3-Position Switch Used to control a third channel and is preset at -100%/Neutral/100%

12. ST Rate Adjusts the sensitivity of AVC technology

13. Antenna Transmits the signal to the model

INSTALLING THE TRANSMITTER BATTERIES1. Push in the battery cover a small amount to release the retaining tab, then remove the cover. 2. Install 4 AA batteries, taking care to align the battery polarity to the diagram in thetransmitter’s battery case. 3. Carefully reinstall the battery cover by aligning the tabs with the slots on the transmitter.For more information on the transmitter, go to www.horizonhobby.com and click on the support tab for the Spektrum DX2E to download the instruction manual.CAUTION: Never remove the transmitter batteries while the model is powered ON. Loss of model control, damage, or injury may occur.CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property.CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to national regulations.

SRS6000 AVC TECHNOLOGY RECEIVERAntenna

Bind/Battery Aux 4/DisableAux 3 Aux 2 Aux 1 Throttle Steering

AUX CHANNELSThe Aux channels can operate as additional servo channels, or as a power supply for a personal transponder.If AVC is active, only 4 channels; Steering, Throttle, AUX3 and AUX4 are operational. The remaining Aux channels can be used to power a personal transponder or lights.If AVC is disabled (see DISABLING THE STABILITY ASSIST FUNCTION), all 6 channels including the Aux channels can operate as servo channels.

FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · INSTRUCTION MANUAL

EN

STABILITY ASSIST RECEIVERAVC® ­ ACTIVE VEHICLE CONTROLTMThe Spektrum receiver features Active Vehicle ControlTM (AVC®) technology that responds similar to traction control in full-scale vehicles. In addition to traction control, AVC technology also increases steering stability during high speed driving or while driving over rough terrain. As you increase the AVC sensitivity, the system increases steering stability and traction control, similar to reducing the amount of steering rate in a computer transmitter. Reducing the sensitivity value increases the amount of steering control from the transmitter. The receiver also enables you to quickly turn AVC on or off if you participate in organized racing.IMPORTANT: You must use digital servos with the AVC receiver. Do not use analog servos as they willl reduce the performance of the system and may cause overheating.

CALIBRATING THE RECEIVER1. With the vehicle on a flat, level surface, insert the Bind Plug in the BIND port on the receiver.2. Connect a fully charged battery pack to the ESC. 3. Power on the ESC. The orange LED flashes, indicating the receiver is in bind mode. 4. Center the ST TRIM and TH TRIM dials on the transmitter. 5. Press and hold the BIND button while powering on the transmitter. 6. Release the BIND button when the orange LED slowly flashes. The transmitter and receiverare linked when the orange LED is solid. 7. Pull the transmitter trigger to Full Throttle. 8. Push the transmitter trigger to Full Brake, then return the trigger to center. 9. Turn the transmitter steering wheel to Full Right. 10. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center.The orange LED flashes once. 11. Remove the Bind Plug, then power off the receiver to save the settings. 12. Power off the transmitter.

FORWARD

BRAKE/REVERSE

DRIVING PRECAUTIONS· Maintain sight of the vehicle at all times. · Routinely inspect the vehicle for loose wheel hardware. · Routinely inspect the steering assembly for any loose hardware. Driving the vehicleoff-road can cause fasteners to loosen over time. · Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics. · Stop driving the vehicle when you notice a lack of power. Driving the vehicle whenthe battery is discharged can cause the receiver to power off. If the receiver loses power, you will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is not covered under warranty.CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries discharged to a voltage lower than the lowest approved voltage may become damaged, resulting in loss of performance and potential fire when batteries are charged.· Do not apply forward or reverse throttle if the vehicle is stuck. Applying throttle in this instance can damage the motor or ESC.· After driving the vehicle, allow the electronics to cool before driving the vehicle again.IMPORTANT: Keep wires away from all moving parts.

POWERING ON THE VEHICLE1. Center the ST TRIM and TH TRIM dials on the transmitter. 2. Power on the transmitter. 3. Remove the body from the vehicle. 4. Connect a fully charged battery pack to the ESC. 5. Power on the ESC.IMPORTANT: The vehicle MUST remain on a flat, level surface and motionless for at least 5 seconds.

BEFORE RUNNING YOUR VEHICLE1. Check for free suspension movement. All suspension arms and steering components should move freely. Any binds will cause the vehicle to handle poorly.2. Charge a battery pack. Always charge the battery pack as per the battery and/or charger manufacturers’ instructions.3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim so that the vehicle drives straight with no input to the steering.4. Perform a Control Direction Test.

AVC® SENSITIVITYThe ST RATE dial adjusts the sensitivity, or stability, value in the receiver. If you increase the sensitivity, the AVC® system becomes more sensitive to the vehicle drifting left or right. You would use maximum sensitivity during high speed driving or drag racing, when you want the vehicle to stay in a straight line. As the sensitivity value increases, the amount of steering travel decreases.Turn the ST RATE knob counter-clockwise to reduce the sensitivity.Turn the ST RATE knob clockwise to increase the sensitivity.IMPORTANT: The ST RATE knob will only adjust the sensitivity when the transmitter is bound to a DSMR® receiver. When the transmitter is bound to a DSM®, DSM2® or DSM Marine receiver, the ST RATE knob controls the steering dual rate.

FORD® RRAAPPTTOORR BBAAJJAA RREEYY®®:: 11::1100 44WWDD RRTTRR ·· IINNSSTTRRUUCCTTIIOONN MMAANNUUAALL

5

EN

DISABLING AVC® TECHNOLOGYIf you participate in organized racing, you may be required to turn AVC off. To turn AVC off: 1. Insert a Bind Plug in the BIND port on the receiver. 2. Insert a second Bing Plug in the DISABLE port on the receiver. 3. Connect a fully charged battery pack to the ESC. 4. Power on the ESC. The orange LED flashes, indicating the receiver is in bind mode. 5. Center the ST TRIM and TH TRIM dials on the transmitter. 6. Press and hold the BIND button while powering on the transmitter. 7. Release the BIND button when the orange LED slowly flashes. The transmitter and receiverare linked when the orange LED is solid. 8. Pull the transmitter trigger to Full Throttle. 9. Push the transmitter trigger to Full Brake, then return the trigger to center. 10. Turn the transmitter steering wheel to Full Right. 11. Turn the transmitter steering wheel to Full Left, then return the steering wheel to center.The orange LED flashes once. 12. Remove the Bind Plugs, then power off the receiver to save the settings. The receiver willcontinuously blink to indicate AVC is disabled. 13. Power off the transmitter. IMPORTANT: You must calibrate the receiver each time it is placed in bind mode. To activate AVC, see the steps in “Calibrating the Receiver.”

