ibiza 2-In-1 Warm White Blinder Matrix Animation Bar User Manual

ibiza 2-In-1 Warm White Blinder
Matrix Animation Bar User Manual

UNPACKING INSTRUCTIONS

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present and have been received in good condition. Notify the freight company immediately and retain packing material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of mishandling. Keep the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.

CONTENTS OF THE CARTON

1 pc. FXBAR140
1 pc. user manual
1 pc. power cable

EXPLANATION OF SYMBOLS ON THE SILKSCREEN

Please read this manual carefully before operating this product.

SAFETY RECOMMENDATIONS

Please read these instructions carefully, they include important information about the installation, usage and maintenance of this product.
Please keep this User Guide for future reference. If you sell the unit to another user, be sure that he also receives this instruction booklet.
Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is not higher than that stated on the bottom of the fixture.
The appliance is part of class I and must exclusively connected to an earthed mains outlet.
This product is intended for indoor use only!
To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable materials close to the unit during operation.
The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are blocked.
The minimum distance luminaire from that part of the luminaire or lamp to the lighted object is 0.5m. 0.5m
·Maximum ambient temperature (Ta) is 104° F (40°C). Do not operate the fixture at temperatures higher than this.
In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type of spare parts.
Make sure the power cord is never crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Avoid direct eye exposure to the light source while it is on as sensitive persons may suffer an epileptic shock (especially meant for epileptics)!.
The product is for decorative purposes only and not suitable as a household room illumination.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
The light source of this luminaire is not replaceable. When it reaches the end of its life time, the whole unit must be discarded..

DISCONNECT DEVICE

Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

FUSE REPLACEMENT

Locate and remove the unit’s power cord. Once the cord has been removed located the fuse holder located inside the power socket. Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one.

Warning: If after replacing the fuse you continue to blow fuses, STOP using the unit. Contact customer support for further instructions. Continuing to use the unit may cause serious damage.

INSTALLATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Never stand directly below the device when mounting, removing or servicing the fixture.

FIXTURE LINKING

You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all fixtures on a serial data link determines the number of fixtures that the data link can support.

Important: Fixtures on a serial/data link must be daisy chained in one single line. Maximum recommended serial data link distance: 100 meters (1640 ft.) Maximum recommended number of fixtures on a serial data link: 16 fixtures

DATA CABLING

To link fixtures together you must use data cables. If you choose to create your own cable, please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.

CABLE CONNECTORS

Cabling must have a male XLR connector on one end and a female XLR connector on the other end.

DMX connector configurationTermination reduces signal errors. To avoid signal transmission problems and interference, it is always advisable to connect a DMX signal terminator.

CAUTIONDo not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm meter to check correct polarity and to make sure the pins are not grounded or shorted to the shield or each other.

LED DISPLAY

The LED display has 4 buttons: MENU / UP / DOWN / ENTER

SYSTEM MENU

Press any key to enter the initial interface.

ADDR – DMX Address Setting

Press the either the MENU, UP, or DOWN buttons until “Addr” is displayed, press ENTER.
The current address will now be displayed and flashing. Press the UP or DOWN buttons to find your desired address. Press ENTER to set your desired DMX address.

CHND – DMX channel Mode

Press the MENU button until “Chnd” is displayed, press ENTER. “6CH”, “8CH”,”12CH”, “60CH” will be displayed
Press the UP or DOWN buttons to find your desired DMX channel mode and press ENTER to confirm and exit.

SLND – Master-Slave Mode

Press the MENU button until “SLnd” is displayed, press ENTER. Select among Mast, SL1 and SL2 and press ENTER.

SoUn – Sound controlled Mode

Press the MENU button until “SoUn” is displayed, press ENTER.
Su 0-59 or Se 00-99 will be displayed. Press the UP or DOWN buttons to find your desired show. Su 0-59 means sound controlled mode with programs from 0 to 59. Select a program and press ENTER. Se 00-99 means Sound sensitivity. 99 is the highest sensitivity.

AUTO – Auto Running effect

Press the MENU button until “Auto” is displayed, press ENTER.
The Display will show “Au 0” – “Au 59”. Press the UP or DOWN buttons to find your desired show, and then press Enter. SP 1-9 will be displayed. Set the auto running speed to a value between 1 and 9 and press ENTER.

COLO – Color selection

Press the MENU button until “Colo” is displayed, press ENTER.
Co 1-15 will be displayed. Select a color between 1 and 15 via the UP & DOWN buttons and press ENTER.

MANU – Manual mode

Press the MENU button until “Manu” is displayed, press ENTER.
Select a color among Red 0-255/Green 0-255/Blue 0-255/Whit 0-255 and press ENTER.

DISP – Display reverse by 180°

Press the MENU button until “dISP” is displayed, press ENTER.
Press the UP button to select “dSIP” to reverse the display, or “dISP” to change the display back.
Press ENTER to confirm.Ver – Displays the device version

DMX CHANNEL CHART PLEASE REFER TO THE END OF THE MANUAL

CAREBefore cleaning the unit, disconnect it if from the mains. Do not use aggressive cleaning agents. Use a clean cloth to wipe any dust or dirt from the product. We are not liable for damage arising from incorrect handing, improper use or wear and tear. We reserve the right to make technical modifications.

SPECIFICATIONS

TROUBLE-SHOOTING

Correct Disposal of this product

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.