IKEA SMAKOKA User Manual

Safety Information

Your safety and the safety of others are very important. This manual and the appliance itself provide important safety messages, to be read and observed at all times.

This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others.All safety messages will follow the safety alert symbol and either the terms:

DANGER Indicates a hazardous situation which, if not avoided, will cause serious injury.

WARNING Indicates a hazardous situation which, if not avoided, could cause serious injury.

All Safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

The appliance must be disconnected from the power supply before carrying out any installation work.

Installation and maintenance must be carried out by a qualified technician, in compliance with the manufacturer’s instructions and local safety regulations to the relevant gas standard. Only use original spare parts. Do not repair or replace any part of the appliance unless specifically stated in the user manual.

WARNING If the information in this manual is not followed exactly, a fire or explosion may result causing property damage or injury.-

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance.
What to do if you smell gas:
Do not try to light any appliance.
Do not touch any electrical switch.
Do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or the gas supplier or authorized person.
Use appliance in well ventilated rooms only.
The electrical and gas connections must comply with local regulations.
When the hob is installed, provide a multi-pole circuit breaker with a contact separation of at least 3 mm, that provides full disconnection.
Regulations require that the appliance is grounded.
The power cable must be long enough for connecting the appliance, once fitted in its housing, to the power supply
Use only rigid metal hose for gas connection.
If necessary, the electrical power cable must be replaced exclusively with a power cable having identical characteristics to the original supplied by manufacturer (type H05V2V2-F 90°C or H05RR-F). This operation must be performed by a qualified electrician.
The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from failure to comply with these requirements.- – Do not use multiple plugadapters or extension cords.
Do not pull the power cable to disconnect it from the electrical supply.
The electrical components must not be accessible to the user after installation.
Do not touch the appliance with any wet part of the body and do not operate it when barefoot.
This hob (class 3) is designed solely for private household use for cooking food.DO NOT USE THIS APPLIANCE AS A SPACE HEATER TO HEAT OR WARM THE ROOM.
Doing so may result in carbon monoxide poisoning and overheating of the hob
The Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls.
The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. They shall not play with the appliance.
The use of a gas appliance produces heat and humidity in the room. Make sure the room is well-ventilated, or install an extractor hood with exhaust duct.
Domestic animals should be kept away from the appliance.
In case of prolonged use, additional ventilation may be necessary (by opening a window or increasing the hood extraction speed).
After use, make sure the knobs are in off position and close the main gas supply cock or the gas cylinder valve.
Overheated oils and fats catch fire easily. Always remain vigilant when cooking foods rich in fat, oil or alcohol (e.g. rum, cognac, wine).- – Unattended cooking on a hob with fat or oil can be dangerous and may result in fire. NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.Danger of fire: do not store items on the cooking surfaces.
Keep the packaging materials out of the reach of children
Before cleaning or maintenance wait for hob to cool down.

WARNING WHEN USING WITH LPG: WHERE THIS APPLIANCES IS INSTALLED IN A MARINE CRAFT OR IN CARAVANS, IT SHALL NOT BE USED AS A SPACE HEATER.

WARNING DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE

WARNING DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION

WARNING DO NOT MODIFY THIS APPLIANCE

Product description

Removable pan stand grids
Semi rapid burner
Semi rapid burner
Rapid burner
Auxiliary burner
Rapid control knob
Semirapid burner control knob
Semirapid burner control knob
Auxiliary burner control knob

Symbols
Solid disc	Tap closed
Large flame	Maximum
and star	opening/delivery and electric
ignition
Small flame	Minimum opening or reduced delivery

Daily use

Do not let the burner flame extend beyond the edge of the pan.

Important: when the hob is in use, the entire hob area may become hot.