PERFORMING A CONTROL DIRECTION TESTPerform a control test with the vehicle wheels off the ground. If the wheels rotate after the vehicle is powered ON, adjust the TH TRIM knob until they stop. To make the wheels move forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger. When moving forward, the wheels should maintain a straight line without any steering wheel input. If not, adjust the ST TRIM knob, so the wheels maintain a straight line without having to turn the steering wheel.

RUN TIME

CHANGING THE TRAVEL ADJUST SETTINGS

The largest factor in run time is the capacity of the battery pack. A larger mAh rating increases the amount of run time experienced.The condition of a battery pack is also an important factor in both run time and speed. The battery connectors may become hot during driving. Batteries will lose performance and capacity over time.Driving the vehicle from a stop to full speed repeatedly will damage the batteries and electronics over time. Sudden acceleration will also lead to shorter run times.TO IMPROVE RUN TIMES· Keep your vehicle clean and well maintained.· Allow more airflow to the ESC and motor.· Change the gearing to a lower ratio. A lower ratio decreases the operating temperature of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.· Use a battery pack with a higher mAh rating.· Use the optimum charger to charge battery packs. (Visit your local hobby dealer for more information.)

1. Hold the trigger in the full brake position and turn the steering wheel to Full Right while powering on the transmitter. The LED flashes rapidly, indicating the programming mode is active.2. Throttle End Point: Continue holding full throttle. Turn the TH TRIM knob to adjust the full throttle end point.3. Brake End Point: Hold the trigger in the full brake position. Turn the TH TRIM knob to adjust the full brake end point. Return the trigger to the center position.4. Left Steering End Point: Hold the steering wheel in the full left position. Turn the ST TRIM knob to adjust the left end point.5. Right Steering End Point: Hold the steering wheel in the full right position. Turn the ST TRIM knob to adjust the right end point. Return the steering wheel to the center position.6. Power off the transmitter to save the travel adjust settings. The minimum travel is 75%, and the maximum travel is 150%.IMPORTANT: If the travel is changed on the DX2E, you must rebind and calibrate the receiver.

DYNAMITE® FUZETM 130A SENSORLESS BRUSHLESS ESC

SPECIFICATIONS

Type Constant/Peak Resistance Function Operation Input Voltage BEC Output Overload Protection Dimensions (LxWxH) Weight

Sensorless 130A/760A 0.0004 Ohm Forward/Brake­Forward/Brake Reverse Proportional forward, proportional reverse with braking delay 7.4V­14.8V (The motor in this vehicle will not support 14.8V.) 6V/3A Thermal 53.5mm x 36mm x 36mm 79 g

ESC LED STATUS· No ESC LEDs will glow when there is no throttle input from the transmitter. · The red ESC LED glows when there is any throttle input from the transmitter.

AUDIBLE WARNING TONES1. Input Voltage: The ESC checks the input voltage when it is powered ON. If a voltage problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause (xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that the battery power is not too low for safe operation.2. Radio Connection: The ESC checks radio signal input when it is powered ON. If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause (x–x–x). Power OFF the ESC and ensure the radio system is operating correctly.

For sensorless brushless motors: 1. Connect the ESC terminal A (typically designated by a blue wire) to the motor’s terminalA (red wire on a Dynamite® FuzeTM sensorless motor). This may also be changed in Programming Item 12, Motor Rotation, without changing wire connections.2. Connect the ESC terminal B (typically designated by a yellow wire) to the motor’s terminal B (blue wire on a Dynamite® FuzeTM sensorless motor).3. Connect the ESC terminal C (typically designated by an orange wire) to the motor’s terminal C (black wire on a Dynamite® FuzeTM sensorless motor).NOTICE: Always disconnect the battery from the ESC when you have finished operating your vehicle. The ESC’s switch only controls power to the receiver and servos. The ESC will continue to draw current when connected to the battery, resulting in possible damage to the battery through over discharge.ESC CALIBRATION PROCEDUREEnsure proper ESC function by calibrating the ESC to your transmitter inputs. 1. Power OFF the ESC.2. Ensure your transmitter is powered ON, the throttle is not reversed, the throttle trim is neutral and the throttle travel range is at 100%. Disable any special functions such as ABS, etc.3. Press the SET button while powering ON the ESC. Release the button as soon as the red LED starts to flash.4. Calibrate the throttle points by pressing the SET button once after each step. – Neutral (1 flash)–leave the throttle at rest, untouched – Full throttle (2 flashes)–pull the throttle fully back – Full brake/reverse (3 flashes)–push the throttle fully forward5. The motor will run 3 seconds after the last step is completed.Tip: If the motor turns in the wrong direction, reverse the connection of any 2 outside motor wires. The center wire must remain in the center and cannot be moved to another motor tab.

6

FORD®TERNA-PSTCOBREBRATJRA, ARVECY:®1: :11:0104W4WDDSCRBTRE · INSTRUCTION MANUAL

ESC FUNCTIONS AND MODESThe ESC includes programming options so you can adjust the way your vehicle performs. Refer to the included settings table to adjust the ESC for your driving conditions.ESC PROGRAMMING PROCEDUREProgramming is accomplished using the SET button on the ON/OFF switch or Digital Program Box (DYNS3005). 1. Connect a fully charged battery to the ESC. 2. Power ON the ESC using the ESC switch. 3. Hold the SET button for 1 second until the green LED blinks, then release the SET buttonto enter programming mode.

EN4. Press and release the SET button as needed to get to the desired menu option (the Green LED will blink corresponding to the menu item number). Programming menu items 1 through 9 are accessible using the SET button on the ESC. Programming menu items 10 and above are only accessible using the optional ESC programming card. Programming of menu items 10 and 11 is only possible after firmware updates to the ESC programming card.5. When at the desired menu item, hold the SET button for 3 seconds until the red LED blinks. 6. Press the SET button to move among the settings based on how many times the red LEDblinks (Refer to the table for more information). 7. Save the setting by holding the SET button for 3 seconds. 8. Power OFF the ESC switch and repeat the instructions above to change other settings.Tip: If desired, the ESC programming can be returned to default settings by powering ON the ESC and holding the SET button for 5 seconds.

