User ManualCarlitaPendant
Thank you for purchasing this Carlita Pendant. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please keep these instructions for future reference.
Warnings!This is a Class 1 product and must be earthed.Please read these instructions carefully before commencing any work. It is recommended that this fitting is installed by a qualified electrician.Install in accordance with the IEE Wiring regulations and the Building Regulations.To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge.If you are in any doubt, please consult a qualified electrician.This light fitting should be connected to a 5 amp fused circuit.If replacing an existing fitting, make a note of the connections.Always use the correct type and wattage bulb. Never exceed the wattage stated.When changing a bulb or adjusting the heads, always switch off at the mains and allow to cool down. Dispose of used bulbs carefully.This product is suitable for indoor use only.This product is suitable for installation on surfaces with normal flammability e.g. wood, plasterboard, masonry. It is not suitable for use on highly flammable surfaces (e.g. polystyrene, textiles).For your safety, always switch off the supply before changing lightbulbs, cleaning or removing shades. Always take care when handling lightbulbs to avoid injury in case of breakage.
Parts List
Light Fitting | 1 | Screws | 2 | ||
Wall plugs | 2 | ||||
Candle drips | 5 |
Installation InstructionsRefer to assembly diagrams. Carefully unpack the carton, making sure all the parts are present before assembly.
Adjusting the DropPlease note that the drop of this product can be reduced by removing chain links. Always ensure that the weight of the fitting is supported by the chain and not the cable.
Repositioning ArmsTo reduce the packaging, the arms on this fitting have been deliberately moved out of position. Before installation, the arms must be correctly re-positioned by hand into equally spaced positions. Each arm has a spring washer fitted to it to enable the arm to be re-positioned without the need for loosening and retightening the nut. Simply rotate each arm into the correct position.
Step 1Before removing the existing fitting, carefully note the position of each set of wires.
Step 2Remove the fixing strap (A) from the fitting by removing side screws (B) and washers (C) (see Figure 1). Using the screws provided in the fixing pack, secure the strap to the ceiling, making sure that there is a joist at the point of fixing to support the weight of the product.Take care to avoid damaging any concealed wiring and pipes.
Step 3Having identified the household wiring from your existing light fitting, connect to the connection block inside the product in the following way:
Check that…..You have correctly identified the house wires.The connections are tight.No loose strands have been left out of the connection block.
Step 4When completed, ensure that there are no bare or loose strands of wire exposed, and cover all exposed areas of the connection block with 2 layers of insulation tape.
Step 5Attach the product to the fixing bracket using side screws (B) and washers (C) (see Figure 1), by locating the screws in the bracket into the holes in the ceiling cover and tightening the screws to secure.
Step 6When fitting a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of used bulbs carefully. Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting.Some Energy saver bulbs are not suitable for use with a dimmer switch.Replace fuse or circuit breaker and switch on.Your light is now ready for use.
For useWe recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish.
Recommended bulb5 x 60WSES E14 Candleor
5 x 42WSES Eco Halogen Candle
When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of used bulbs carefully. Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting.
SpecificationMaximum wattage:60WVoltage: 240V, 50HzIP Rating: 20Weight: 2.3kg
This symbol
We have taken great care to ensure that this product reaches you in perfect condition. However, should any parts be damaged or missing please contact our Product Helpline on (01202) 690945.
John Lewis Partnership171 Victoria StreetLondon SW 1E 5NNjohnlewis.com
Made in China 04/02/2021
References
[xyz-ips snippet=”download-snippet”]