To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting.
Press the knob against the control panel to ignite the burner
After the burner has ignited, keep the knob pressed for about 5-10 seconds to allow proper device operation.
This burner safety device shuts off the gas supply to the burner if the flame goes out accidentally (because of sudden draught, an interruption in the gas delivery, boiling over of liquids, etc.).
The knob must not be pressed for more than 15 sec. If, after that time has elapsed, the burner does not remain lit, wait at least one minute before trying to light it again.

NOTE: should particular local conditions of the delivered gas make the ignition of burner difficult, it is advisable to repeat the operation with the knob turned to small flame setting.

The burner might go out when the knob is released. This means that the safety device has not warmed up enough. In this case, repeat the operations described above.

Helpful hints and tips

This hob has burners of different diameters. For better burner performance, please stick to the following rules:

Use pots and pans with bottoms the same width as that of the burners or slightly larger (see following table).
Only use flat-bottomed pots and pans.
Use the correct amount of water for cooking foods and keep the pot covered.
Make sure pots on the grates do not protrude beyond the edge of the hob.IMPORTANT: improper use of the grids can result in damage to the hob: do not position the grids upside down or slide them acrossthe hob.Do not use:
Cast iron griddles, ollar stones, terracotta pots and pans.
Heat diffusers such as metal mesh, or any other types.
Two burners simultaneously for one receptacle (e.g. fish kettle).

Burner	Pot Ø
Rapid	from 24 to 26 cm
Semi-rapid	from 16 to 24 cm
Auxiliary	from 8 to 14 cm

Maintenance and cleaning

Disconnect power before servicing.

All the enameled and glass parts should be cleaned with warm water and neutral solution.
Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for too long.Any food spills (water, sauce, coffee, etc.) should be wiped away before they dry.
Clean with warm water and neutral detergent, and then dry with a soft cloth or chamois. Remove baked-on dirt with specific cleaners for stainless steel surfaces.NOTE: clean stainless steel only with soft cloth or sponge.- – Do not use abrasive or corrosive products, chlorine-based cleaners or pan scourers.- – Do not use steam cleaning appliances.- – Do not use flammable products.- – Do not leave acid or alkaline substances, such as vinegar, mustard, salt, sugar or lemon juice on the hob.

CLEANING THE HOB PARTS

Grids, burner caps and burners can be removed to be cleaned. Do not wash them in the dishwasher.
Clean them by hand with warm water and non-abrasive detergent, removing any food residues and checking that none of the burner openings is clogged.
Rinse and dry
Refit burners and burner caps correctly in the respective housings.
When replacing the grids, make sure that the pan stand area is aligned with the burner.
Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to ensure correct operation. Check these items frequently, and if necessary, clean them with a damp cloth. Any baked-on food should be removed with a toothpick or needle.NOTE: to avoid damaging the electric ignition device, do not use it when the burners are not in their housing. To ensure your appliance is always working correctly, check all functions on the product periodically (eg. every 12 months), that it is operating correctly, and if there appears to be any abnormalities please contact the service call center for advice.

For further details please refer to the warranty terms and conditions provided inside the back of the user manual. Regular care and maintenance ensures correct operation and high performance. To maintain your hob in perfect condition, clean it after every use, removing any food spills.

What to do if …

Problem	Possible cause	Solution
The electric ignition does not work	There is no electrical supply	Check the unit is plugged in and the electrical supply is switched on.
The burner fails to ignite	The gas tap could be closed	Check that the gas tap is open
The gas ring burns unevenly	Burner crown may be occluded by food residues	Clean the burner crown according to cleaning instructions to make sure that the burner crown is clear of food residues.

Before calling the After-Sales Service:

Check “Troubleshooting guide” to see if you can eliminate the problem yourself
Turn the hob on again to check if correct operation has been restored.
If the problem persists, contact the After- sales Service.

Give the following information:

Type of fault;
Hob model;
Service number (i.e. the number after the word SERVICE on the dataplate under the hob and on the warranty certificate);
your full address;
your telephone number.If any repairs are required, contact an authorised service centre, indicated in the warranty.In the unlikely event that an operation or repair is carried out by an unauthorized technician, always request certification of the work carried out and insist on the use of original spare parts. Failure to comply with these instructions may compromise the safety and quality of the product.