PROGRAMMABLE ITEMS Basic Items1 Running Mode2 Drag Brake Force3 Low Voltage Cutoff4 Start Mode

PROGRAMMABLE VALUE

1

2

3

Forward w/ brake Forward/Reverse w/ brake Forward/Reverse

0%

5%

10%

non-protection 2.6V/Cell

2.8V/Cell

Level 1

Level 2

Level 3

4

5

20% 3.0V/Cell Level 4

40% 3.2V/Cell Level 5

660% 3.4V/Cell Level 6

Default Settings

7

8

9

80%

100%

Level 7 Level 8 Level 9

PROGRAMMABLE ITEMS Advanced Items5 Max Brake Force 6 Max Reverse Force 7 Initial Brake Force 8 Neutral Range 9 Timing 10 Reserved Item 11 Reserved Item 12 Motor Rotation 13 Li-Po Cells

PROGRAMMABLE VALUE

1

2

25%

50%

25%

50%

= Drag Brake Force 0%

6% (Narrow)

9% (Normal)

0.00º

3.75º

Counterclockwise Clockwise

Auto Calculate

2 Cells

3 75% 75% 20% 12% (Wide) 7.50º

4

5

6

100%

disable

100%

40%

11.25º 15.00º 18.75º

Default Settings

7

8

9

22.50º 26.25º

3 Cells

4 Cells 5 Cells 6 Cells

DESCRIPTIONS1. Running Mode – Forward Only with Brake Intended for competition use, this mode allows only forward and brake controls. – Forward/Reverse with Brake This mode is the basic all-around mode, allowing forward, reverse and brake controls. To engage reverse while moving forward, apply the brake until the vehicle has come to a complete stop, release brake, then apply the brake again. While braking or in reverse, engaging the throttle will result in the vehicle immediately accelerating forward.2. Drag Brake Force Adjusts the amount of brake automatically applied when the throttle is returned to the neutral position. This simulates the engine braking effect of a full-scale vehicle, allowing improved turn-in and your vehicle’s general response to controls.3. Low Voltage Cutoff This function helps to prevent battery over-discharge. The ESC continuously monitors the battery’s voltage. If the voltage falls below the voltage threshold for 2 seconds, the output power shuts off and the red LED flashes twice repeatedly.The cutoff threshold calculation is based on individual Li-Po cell voltage. For Ni-MH batteries, if the voltage battery pack is higher than 9.0V, it will be treated as a 3-cell Li-Po battery pack; if it is lower than 9.0V, it will be treated as a 2-cell Li-Po battery pack. Example: for a 8.0V Ni-MH battery pack used with a 2.6V/cell threshold, it will be treated as a 2-cell Li-Po battery pack and the low-voltage cut-off threshold will be 5.2V (2.6×2=5.2).4. Start Mode (Punch) Sets the initial throttle punch when the car accelerates. Level 1 gives a very soft initial acceleration and level 4 gives a stronger initial acceleration.5. Max Brake Force Adjusts the maximum braking force. A higher value provides stronger braking, but can also cause the wheels to lock, resulting in loss of control of the car.

6. Max Reverse Force This parameter adjusts the maximum power when travelling in reverse.7. Initial Brake Force (minimum brake) Adjusts the minimum amount of braking power when the brakes engage. The default value is equal to the drag brake value. A high value can lock the wheels when the brake is used.8. Neutral Range Adjusts the throttle sensitivity around the neutral point. A higher value results in the throttle having to be moved more for the vehicle to move forward, backward or brake.9. Timing Adjusts the motor drive current timing. More timing gives more performance, but can lower efficiency and cause damage to the motor and/or ESC by overload or overheating.NOTICE: Always ensure the motor timing is set correctly. Failure to set the motor timing correctly can result in damage to the motor and ESC. Refer to the manufacturer instructions for recommended timing settings.The Following Programmable Items require the optional Digital ESC Program Box:10. and 11. Available Items are subject to firmware updates to the ESC and the optional digital program box.12. Motor Rotation Allows you to make this change in the ESC so no wires need to be changed between the ESC and the motor.13. Li-Po Cells Allows the ESC to automatically detect or manually set the number of cells in your Li-Po battery back.

FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · INSTRUCTION MANUAL

7

EN

DYNAMITE® FUZETM 3800KV BRUSHLESS MOTOR

PRECAUTIONS· Never touch moving parts.· Never disassemble while the batteries are installed.· Always let parts cool before touching.GEARINGYour vehicle has been equipped with the optimal gearing for the stock platform. It offers an ideal balance between speed, power and efficiency. Should you decide to customize your vehicle with optional batteries or motors, it may be necessary for you to change the pinion or spur gear.

Installing a pinion gear with fewer teeth or a spur gear with more teeth will provide greater torque but will reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with fewer teeth will reduce torque and increase top speed. Care should be taken when installing larger pinion gears as this can “overgear” the vehicle, resulting in overheating of the motor and ESC. When testing different gearing options, pay close attention to the temperature of the motor and speed control to ensure you are operating within the temperature range of the components. The motor or ESC should never be so hot that it cannot be touched. If temperatures are too hot, a different gearing combination with a lower pinion gear and/or higher spur gear is suggested.

TROUBLESHOOTING GUIDE

PROBLEMVehicle does not operateMotor runs but wheels do not rotateSteering does not work Will not turn one direction Motor does not runESC gets hot Poor run time and/or sluggish accelerationPoor range and/or glitching

POSSIBLE CAUSEBattery not charged or plugged in ESC switch not “On” Transmitter not “On” or low battery Pinion not meshing with spur gear Pinion spinning on motor shaft Transmission gears stripped Drive pin broken Servo plug not in receiver properly Servo gears or motor damaged Servo gears damaged Motor wire solder joint is damaged Motor wire broken ESC damaged Motor over-geared Driveline bound up Battery pack not fully charged Charger not allowing full charge Driveline bound up Transmitter batteries low Vehicle battery low Loose plugs or wires

SOLUTIONCharge battery/plug in Turn on ESC switch Turn on/replace batteries Adjust pinion/spur mesh Tighten pinion gear setscrew on motor shaft flat spot Replace transmission gears Check and replace drive pin Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity Replace or repair servo Replace or repair servo Resolder the motor wire with the proper equipment Repair or replace as needed Contact Horizon Hobby Product Support Use smaller pinion or larger spur gear Check wheels and transmission for binding Recharge battery Try another charger Check wheels, transmission for binding Check and replace Recharge battery Check all wire connections and plugs

8

FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · INSTRUCTION MANUAL

EN

2-YEAR LIMITED WARRANTYWhat this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship for a period of 2 years from the date of purchase.What is Not Covered This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations or (vii) use that violates any applicable laws, rules, or regulations.OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.Purchaser’s Remedy Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.Law These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.WARRANTY SERVICES Questions, Assistance, and Services Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local

distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.Inspection or ServicesIf this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/_servicecenter_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a Li-Po battery, please contact the appropriate Horizon Product Support office.Warranty RequirementsFor Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.Non-Warranty ServiceShould your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www. horizonhobby.com/content/service-center_render-service-center.ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.10/15

FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · INSTRUCTION MANUAL

9

EN

Warranty and Service Contact Information

Country of Purchase

Horizon Hobby

Contact Information

Horizon Service Center (Repairs and Repair Requests)

servicecenter.horizonhobby.com/RequestForm/

United States of America

Horizon Product Support (Product Technical Assistance)

877-504-0233

Sales

800-338-4639

European Union

Horizon Technischer Service Sales: Horizon Hobby GmbH

+49 (0) 4121 2655 100

*For the most up-to-date customer service contact information, please visit: www.horizonhobby.com/content/service-center-render-service-center

Address2904 Research Road Champaign, Illinois 61822 USA*Hanskampring 9 D 22885 Barsbüttel, Germany

FCC STATEMENTFCC ID: BRWDX2EQ2UCFCC ID: BRWDASRX12This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment to an outlet on a circuit different from that to which the receiveris connected. · Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NOTICE: Modifications to this product will void the user’s authority to operate this equipment.IC INFORMATIONIC: 6157A-DX2EQ2UC IC: 6157A-AMRX12 This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

COMPLIANCE INFORMATION FOR THE EUROPEAN UNIONEU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the RED and EMC Directive.A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.

Instructions for disposal of WEEE by users in the European UnionThis product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.

10

FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · INSTRUCTION MANUAL

IT

Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi

Part #DYN4955DYNS1616 LOSA3573 LOSA6250 LOSA6937 LOSA6940 LOSA6956 LOSA6957 LOSB3008 LOS43025 LOS230010LOS230011

EnglishFuze 130A Sensorless Brushless WP ESCFuze 550BL Motor, 3800Kv 1.0 Module Pitch Pinion, 13T Set Screws, 4mm & 5mm (6) 5x10mm Sealed Ball Bearing (2) 6x12mm Sealed Ball Bearing (4) 12x18x4mm Sealed Ball Bearing (2) 10x15x4mm Bearing 3x6x2.5mm Ball Bearing (2) Alpine Wheel and Tire Mounted (2) Roll Cage Sides L&RTop Bar, X-Bar,Cover & Tire Moun

LOS230012LOS230013 LOS230020 LOS230066 LOS230067 LOS230068 LOS230069 LOS231005LOS231006

Fr Bar, RR Body Mnt Bar, Bumper, Tower SupportBody Button Base & Top (22) Interior Set with Helmets, Clear King Shocks Raptor Body Set Black Rhino Raptor Body Set Ford Raptor Body Adaptor Set Rear Red LED Light Bar Rear Bulkhead,Fan Panel, MudguardsBattery Tray,Door, Lock, 2S Spacer

LOS231007 Front Upper Arm/Shock Mount, RR Chassis Brace

LOS231008LOS231010 LOS231011 LOS231012 LOS231013 LOS231058 LOS232001 LOS232002 LOS232003 LOS232004 LOS232005 LOS232006 LOS232007 LOS232008 LOS232009 LOS232010 LOS232012 LOS232013 LOS232014 LOS232051LOS233001LOS233002 LOS233003LOS233004LOS233005LOS234002

Servo Mount, Steering Servo Set PlasticChassis Plate & Motor Cover Plate Center Chassis Brace & Standoffs Motor Mount Steering Hardware Set Front Bumper Set Axle Housing Set; Rear Center Transmission Housing Front Gear Box/Bulkhead HD Diff Housing & Internals: Baja Rey Rear Driveshaft Set: Baja Rey Hex, Rotor, Caliper & Pin Set (4) Center Transmission Gear Set 40T Ring & 14T Pinion Gear FR/RR Front Axle Set (2) Center Drive Shaft Center Outdrive Set Front Outdrive Set Rear Axle Shaft Set Open Rear Diff Gear SetShock Ends, Tops, PistonFR/RR Shock Body & Collar Set FR/RR Shock Shaft Set & HardwareFR/RR Shock Seal & Limiter SetFront and Rear Spring SetShock Tower, Upper/Track Rod Mounts, Rear

LOS234003 Trailing Arm, Steering, Upper, Drag Link St

LOS234004LOS234005 LOS234006 LOS234007 LOS234008 LOS235001 LOS235002 LOS235003 LOS235004 LOS235005

Front Suspension Arm Set Upper/LowerSteering Spindle Set & Hardware Front & Rear Sway Bar Links Front Hinge Pins & Brace Set 7mm Steel Pivot Ball Double Boss (10) Cap Head Screws M2 x 6mm (10) Cap Head Screws M2.5 x 10mm (10) Cap Head Screws M3 x 6mm (10) Cap Head Screws M3 x 25mm (10) Button Head Screws M2.5x6mm (10)

Deutsch Fuze 130A Sensorless Brushless ESC spritzwassergeschützt Fuze 550BL Motor, 3800Kv Ritzel Modul 1, 13T Madenschrauben 4 & 5 mm (je 6) Kugelllager, gekapselt 5 x10mm Kugelllager, gekapselt 6 x12mm (4) Kugelllager gekapselt 12 x18x 4mm Kugellager 5 x 10 x 4mm (2) Kugelllager, 3x6x2.5mm (2) Montiertes Alpin-Rad und Reifen (2) Überrollbügelteile links und rechtsObere Abdeckung, X-AbdeckungKarosserieteil hinten StoßfängerBody Button Base & Top (22) Interiorset mit Helmen, transparent King Shocks Raptor-Karosseriesatz Black Rhino Raptor-Karosseriesatz Ford Raptor Body Karosserie-Adapterset Rote LED-Leuchtbalken, hinten Lüfterpanel, SchmutzfängerAkkuhalter und Klappe, 2S DistanzstückStoßdämpferbefestigung hinten mit ChassishalterServohalterChassisplatte und Motorabdeckung Chassishalter und Distanzstücke Motorhalter Zubehörset Lenkung Stoßstangensatz, Front Achsgehäuseset hinten Achsgehäuse mitte Getriebegehäuse mit Halter Differentialgehäuse mit Einsätzen Antriebswelle hinten Scheibenbremse mit Bremssattel Vorne/Hinten Getriebeset Mitte Stirnrad 40 Zähne & 14 er Ritzel Vorderachsenset (2) Antriebswelle Mitte Antriebsklaue mitte Antriebsklaue vorne Hinterachsewellenset Offenes Heckdifferential GetriebesatzStoßdämpferendteile, KolbenStoßdämpfergehäuse, Distanzringe v/h Dämpfer Kolbenstange mit ZubehörStoßdämpferdichtung und BegrenzerDämpferfedern v/hDämpferbrücke hintenLenkgestängeQuerlenkenkerset untenLenkspindelset: Baja Rey Querlenkerverbinder vorne Qiuerlenkerstifte und Halter 7mm Kugelköpfe (10) Sechskantschraube M2 x 6mm (10) Sechskantschraube M2.5 x 10mm (10) Sechskantschraube M3 x 6mm (10) Sechskantschraube M3 x 25mm (10) Halbrundschraube M2.5 x 6mm (10)

