STYRBAR
Remote control functions
 |
Short press to turn on. To dim up, press and hold the button. |
 |
Short press to turn off. To dim down, press and hold the button. |
 |
Change white spectrum or colors. |
 |
Pairing: Add IKEA Smart Lighting products to your system. See instructions below. |
Adding devices to your remote controlWhen the remote control is sold together with a light source (in the same package), they are already paired. If the remote control is purchased separately, you must manually pair it to your light source.
To add light sources, just repeat the steps below.
- Make sure that your light source is installed and the main power switch is turned on.
- Hold the remote control close to the light source you want to add (no more than 5 km away).
- Press and hold the pairing button
for at least 10 seconds. A red light will shine steadily on the remote control. Your light source will begin to dim and flash one time to indicate that it has been successfully paired.
Up to 10 light sources can be paired with 1 remote control. Make sure to pair them one at a time. If the light sources are close to each other, disconnect those that have already been paired from the main power switch.
Factory reset your devices For light sources:Toggle the main switch 6 times.For remote control:Press the pairing button 4 times within 5 seconds.SynchronizingIf your light source becomes unsynchronized, a long press on the left (<) or right (>) buttons will return the light source to its default setting (2700K).Changing the batteryWhen the remote control is used regularly and as intended, the batteries will last for approximately 2 years.When it’s time to replace the battery, a red LED indicator will flash when you press any button on the remote control.Open the battery lid and replace the battery with two new AAA/HR03 batteries.Caution!Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.Important!
- The remote control is for indoor use only and can be used in temperatures ranging from 0ºC to 40 ºC.
- Do not leave the remote control in direct sunlight or near any heat source, as it may overheat.
- The range between the remote control and the receiver is measured in the open air.
- Different building materials and placement of the units can affect the wireless connectivity range.
Care instructions
To clean the remote control, wipe with a soft cloth moistened with a little mild detergent. Use another soft, dry cloth to wipe dry.Note!Never use abrasive cleaners or chemical solvents as this can damage the product.Recommended battery types:2 x IKEA LADDA 900 (AAA/HR03, 1.2V, 900mAh,Ni-MH) (Not included)Do not mix batteries of different capacities, types, or date stamps.
TECHNICAL DATA
Type: E2001Name: STYRBAR Remote control stainlessType: E2002Name: STYRBAR Remote control whiteInput: 3V, 2x AAA/HR03 LADDA batteriesRange: 10 m in the open air.For indoor use onlyOperating frequency: 2405-2480 MHzOutput power: 12.6 dBm (EIRP)IP-class: IP44Manufacturer: IKEA of Sweden ABAddress:Box 702, SE-343 81 Älmhult, SWEDEN
Declaration of Conformity
Hereby, IKEA of Sweden AB declares that the radio equipment type E2001/E2002 is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity can be found at http://www.ikea.com – Choose the country you are in– Search your product in the search field– Go to Assembly Instructions and Manuals (downloads) Here will you find a pdf file of the full DoC.
The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment. For more information, please contact your IKEA store.
report this ad
© Inter IKEA Systems B.V. 2020AA-2248601-2
References
[xyz-ips snippet=”download-snippet”]