Injector table

Model HTB S80S

Gas Type	NATURAL @ 1.00 kPa (test point pressure)	PROPANE @ 2.75 kPa (inlet pressure)
Burner	Nominal Gas Consumption (MJ/h)	Nominal Injector Size (mm)	Nominal Gas Consumption (MJ/h)	Nominal Injector Size (mm)
Auxiliary	4.1	0.90	3.7	0.53
Semi-Rapid	7.8	1.25	7.2	0.73
Rapid	1 .8	1.55	10.8	0.90

Technical data

Model identification: SMÅKOKA 902.851.69
Product Dimensions
Width (mm)	580
Height (mm)	40
Length (mm)	510
Voltage (V)	220 – 240

The technical information are situated in the rating plate on the bottom side of the appliance.

Note: A duplicate Data Plate provided with the appliances should be affixed adjacent to the appliance nearby on a cabinet or area where it is easily accessible for reference.

Before installing the hotplate consider the location of the gas supply and routing the gas line

Installation

After unpacking the hob, make sure that it has not been damaged during transport. In the event of problems, contact the dealer or your nearest After-sales Service.

Technical information for the installer

This product can be embedded in a worktop 20 to 50 mm thick.
If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must be positioned in no case less than 20 mm from the bottom of the hob.
Before installation, make sure that:
the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table);
the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations;

Gas connection

This operation must be performed by a qualified technician or authorised person.

The gas supply system and installation must comply with local regulations to the current relevant gas standard (AS/NZS 5601 current edition).

You can find specific local regulations for some countries in the paragraph
“Reference to Local Regulations”. If no information concerning your Country is given, please ask details to a qualified technician or authorised person.
The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel pipe with fittings complying with local regulations.

This appliance is not connected to a fume exhaust device. It shall be installed in accordance with current installation regulations. Particular attention shall be given to the relevant requirement regarding ventilation.
Combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans.
Connect elbow (A) or (B) supplied with to the hob inlet main pipe and interpose the washer (C) supplied, in compliance with EN 549.
Washer (D) not supplied with the product.
WARNING: THIS PRODUCT IS NOT SUITABLE FOR A FLEXIBLE HOSE CONNECTION.
position
to minimum position to check flame stability

Electrical connection

WARNING

This operation must be performed by a qualified technician or authorised person.
The electrical connections must comply with local regulations.
The earthing of this appliance is compulsory by law.

Earth (yellow/green)

Do not use an extension cord.
IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.

Assembly

After having cleaned the perimeter surface, apply the supplied gasket to the hob. Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.

NOTE: the power supply cable must be long enough to permit its upward extraction. To secure the hob, use the brackets provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance with the thickness of the worktop. Make sure that the outlet is near the product to install. So, if the cable that came with the product is not long enough, you will need to replace it with another one having the same features but with the right length.

Adjustment to different type of gas

WARNING

This operation must be performed by a qualified technician or authorised person.
If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the injectors.
Remove the information label and keep it with the instructions booklet. Use pressure regulators suitable for the gas pressure indicated in the Instruction.

Ensure to remove the natural gas regular device and replace with the propane / lpg test point adaptor.

The gas nozzles must be changed by After Sales Service or a qualified technician or authorised person.
Nozzles not supplied with the appliance must be ordered from After Sales Service.
Adjust the minimum setting of the taps. NOTE: when liquid petroleum gas is used (eg. G30/G31), the minimum gas setting screw must be tightened as far as it will go, or until the flame is small and stable enough to keep it alive.

IMPORTANT: should you experience difficulty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap if found to be faulty.

Replacing the injectors (see paragraph “injector table”)

Remove grids (A).
Extract burners (B).
Using a socket spanner of the appropriate size unscrew the injector (C), unscrew the injector to be replaced.
Replace it with the injector suitable for the new type of gas.
Re-assemble the injector in (D).