FrançaisContrôleur Fuze Brushless 130A étancheMoteur Fuze Brushless 550, 3800Kv Pignon modulaire 1.0, 13 dents Vis, 4mm et 5mm (6 chacun) Roulements à billes scellés 5x10mm (2) Roulements à billes scellés 6x12mm (4) Roulements à billes scellés 12x18x4mm (2) Roulements 5 x 10 x 4mm (2) Roulements à billes 3x6x2.5mm (2) Support volant et pneu alpin (2) Faces latérales gauche et droite de l’arceau cageBarre supérieure, Barre X, protection et support pneuBarre avant, barre de support de carrosserie arrière, support Anneaux de protection de carrosserie (22) Décoration intérieure avec casques, transparente Ensemble de carrosserie King Shocks Raptor Ensemble de carrosserie Black Rhino Raptor Ensemble d’adaptateur de carrosserie Ford Raptor Barre d’éclairage à DEL arrière rouge Cloison arrière, ventilateur et bavettesSupport batterie, trappe, verrou et cales 2STriangle supérieur/fixation d’amortisseur avant, renfort arrière de châssisSupport servo, servo de direction plastiquePlatine de châssis et couvercle moteur Renfort central de châssis et entretoises Support moteur Set d’accessoires de direction Jeu de pare-chocs avant Carter de pont arrière Boitier de transmission centrale Set de carters de transmission avant/Cellule Corps de différentiel renforcé et éléments internes Tiges de cardans arrière Hexagone, rotor, mâchoires et goupilles Set de pignons de transmission centrale Anneau 40T et Pignon 14T avant/arrière Axe de roues avant (2) Cardan central Set de noix de cardans centraux Set de noix de cardans avant Axe de roues arrière Ensemble d’engrenage différentiel arrière ouvert Chapes d’amortisseurs, bouchons supérieurs et pistons Corps d’amortisseurs avant/arrière avec bague Tiges d’amortisseurs avant/arrière avec visserieJoint d’amortisseurs avant/arrière avec limiteurRessort avant/arrièreSupport d’amortisseurs, tirantsTringlerie de direction supérieureBras de suspension avant supérieur et inférieurSet de fusées et visserie Tringlerie barre anti-roulis avant/arrière Renfort de cellule avant Rotules Double Boss acier 7mm (10) Vis CHC M2 x 6mm (10) Vis CHC M2,5 x 10mm (10) Vis CHC M3 x 6mm (10) Vis CHC M3 x 25mm (10) Vis BHC M2,5 x 6mm (10)

ItalianoESC brushless waterproof Fuze 130 A senza sensori Motore brushless Fuze 550, 3800 Kv Pignone a passo modulare 1.0, 13 denti Grani, 4 mm e 5 mm (6 cad.) Cuscinetto a sfere sigillato 5×10 mm (2) Cuscinetto a sfere sigillato 6×12 mm (4) Cuscinetto a sfere sigillato 12x18x4 mm (2) 10x15x4mm Cuscinetti 5 x 10 x 4mm (2) Cuscinetto a sfere 3x6x2,5 mm (2) Ruota alpina con pneumatico montato (2) Parti laterali roll cage D&S Barra superiore, barra a X, copertura e supporto gomma Barra ant., barra supporto carrozz. post., paraurto, montante torretta Body Button Base & Top (22): Baja Rey Set interni con caschi, trasparente Set carrozzeria King Shocks Raptor Set carrozzeria Black Rhino Raptor Set adattatore carrozzeria Ford Raptor Barra a LED rossa posteriore Paratia post., fan panel, parafango Vano batteria, portello, chiusura, distanziale 2S Braccetto superiore ant. / supporto ammortizz., trapezio post. Supporto servo, set servo sterzo in plastica Piastra telaio & piastra copertura motore Montanti telaio centrali con distanziali Supporto motore Set hardware sterzo Set ammortizzatore anteriore Set alloggiamento asse posteriore Scatola trasmissione centrale Scatola ingranaggio anteriore / paratia Scatola diff. HD ed parti interne Set trasmissione posteriore Set esagone, rotore, spessore e perno Set ingranaggio trasmissione centrale 40T ingranaggio & 14T pignone ant./post. Set asse anteriore Albero di trasmissione centrale Set trascintore centrale Set trascintore anteriore Set semiasse posteriore Set ingranaggio differenziale posteriore apertoTerminali, tappi, pistoni ammortizz.Corpo ammortizz. ant./post & collarino Stelo ammortizz. ant./post e hardware Set guarnizione ammortizz. ant./post. e limitatore Set molle ant./post. Torretta ammortizz., supporti tirante sterzo superiore post. Braccetto longitudinale, sterzo, superiore, tirante sterzo Set braccetti sospensione ant. inferiore/ superiore Set fusello sterzo e hardware: Collegamenti barra antitorsione ant./post. Perni braccetti ant. e set piastrine 7mm Steel Pivot Ball Double Boss (10) Viti a testa piatta M2 x 6mm (10) Viti a testa piatta M2.5 x 10mm (10) Viti a testa piatta M3 x 6mm (10) Viti a testa piatta M3 x 25mm (10) Viti a testa tonda M2.5x6mm (10)

FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · MANUALE DI ISTRUZIONI

35

IT

Replacement Parts // Teileliste // Liste des pièces de rechange // Elenco dei ricambi

Part # LOS235006 LOS235007 LOS235008 LOS235009 LOS235010 LOS235011 LOS235012 LOS235013 LOS235014

English Button Head Screws M2.5x 20mm (10) Button Head Screws M4 x 12mm (10) Flat Head Screws M2.5 x 5mm (10) Flat Head Screws M2.5 x 8mm (10) Flat Head Screws M2.5 x 12mm (10) Set Screw, M3 x 3mm Cup Point (10) Set Screw, M4 x 4mm Cup Point (10) Flat Nut, M3 x 0.5 x 5mm (10) Lock Nut, M2 x 0.4 x4mm (10)

