HollisterInstallation Manual
Model:51159 Noble Bronze51160 Matte SilverFan weight ±2 lbs: 21.4 lbs (9.7 kg)Congratulations on purchasing your new Hunter® ceiling fan!The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.We are here to help!This Instruction Manual is designed to make installation as simple as possible. While working through this Instruction Manual, keep your smartphone or tablet nearby. We have added video links to help you through the more technical sections. If you are unfamiliar or uncomfortable with wiring, contact a qualified electrician. We also provide telephone support at 1.888.830.1326 or visit us at HunterFan.com.READ and SAVE These Instructions
WARNING
Warningw.1 – To reduce the risk of fire, electrical shock, or personal injury, mount the fan directly from the building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.w.2 – To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.w.3 – To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch.w.4 – To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.w.5 – Chemical burn hazard. Keep batteries away from children. This remote contains a lithium button cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.Dispose of cells properly and keep away from children. Even used cells may cause injury.w.6 – Non-rechargeable batteries are not to be recharged. Exhausted batteries are to be removed from the product.Cautionc.1 – All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.c.2 – Use only Hunter replacement parts.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This product conforms to UL Standard 507.
Here are the tools you’ll need to complete your installation:
OPTIONALIf mounting to a support structure, you will also need these tools.
Here is what comes in your box:
We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component.Hunter Pro Tip:Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
Note:Fan style may vary.
Find a part that is missing or damaged?Don’t take it back to the store. Let us make it right. Visit us at HunterFan.com or call us at 1.888.830.1326.
Choosing the Right Installation Location
You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit.Check the room dimensions:
Check the outlet box:
You must be able to secure the fan to the building structure or fan-rated outlet box.
Checking the Ceiling Angle:
Standard Mounting
If you have a flat ceiling:Hang your fan by a standard download. Some fans come with a shorter download for a Low Profile installation.
If you have an angled or vaulted ceiling:
- You will need a longer downrod. (sold separately at HunterFan.com)
- If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit. (Sold separately at HunterFan.com)
Angled Mounting
A little more information on Angled Mounting:For optimum performance and appearance, a longer download should be used with your Hunter ceiling fan when installing on a high or angled ceiling. If your ceiling is angled greater than 34° you will also need an Angled Mounting Kit. Longer down rods and the Angled Mounting Kit are sold separately at HunterFan.com.Hunter Pro Tip:Determining if you need an Angled Mounting Kit:Fold on the dotted line. Place against edge against the wall. Slide towards the ceiling. If the guide touches the wall but not the ceiling, you need an angled mounting kit.
Installing the Ceiling Bracket
Hunter Pro Tip:You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box.Hunter Pro Tip:The machine screws are the ones that came with your outlet box.
Do this first!
WARNING
To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.Option 1:Machine ScrewsUse machine screws (provided with outlet box) and washers when securing to existing ceiling fan-rated outlet box. Make sure it is securely installed and is acceptable for fan support of 31.8 kg / 70 lb or less.
Option 2:Wood ScrewsUse wood screws and washers (included) when securing to support structure with the approved electrical outlet box. Drill 9/64 in pilot holes in a support structure to aid in securing the ceiling bracket with hardware found in the hardware bag.
Installing the Downrod
Follow below if you are using the downrod that came pre-assembled in your box. Need to install a longer or shorter downrod? Check out the guide at the end of this manual.
WARNING
FAN FALL HAZARDTo prevent SERIOUS INJURY or DEATH:
- ALWAYS tighten setscrew with pliers.
- DO NOT hand tighten the setscrew.
- CHECK the setscrew is tight using pliers each time you change fan direction.
Hanging the Fan
NOTICETo prevent damage to the fan, ALWAYS lift holding either the fan housing or the downrod.Place the downrod ball into the slot in the ceiling bracket.Progress Check:Your fan should look like this.
Wiring the Fan
We know the wiring is hard. Let’s make it easier.Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician.You are going to need these:4 Wire Nuts (these are in the bag)
Have a single switch?Follow these steps:Hunter Pro Tip:Here is how to connect the wires:Push the bare metal ends of the wires together and slide a wire nut over them. Then, twist the wire nut clockwise until tight.Give it a gentle pull to make sure none of the wires are loose.
WARNING
The ceiling fan must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
WARNING
All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.Hunter Pro Tip:Have extra wiring?Turn the wires upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. Make sure that the wires are still attached to the wire nuts.
Have dual switches?Follow these steps:
Installing the Canopy
Installing the Blades:
Secure each blade to a blade iron as shown using the blade nuts, found in the hardware bag, and the blade assembly screws, found in the
hardware bag.Repeat x6
IMPORTANTNOTE: If applicable, follow the instructions on the blade. Installing it incorrectly could result in your fan not functioning.
Assembling the Light Fixture
Partially install two light kit assembly screws, found in the hardware bag, halfway into the motor housing as shown. It does not matter which two screw holes you choose.
Feed the wire plugs through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise.
| Insert a third light kit assembly screw, found in the |
Connect the single-pin connectors from the light kit assembly to the connectors from the fan.Connect the white wires together. Connect the blue and black wires together. | Carefully push all switch housing components into the switch housing, then install the switch housing plate using two light kit assembly screws, found in the |
WARNING
FAN FALL HAZARDMake sure all three screws are tight to secure the trim ring to the mounting plate.Note:Fan style may vary.