Before installing the hob, remember to affix the gas calibration plate supplied with the injectors in such a way that it covers the existing information relating to gas calibration.

Replacement of the gas injector

Adjusting minimum gas setting of taps

To ensure that the minimum setting is correctly adjusted, remove the knob (E) and proceed as follows:

tighten screw to reduce the flame height (-);
loosen screw to increase the flame height (+).

The adjustment must be performed with the tap in minimum gas setting position (small flame ) .

The primary air of the burners does not need to be adjusted.
At this stage, light up the burners and turn the knobs from max position to minimum position to check flame stability. Upon completion of adjustment, reseal the work surface using sealing wax or an equivalent material.

SERVICE INSTRUCTIONS

Service and maintenance only to be carried out by an authorised person.

To replace parts such as burners, valve and electric components, the hotplate must be removed from the bench top by releasing the attachment hooks, loosening the attachment screws of each burner, unscrewing the hotplate attachments nuts which are visible at the bottom of the surface, removing the hotplate top, taking care to remove lid taps and screws under them, and finally replacing the defective parts.

Note: If the valves must be replaced, first disassemble the chain of ignition switches. It is recommended to replace the valve gaskets each time the valve is replaced, thus ensuring a perfect seal between the body and the gas train.

KNOBS REPLACEMENT

Be sure that your hob is switched-off! All knobs must be in closed position.

Pull upwards each knob of the cooktop and store together after removal. Push each of knob on the valve shaft until you feel the end of sliding (sparking may occur).

Make sure that all the knobs are in the right position.

Take the kit with new knobs, which is located in upper part of packaging and remove the new knobs from the plastic bag.

Environmental concerns

How long is the IKEA guarantee valid? This guarantee is valid for five (5) years from the original date of purchase of your appliance at IKEA, unless the appliance is named LAGAN in which case two (2) years of guarantee apply. The original sales receipt, is required as proof of purchase. If service work is carried out under guarantee, this will not extend the guarantee period for the appliance.

Which appliances are not covered by the IKEA five (5) years guarantee?

The range of appliances named LAGAN .

Who will execute the service?

IKEA has appointed Whirlpool (Australia) Pty Ltd as the authorised service network partner.

If you encounter any trouble with the appliance and wish to register a call with Whirlpool, please call: Australia contact centre: 1300 363 344.

What does this guarantee cover? The guarantee covers applicable faults of the appliance, as per the terms and

conditions, from the date of purchase from IKEA. This guarantee applies to domestic use only. The exceptions are specified under the headline “What is not covered under this guarantee?” Within the guarantee period, the costs to remedy the fault e.g. repairs, parts, labour and travel will be covered, provided that the appliance is accessible

for repair without special expenditure. Replaced parts become the property of

IKEA.

The services will be in-home service for domestic appliances, and must to be done by official Whirlpool service network.

Goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired.

Refurbished parts may be used to repair the goods.

If the authorized service agent requests you to deliver the product directly to them, please ensure that the appliance is suitably packaged to prevent any damage during transportation.

What will IKEA do to correct the problem? IKEA appointed service provider will examine the product and decide, at its

sole discretion, if it is covered under this guarantee. If considered covered, IKEA service provider or its authorized service partner through its own service operations, will then, at its sole discretion, either repair the defective product or replace it with the same or a comparable product.

What is not covered under this guarantee?

Normal wear and tear.
Deliberate or negligent damage, damage caused by failure to observe operating and maintenance instructions, incorrect installation or by connection

to the wrong voltage, damage caused by chemical or electrochemical reaction, rust, abrasion or scratching, corrosion or water damage including but not limited to damage caused by excessive lime in

the water supply, damage caused by abnormal environmental conditions.