Deutsch Halbrundschraube M2.5 x 20mm (10) Halbrundschraube M4 x 12mm (10) Flachkopfschraube M2.5 x 5mm (10) Flachkopfschraube M2.5 x 8mm (10) Flachkopfschraube M2.5 x 12mm (10) Madenschraube M3 x 3mm spitz (10) Madenschraube, M4 x 4mm spitz (10) Flachmutter M3 x 05 x 5mm (10) Stoppmutter M2 x 0.4mm (10)

Français Vis BHC M2,5 x 20mm (10) Vis BHC M4 x 12mm (10) Vis FHC M2,5 x 5mm (10) Vis FHC M2,5 x 8mm (10) Vis FHC M2,5 x 12mm (10) Vis STHC M3 x 3mm CUV (10) Vis STHC M4 x 4mm CUV (10) Écrou plat M3 x 0,5 x 5mm (10) Écrou auto-freiné M2 x 0,4 x 4mm (10)

LOS235015 Lock Nut, Flanged M5 x 0.8 (10)

Stoppmutter M5 x 0.8mm geriffelt (10)

Écrou auto-freiné épaulé strié M5 x 0,8mm (10)

LOS236002 SPM2335

Differential Shim Kit DX2E 2.4 GHz Transmitter

Differential keil Kit Spektrum DX2E 2.4GHz Fernsteuerung

Kit de cale différentielle Émetteur Spektrum 2,4GHz DX2E

SPMS605

9KG Servo, WP, Metal Gear, 23T

Servo, spritzwassergeschützt 9Kg MG, 23T

Servo 9Kg à pignons métal, étanche, tête 23T

SPMSRS6000 Spektrum SRS6000 DSMR AVC Surface Receiver

TLR5904 TLR5909 TLR5910 TLR5911 TLR5913 TLR5932 TLR5933 TLR5934 TLR5935 TLR5961 TLR5963 TLR5964 TLR5965 TLR6312 TLR6313 TLR6352 TLR74006 TLR255007 VTR236003 VTR236025 VTR246001

Button Head Screws, M3 x 0.5mm x 12mm, Stl, BZ Button Head Screws, M3 x 0.5mm x 16mm, Stl, BZ, Pref Button Head Screws, M3 x 0.5mm x 14mm, Stl, BZ Button Head Screws, M3 x 0.5mm x 20mm, Stl, BZ, Pref Button Head Screws, M2.5 x 0.45mm x 12mm, Stl, BZ Cap Head Screws, M3 x 0.5mm x 10mm, Stl, BZ, Pref Cap Head Screws, M3 x 12mm (10) Cap Head Screws, M3 x 0.5mm x 16mm, Stl, BZ, Pref Cap Head Screws, M3 x 0.5mm x 20mm, Stl, BZ, Pref Screw, M3 x 0.5mm x 8mm, Flat Head, Stl, BZ Screw, M3 x 0.5mm x 12mm, Flat Head, Stl, BZ Screw, M3 x 0.5mm x 16mm, Flat Head, Stl, BZ, Pref Screw, M3 x 0.5mm x 20mm, Flat Head, Stl, BZ, Pref Locknut, M2.5x.45 x 5mm (6) Nut, M3 x 0.5mm x 5.5mm, Nylock, Stl, Clear Zinc Washer, 3.2mm x 7mm x 0.5mm, Stl, Clear Zinc Silicone Shock Oil, 30wt, 2oz. Button Head Screws M4 x .07mm x 12mm (10) Flat Nut, M4 x 0.7 x 7mm (10) M4 Nylock Flanged Nut Screw Pin, Clip Post (10): Glamis Uno

Spektrum SRS6000 DSMR AVC Surface Empfänger TLR Rundkopfschraube, M3 x 12mm (10) TLR Rundkopfschraube, M3 x 16mm (10) TLR Rundkopfschrauben, M3 x 14mm (10 TLR Rundkopfschrauben, M3 x 20mm (10) TLR Rundkopfschrauben, M2.5 x 12mm (10) TLR Zylinderkopfschraube, M3 x 10mm (10) TLR Zylinderkopfschraube, M3 x 12mm (10) TLR Zylinderkopfschraube, M3 x 16mm (10) TLR Zylinderkopfschraube, M3 x 20mm (10) TLR Flachkopfschrauben, M3 x 8mm (10) TLR Flachkopfschrauben, M3 x 12mm (10) TLR Flachkopfschrauben, M3 x 16mm (10) TLR Flachkopfschrauben, M3 x 20mm (10) Stopmutter M2.5 x .45 x 5mm (6) TLR Mutter selbstsichernd, M3 x .5 x 5.5mm (10) TLR U-Scheibe, M3 (10) Silikon Dämpferöl 30wt, 2oz TLR Rundkopfschraube, M4 x 12mm (10) Flachmutter M 4 x 0,7 x 7mm (10) Nylon Bundmutter M4 Stiftschraube (10) GLU

Récepteur SRS6000 avec Technology AVCVis à tête bombée M3 x 12mm (10) Vis à tête bombée M3 x 16mm (10) Vis à tête bombée M3 x 14mm (10) Vis à tête bombée M3 x 20mm (10) Vis à tête bombée M2.5 x 12mm (10) Vis BTR M3 x 10mm (10) Vis BTR M3 x 12mm (10) Vis BTR M3 x 16mm (10) Vis BTR M3 x 20mm (10) Vis à tête fraisée M3 x 8mm (10) Vis à tête fraisée M3 x 12mm (10) Vis à tête fraisée M3 x 16mm (10) Vis à tête fraisée M3 x 20mm (10) Ecrou M2,5×0,45x5mm (6) Ecrou M3 x 0,5 x 5,5mm (10) Rondelles M3 (10) Huile silicone d’amortisseur, 30wt, 60 ml Vis à tête bombée M4 x 12mm (10) Écrou plat, M4 x 0,7 x 7mm (10) Ecrou épaulé autofreiné M4 (10) Supports de clips avec goupilles (10): GLU

Optional Parts // Diverse Teile // Pièces optionnelles // Pezzi opzionali

Part # LOS43006 LOS43011 LOS230009 LOS230026 LOS232011 LOS321009 LOS330001 LOS330005 LOS331001 LOS331002 LOS331003

English Wheels (4) Desert Claws Tires Soft w/Foam (2) Body Set, Clear Sticker Sheet Rear Diff Locker Front Bumper & Skid Plate: Baja Rey LED Roof Light Bar Set Body Set, Clear Aluminum Steering Servo Mount Aluminum Bellcrank Servo Saver Set Adjustable Turnbuckle Set

