i-tec Bluetooth Comfort Optical Mouse User Manual

i-tec Bluetooth Comfort Optical
Mouse User Manual

Please read the entire instruction manual carefully. Detailed manual is available on our website www.i-tec.cz/en/ in the tab „Manuals, drivers“. In case of any issues, please contact our technical support at: [email protected]

PACKAGE CONTENTS:

  • Bluetooth Optical Mouse
  • 1x AA 1.5V battery
  • User´s manual

INSTALLATION GUIDE:

Step 1: Installing the battery

  • Whenever new battery is installed, make sure that the battery is undam-aged.
  • Remove the battery cover.
  • Insert one AA battery into the battery compartment, make sure to properly orient the positive and negative ends (+/­) as specified by the marks in the battery compartment. Replace the battery cover and make sure it is locked.
  • Switch on the mouse, LED light will blink.
  • Low-voltage alarming function: when the battery have been used for some time and discover the LED light in „DPI-adjusting button“ blinks automatically, which reminds you that battery´s voltage is becoming low, suggested you replace the battery with new one.

Step 2: Connecting the Bluetooth mouseBefore you install the Bluetooth mouse, please make sure that your computer supports Bluetooth function, and finishes the Bluetooth software installation. Press the Link button for 2 seconds, the LED light in „DPI-adjusting button“ will blink, it´s now searching the Bluetooth device. Then please follow the be-low procedures to install the mouse (It can slightly differs according to the Bluetooht software):

  • Make sure that the Bluetooth function has been activated. Double click the Bluetooth Icon on the Task Bar or in the Control Panel, click „Add a Bluetooth device“.
  • Select „My device is set up and ready to be found“, click „Next“.
  • Select Bluetooth mouse, click „Next“.
  • In case the mouse requires pairing PIN code, enter „0000“.

Note: If you use other Bluetooth software, the installing procedure may be similar. You need to try and understand it by yourself.

DESCRIPTION OF KEYS AND DPI ADJUSTMENT:

  • Using „DPI-adjusting button“, the resolution of mouse can be switched among 1000 / 1600 DPI in turn.
  • Backward and Frontward buttons for your easily navigating forward and backward on the internet.

FUNCTION OF THE BUTTONS IN THE ANDROID OS:

  • Left button: The left button has the same function as control by a finger. Holding down the button for approximately 1s will call special functions (on the homepage).
  • Right button: The right button functions as the back button.
  • Scrolling wheel: Using the wheel you can move between the screens.
  • Scrolling wheel (when pushed down): the same function as the „HOME“ button.
  • Frontward button: No function allocated.
  • Backward button: The backward button functions as the back button.
  • DPI-adjusting button: This button switches the optic sensor sensitivity in three steps 1000 / 1600 DPI.

SYSTEM REQUIREMENTS:

  • MS Windows Vista/7/8/8.1/10 32/64 bit, macOS X, Android
  • Computer with Bluetooth Dongle ore built-in Bluetooth. Bluetooth Dongle is not included in this product.

Notice: Do not use the mouse on the reflective surface, such as glass or mirror. Please avoid using the mouse under the following conditions:

  • Direct sunlight
  • Extreme hot, cold, dusty or magnetic environment
  • Near by fax machine, television, radio, mobile phone or any wireless device
  • Please do not repair unfunctional mouse yourselves, you should find authorized technical support.

FREQUENTLY ASKED QUESTIONS

Available on our website www.i-tec.cz/en/ on the “FAQ” tab of this product.

EUROPEAN UNION ONLY

NOTE: MARKING IS IN COMPLIANCE WITH EU WEEE DIRECTIVE

This equipment is marked with the above recycling symbol. It means that at the end of the life of the equipment you must dispose of it separately at an appropriate collection point and not place it in the normal domestic unsorted waste stream. This will benefit the environment for all. (European Union only).

Determination

Product is determined for using in PC as equipment.

Meets the essential requirements according to:Directive 1999/5/EC, LVD 2006/95/EEC, EMC Directive 2004/108/EEC, 91/31/EEC:

EMI (For Radio parameters):EN 300 328-1 V1.8.1(2012-06); EN 301 489-1 V1.9.2(2011-09); EN 301 489-17V2.2.1(2012-09)

For Electrical Safety:EN 62479(2010); EN 60950-1:2006+A11:2009+A1:2010+A12:2011and it is safety under conditions of standard application.

FCC COMPLIANCE STATEMENTThis equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation

http://www.i-tec.cz/en

References

[xyz-ips snippet=”download-snippet”]

Posted

in

by

admin

Tags:

,