Installing the Bulbs and Glass
Note:Fan style may vary.WARNING
GLASS FALL HAZARDTo prevent SERIOUS INJURY or DEATH, make sure that glass is properly secured.
Preparing the Remote
The remote control is already paired for use. For your convenience, a remote function card is packed in with your remote.NOTICE
- Always purchase the correct size and grade of battery most suitable for the intended use.
- Replace all batteries of a set at the same time.
- Clean the battery contacts and also those of the device prior to battery installation.
- Ensure the batteries are installed correctly with regard to polarity (+ and -).
- Remove batteries from equipment that is not to be used for an extended period of time.
- Remove used batteries promptly.
Remote Function Guide
|
KeyPress |
Function |
| Light On/Off | |
| Light Dimming | |
| Fan On/Off | |
| Raise Fan Speed | |
| Lower Fan Speed | |
| Fan Reverse | |
| Long Press+ |
Fan Updraft |
| Long Press+ |
Fan Downdraft |
| Long Press |
Dimming Mode On/Off |
| Long Press+ |
Enable Beep |
| Long Press |
Disable Beep |
Installing the Remote Control Cradle
You have two options for installing the remote cradle.Choose which path works best for you.
Troubleshooting
Fan Doesn’t Work
- Make sure the power switch is on.
- Check the circuit breaker to ensure the power is turned on.
- Make sure the blades spin freely.
- Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram.
Excessive Wobbling
- Make sure the blades are properly installed on the blade iron posts.
- Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.
- Use the provided balancing kit and instructions to balance the fan.
Remote Control of Fan is Erratic
- Make sure the battery is installed correctly.
- Install a fresh battery.
Remote Only Works Close to Fan
- Change battery.
Noisy Operation
- Make sure the blades are properly installed.
- Check to see if any of the blades are cracked. If so, replace all of the blades.
Multiple Remote Issues
- If you have multiple remotes or multiple remote-controlled fans installed on the same circuit breaker and you are experiencing interference or faulty operation of your remote controls, please go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote-controlled fans?” for information on how to correct this issue.
Hunter Pro Tip:Cleaning the FanUse soft brushes or cloths to prevent scratching.Cleaning products may damage the finishes.
Limited Lifetime Warranty
Hunter Fan Company grants this limited warranty to the original purchaser of this Hunter ceiling fan. This document can be found at www.HunterFan.com.Thank you for choosing Hunter!How Can Warranty Service Be Obtained?Proof of purchase is required when requesting warranty service. The original purchaser must present a sales receipt or other document that establishes proof of purchase. Hunter, at its sole discretion, may accept a gift receipt. To obtain service, contact Hunter Fan Company online or by phone.www.HunterFan.com/Support/Contact-Us/1-888-830-1326Please do not ship your fan or any fan parts to Hunter. Delivery will be refused.What Does This Warranty Cover?Motor — Limited Lifetime WarrantyIf any part of your ceiling fan motor fails during your ownership of the fan due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide you with a replacement fan free of charge.* The foregoing limited warranty applies only to the motor itself and does not apply to electronic controls — such as remote control transmitters, remote control receivers, or capacitors — used in conjunction with the motor. Such electronic control items are included in the one-year limited warranty below.Other — One-Year Limited WarrantyExcept as otherwise indicated throughout this warranty, if any part of your Hunter ceiling fan fails at any time within one year of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement part free of charge.*Light Kits — Warranty May VaryLight kits are included in the one-year limited warranty. However, you may qualify for additional warranty coverage if your fan includes one of the following:
- LED Light Kits — Three-Year Limited WarrantyIf your LED light kit module (not including glass components) or LED bulb fails at any time within three years of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement part free of charge.*
What Does This Warranty NOT Cover?Labor Excluded. This warranty does not cover any costs or fees associated with the labor (including electrician’s fees) required to install, remove, or replace a fan or any fan parts. There is no warranty for light bulbs (except where otherwise noted); remote control batteries; fans purchased or installed outside the United States; fans owned by someone other than the original purchaser; fans for which proof of purchase has not been established; fans purchased from an unauthorized dealer; ordinary wear and tear; minor cosmetic blemishes; refurbished fans; and fans that are damaged due to any of the following: improper installation, misuse, abuse, improper care, failure to follow Hunter instructions, accidental damage caused by the fan owner or related parties, modifications to the fan, improper or incorrectly performed maintenance or repair, improper voltage supply or power surge, use of improper parts or accessories, failure to provide maintenance to the fan, or acts of God (e.g. flood).ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF ANY KIND WITH RESPECT TO THIS PRODUCT SHALL BE THE REMEDIES SET FORTH HEREIN. HUNTER FAN COMPANY IS NOT RESPONSIBLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THIS PRODUCT ARE LIMITED IN DURATION TO THE PERIOD OF COVERAGE OF THE APPLICABLE LIMITED WARRANTIES SET FORTH ABOVE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.How Does State Law Affect Warranty Coverage?This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
Downrod
If you need a different downrod length follow these steps:
WARNING
FAN FALL HAZARDTo prevent SERIOUS INJURY or DEATH:
- ALWAYS follow the downrod assembly instructions exactly.
- VERIFY the downrod is assembled correctly by firmly pulling on the hanger ball.
- Pin must be reinserted to secure downrod assembly.
© 2020 Hunter Fan Company7130 Goodlett Farms Pkwy, Suite 400Memphis TN 38016PG3958 r102820
[xyz-ips snippet=”download-snippet”]