Deutsch Räder (4) Desert Claws Reifen mit Schaumeinlage (2) Karosserie Set Sticker Bogen Differentialsperre hinten Stoßfänger vorne und Unterfahrschutz LED Light Bar Set f. Dachmontage Karosserie Set Lenkservohalter Alumimium Servo Saver Aluminum Gewindestangenset einstellbar

Français Roues (4) Pneus Desert Claws Soft avec inserts (2) Carrosserie, transparente Feuille d’autocollants Verrou de diff arrière Pare choc avant et protection Rampe lumineuse DEL toit Carrosserie, transparente Support de servo de direction aluminium Sauve servo levier aluminium Biellettes réglables

LOS331004 Aluminum Rear Upper Link & Space Set

Heckanlenkung und Distanzstück Aluminium

Tirant supérieur arrière et entretoise aluminium

LOS331005 LOS331006 LOS331007LOS332001LOS332003 LOS334001LOS334002

Aluminum Servo Arm, 23T Aluminum Servo Arm, 24T Aluminum Servo Arm, 25TAl Lightened Hex Adapter Set, 12mm x 6mmLightened Front Outdrive Set Aluminum Front Spindle SetAL Axle Housing Upper Track Rod Mount

LOS334003 Aluminun Upper Lower Buklhead Track Rod Mounts

Servoarm Aluminium, 23T Servoarm, Aluminium 24T Servoarm Aluminium, 25T Radmitnehmer Set ultraleicht Aluminium 12 x 6mm: Baja Rey Frontabtriebset ultraleicht Radträger Set AluminiumAchsgehäuse oben AluminiumAchsgehäuse Aluminium unten

Palonnier de servo aluminium, 23T Palonnier de servo aluminium, 24T Palonnier de servo aluminium, 25THexagones aluminium allégé, 12mm x 6mmSet de noix de cardans avant allégées Fusées avant aluminium Carter de pont supérieur aluminium Track Rod Mount Cellule supérieure/inférieure aluminium Track Rod Mount

LOS334004 Aluminum Rear Shock Tower Set

Dämpferbrückenset Aluminium hinten

Supports d’amortisseurs arrière aluminium

LOS334005 Aluminum Front Shock Tower

Dämpferbrückenset Aluminium vorne

Supports d’amortisseurs avant aluminium

LOS334006 Aluminum Lower Rear Trailing Arm Set

Spurstangenset unten Aluminium:

Bras arrière inférieur aluminium

ItalianoViti a testa tonda M2.5x 20mm (10) Viti a testa tonda M4 x 12mm (10) Viti a testa piatta M2.5 x 5mm (10) Viti a testa piatta M2.5 x 8mm (10) Viti a testa piatta M2.5 x 12mm (10) Grano, M3 x 3mm punta piana (10) Grano, M4 x 4mm punta piana (10) Dado piatto, M3 x 0.5 x 5mm (10) Dado autobloccante, M2 x 0.4 x4mm (10) Dado autobloccante con flangia dentata M5 x 0.8 (10) Kit di zeppa differenziale Spektrum DX2E trasmittente 2,4 GHz Servo 9 kg, waterproof, ingranaggi metallici, 23 denti Ricevente di superficie Spektrum SRS6000 DSMR AVC Viti testa tonda,M3 x 12mm (10) Viti testa tonda, M3 x 16mm (10) Viti testa tonda, M3 x 14mm (10) Viti testa tonda, M3 x 20mm (10) Viti testa tonda, M2.5 x 12mm (10) Viti testa a brugola, M3 x 10mm (10) Viti testa a brugola, M3 x 12mm (10) Viti testa a brugola, M3 x 16mm (10) Viti testa a brugola, M3 x 20mm (10) Vite a testa piatta, M3 x 8mm (10) Vite a testa piatta, M3 x 12mm (10) Vite a testa piatta, M3 x 16mm (10) Vite a testa piatta, M3 x 20mm (10) Dado autobloccante, M2,5 x 45 x 5 mm (6) Dado autobloccante, M3 x .5 x 5.5mm (10) Rondelle, M3 (10) Olio siliconico ammortizzatori, 30 wt, 2 oz. Viti testa tonda, M4 x 12mm (10) Dado piatto, M4 x 0,7 x 7mm (10) Dado flangiato Nylock M4 Perni viti clip (10): GLUItaliano Ruote (4) Gomme Desert Claws soft con inserti (2) Set carrozzeria, trasparente Adesivi Diff. locker posteriore Paraurto anteriore e piastra proteggi telaio Set barra luci LED tetto Set carrozzeria, trasparente Supporto servo sterzo alluminio Set salvaservo squadrette alluminio Set tiranti filettati regolabili Set collegamenti e distanziali superiori posteriori alluminio Squadretta servo alluminio, 23 denti Squadretta servo alluminio, 24 denti Squadretta servo alluminio, 25 denti Set adattatore esagoni alluminio alleggerito, 12 mm x 6 mm Set trascinatore anteriore alleggerito Set fusello anteriore alluminio Supporto tirante trasversale superiore corpo asse alluminio Supporti tiranti trasversali paratia inferiore superiore alluminio Set torre ammortizzatore posteriore alluminio Torre ammortizzatore anteriore alluminio Set braccio longitudinale posteriore inferiore alluminio

36

FORD® RAPTOR BAJA REY®: F1O:1R0D4®WRDAPRTTORR·BMAJAANRUEAYL®E: D1:I1I0ST4RWUDZIORTNRI

IT

EXPLODED VIEW EXPLOSIONSZEICHNUNG VUE ÉCLATÉE DES PIÈCES VISTA ESPLOSA DELLE PARTILOS230068

VTR236003

LOS230011

LOS43025

LOS231058

LOS235011 LOS234007 LOS234007

TLR5935 LOS235013 TLR6313

TLR5933 TLR5935 LOS231007

LOS234007 TLR5904

LOS234007 LOS235011

LOS234006 LOS231058

LOS235006

TLR5913

LOS235006

TLR5913

TLR5913

LOS230011 TLR255007

LOS230011

LOS230011

VTR236003

TLR5913

TLR5913

LOS230012

LOS230011

LOS230011

LOS230010

TLR5913

LOS235005

TLR5913 LOS230012

TLR5910

TLR5910

LOS230011 TLR5913

LOS230010

LOS235005 TLR5913

LOS235006

LOS230012 TLR5913

LOS235006

TLR5913 TLR5913

TLR5913

TLR5913

FORD® RAPTOR BAJA REY®: 1:10 4WD RTR · MANUALE DI ISTRUZIONI

37

FORD® RAPTOR BAJA REY®:F1O:1R0D4®WRADPRTTORR·BMAJAANRUEAYL®E: 1D:I1I0ST4RWUDZIROTNRI

38

EXPLODED VIEW EXPLOSIONSZEICHNUNG VUE ÉCLATÉE DES PIÈCES VISTA ESPLOSA DELLE PARTILOS230013LOS230066 or LOS230067 or LOS330005