Damage caused from the use of the appliance in a manner other than the use for which it was specifically designed.
Damage caused by power outages, electrical power surge or improper supply voltage via connection to Supply Authority mains or alternative supply systems.
Consumable parts including batteries and lamps, removable wire, glass and plastic trays and other accessories.
Internal or external damage as a result of excessive use of cleaning products or cleaning agents.
Non-functional and decorative parts which do not affect normal use of the appliance, including any scratches and possible color differences.
Accidental damage or blockages caused by foreign objects, eg. coins, underwires, nails, buttons or jewellery, or substances and cleaning or unblocking of filters, drainage systems or soap drawers
Damage caused by vermin, insects or pets.
Note – internal or external cabinet transport damage must be reported within 7 days of purchase date.
Damage to the following parts: ceramic glass, accessories, crockery and cutlery baskets, feed and drainage pipes, seals, lamps and lamp covers, screens, knobs, casings and parts of casings. Unless such damages can be proved to have been caused by production faults.
Cases where no fault could be found during a technician’s visit.
Any consequential loss due to appliance failure.
Repairs not carried out by our appointed service providers and/or an authorized service contractual partner

or where non original parts have been used.

Repairs to parts or systems caused by unauthorized modifications made to appliance.
Repairs caused by installation which is faulty or not according to specification.
Problems caused by incorrect or inadequate venting of the appliance.
The use of the appliance in a non domestic environment i.e. professional use.
Transportation damages. If a customer transports the product to his home or another address, IKEA is not liable for any damage that may occur during transport.

However, if IKEA delivers the product to the customer’s delivery address, then damage to the product that occurs during this delivery will be covered by IKEA.

Cost for carrying out the initial installation of the IKEA appliance. However, if an IKEA appointed service provider or its authorized service partner repairs or replaces the appliance under the terms of this guarantee, the appointed service provider or its authorized service partner will reinstall the repaired appliance or install the replacement, if necessary.
The benefits conferred by this express warranty are in addition to all other conditions, warranties, guarantees, rights and remedies expressed or implied by the Trade Practices Act and similar State and Territory laws and all other obligations and liabilities on the part of the manufacturer or supplier and nothing contained herein shall restrict or modify such rights, remedies, obligations or liabilities.

How country law applies?

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.

You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Area of validity

The IKEA guarantee applies only to products purchased and installed in AUSTRALIA .

The dedicated AFTER SALES for IKEA appliances

Please don’t hesitate to contact IKEA appointed After Sales Service Provider to:

make a service request under this guarantee;
ask for clarifications on installation of the IKEA appliance in the dedicated IKEA kitchen furniture;
ask for clarification on functions of IKEA appliances.
Call our authorized service network partner Whirlpool on 1300 363 344 (Australia).

WARRANTY PROCEDURE

Please ensure that installation procedure entailed in the user manual has been adhered to and in case of any doubts please refer to the trouble shooting guide that has been supplied with the appliance.

Please read the user guide to ensure that you are aware of all the features & benefits of the appliance.

How to reach if you need our service The Whirlpool call centre team will assist you on the phone with basic trouble shooting for your appliance at the time of warranty call registration. Please describe the problem that you are facing with the appliance in detail along with your product model number, serial number, date of purchase at the time of call registration.

Please also always refer to the IKEA article number (8 digit code) and 12 digit service number placed on the rating plate of your appliance.

SAVE THE SALES RECEIPT! Kindly keep all these details and original invoice of purchase handy during the service technician’s visit to enable him to carry out the job. Whirlpool reserves the right not to register the call under warranty if you fail to provide these details at the time of call registration.

Do you need extra help?

For any additional questions not related to After Sales of your appliances please contact your nearest IKEA store call centre. We recommend you read the appliance documentation carefully before contacting us.For details on service agents locations, please visit – www.whirlpool.com.au/services.

IKEA SMAKOKA User Manual – IKEA SMAKOKA User Manual –

[xyz-ips snippet=”download-snippet”]

Posted

2023-01-13

Ikea

admin

Tags:

Ikea, IKEA SMAKOKA