WIRELESS CHARGING PADQUICK START GUIDE
IMPORTANT SAFETY INSTRUCTIONS for Jensen PCHQIT5
Failure to follow the safety instructions can lead to fire, electrical shock, personal injury or property damage or damage to this product. Make sure to read this entire manual.
- Do not use this product for anything other than its intended use.
- Keep this product away from heat sources and direct sunlight.
- Do not expose this product to extremely high or low temperatures. Use it in an ambient temperature between 32ºF (0ºC) and 95ºF (35ºC).
- Do not let this product come in contact with water or other liquids. If the product gets wet, unplug it immediately from its power source.
- Do not handle the product, USB cable, or wall charger with wet hands.
- Do not let dust or other particles accumulate on the product or wall charger.
- Do not use this product if it’s been dropped or damaged in any way.
- Repairs to electrical equipment should only be performed by a qualified electrician. Improper repairs might place the user at serious risk.
- If you have a pacemaker or other implanted electrical device, consult your physician before using this product.
- Do not place magnetic objects near this product.
- Make sure the wall charger is inserted all the way into the power outlet. Unplug the wall charger when the product is not in use.
- Place the product on a flat, sturdy surface during charging.
- Keep this product out of reach of children.
Care and cleaning
Wipe of any accumulated dust using a soft, dry cloth. Never use abrasive cleaning agents of any kind.
FCC NOTICE (for USA)
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’sauthority to operate the product.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
INDUSTRY CANADA NOTICE
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.The “Qi” symbol is a trademark of the Wireless Power Consortium.
Charging your device
IMPORTANT: Before you try to charge your device, make sure it is compatible with wireless charging. If your device has a metal case, remove it before you put the device on the charger.
- Plug one end of the provided micro USB cable into the Wireless Charging pad. Plug the other end into a USB charger or other USB power source.Note: For fastest charging, use the USB charging adapter that came with your device.
- Place your device directly onto the charging pad. Refer to the placement illustrations here as a guide.
The charger’s indicator light is solid green when charging. The indicator turns off when your device is fully charged (if your device is turned on, it’s still drawing power, so the indicator light might stay on even after the device is charged).The indicator light flashes if there’s a problem with wireless charging, such as a foreign object between your device and the charging pad. Your device screen displays the charging progress. You can remove your device at any time during charging.Note: The charger’s indicator flashes three times then turns off when you plug it in. It remains off when the charger’s not charging a device.
- When your device is completely charged, remove it from the charging pad.
[xyz-ips snippet=”download-snippet”]