LOS231005LOS230066 or LOS230067 or LOS330005

LOS230020

LOS230069

LOS230020

LOS230066 or LOS230067 or LOS330005

LOS231005

LOS230066 or LOS230067 or LOS330005

LOS43025 LOS235015

IT

EXPLODED VIEW EXPLOSIONSZEICHNUNG VUE ÉCLATÉE DES PIÈCES VISTA ESPLOSA DELLE PARTI

LOS232002

LOS232007

LOS232007 LOSA6250

LOS235003 LOS232002

LOSA6937 LOSA3573

LOSA6937

LOS231012 DYNS1616

TLR6313

LOS232012 LOS232004LOSA6956 LOS232007

LOSA6956 LOS232012

LOS232004

TLR5909TLR5904 TLR6352 DYN4955

ITSPMSRS6000 TLR5904 TLR6352

TLR5910

TLR5904

LOS232003

LOS232013 LOSA6957

LOS236002 10x15x0.2mmLOS232008 LOS232051

LOS236002 5x12x0.4mm

TLR5910

TLR5904

LOS232003

VTR246001

LOSA6937

LOS236002 5x7x0.1mm LOS232008

LOS232012 LOS236002 5x7x0.2mm

SPMS605LOS232010

LOS234008

LOS233001 LOS233004

LOS233001LOS233004 LOS233001 LOS233002

TLR6312 LOS233003

LOS233001 LOS233004LOS233005

LOS233002

LOS233001

LOS233003

LOS236002 5x12x0.4mm

LOSA6957 LOS232013LOS234004

LOS233001

LOS234004

LOS234005

LOS234008

LOS233001

LOS232009 LOS235008TLR5911

LOS234004

LOS234003

TLR5911 LOS234008

LOS234005

LOS235001 LOSA6940 LOS232009LOS232006

LOS234004

LOS234004

LOS235001

LOS234005

VTR246001

LOS232006

LOS232006

LOS234005

FORD®® RAPTOR BAJA REY®®: 1:10 4WD RTR · MANUALE DI ISTRUZIONI

39

ITCHASSIS EXPLODED VIEW CHASSIS EXPLOSIONSZEICHNUNG VUE ÉCLATÉE DU CHÂSSIS VISTA ESPLOSA DEL TELAIO

LOS231008

LOSB3008 VTR236025

LOS231008

LOS231013

LOS231013

LOSB3008 LOS231013

LOS234003

LOSB3008

LOS231008 TLR6313LOS231013

LOS231013LOSB3008 TLR6313

LOS231008 TLR5910

LOS231013

LOS231008

TLR6313

LOS231008

LOS234008 TLR6352

TLR5910 TLR6313

TLR5910 LOS234007

LOS235005

LOS231008

LOS234008

TLR6352

TLR5910

LOS235006LOS230012 TLR5911

TLR5913 LOS231005

LOS234002

LOS235011 LOS235009

TLR6313

TLR5913 LOS231005

LOS235002 LOS234002 TLR5904

TLR5911 LOS235011

LOS235009 LOS231005

TLR6352 LOS231008

TLR5910 TLR6352

TLR5961

LOS231006 TLR5935

LOS234002

LOS234006 LOS234006TLR5909LOS234006

TLR5965

TLR5911

LOS235004

TLR6313

LOS234002

TLR6313

TLR6313 LOS234006

TLR5965

TLR5963 LOS234002

TLR6313 LOS234006

LOS234006

TLR6313 LOS234006LOS234006

LOS231007

TLR6313

TLR5909

LOS230012

LOS234002

TLR6313 TLR5911

LOS235006

TLR5965

TLR5911

LOS235002

LOS231006

TLR5904 LOS235011

TLR5911 LOS234002TLR5965

LOS231011

LOS231011

TLR5961

LOS231011

LOS235009

LOS231010 TLR5963

TLR5963

TLR5935 TLR5961 LOS235009

TLR5963 LOS231006

LOS231010

TLR5963

40

FORD® RAPTOR BAJA REY®:F1O:1R0D4®WRADPRTTORR·BMAJAANRUEAYL®E: 1D:I1I0ST4RWUDZIROTNRI

FORD®® RAPTOR BAJA REY®®: 1:10 4WD RTR · MANUALE DI ISTRUZIONI

REAR EXPLODED VIEW HECK EXPLOSIONSZEICHNUNG VUE ÉCLATÉE ARRIÈRE VISTA ESPLOSA DELLA PARTE POSTERIORE

LOS234008 LOS233001 LOS233002LOS233001

LOS233001 LOS233004LOS233004

LOS233002

LOS232006

TLR6312 LOS233001LOS233003

LOS233005

VTR246001

LOS232006

LOS232014

LOS235001 LOSA6940TLR5964LOSA6940

LOS232001

LOS232014

LOS233003LOS233004 LOS233001

LOS234008 LOS234008LOS232005

LOS232014

TLR5911

LOS234008TLR6313 LOS234003

LOS234003

LOSA6957

TLR5934

LOS232051

LOS236002 5x17x0.4mm

LOS232008 LOS236002 5x7x0.1mm

LOS236002 5x17x0.4mm

LOS236002 5x7x0.2mm LOSA6937

LOSA6937

TLR5934

LOS232001

TLR5911 LOS234008 LOS232001TLR6313

TLR5909 LOS234008TLR5911

TLR5904

LOS232001

LOS236002 10x15x0.2mm

LOSA6957

LOS232014

LOS234003 LOS234008

TLR6313 LOS234008 TLR5911LOS234003

LOS233004 TLR6313

LOS232014

LOSA6940

LOS235001

LOSA6940

LOS232006

LOS232001 TLR5964 LOS232014VTR246001

LOS232006

LOS233001LOS233001 TLR5911LOS234008

LOS234008

41

IT

WWW.LOSI.COM

©2020 Horizon Hobby, LLC.

Losi, Baja Rey, DSM, DSM2, DSMR, AVC, Active Vehicle Control, EC3, Dynamite, Fuze, Prophet and the Horizon Hobby logo are trademarks

or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.®Ford Motor Company Trademarks and Trade Dress are used under license to Horizon Hobby.

US 9,320,977,US 10,528,060. US 9,930,567. US 10,419,970. Other patents pending.

Updated 5/20

57527.1 | LOS03020T1/T2

References

[xyz-ips snippet=”download-snippet”]


Posted

in

by