Johan LewisTom Floor lampUser Manual
Thank you for purchasing this Tom floor lamp. Please read the instructions carefully before use to ensure safe and satisfactory operations of this product.
Please keep this instruction for future reference.
Warnings!
- The supply cable runs through the inside of this product. Take care not to place undue stress on the cable whilst unpacking to prevent the possibility of a poor connection.
- If you are in any doubt consult a person competent to give advice on the assembly of electrical equipment.
- If the external flexible cable of the lamp is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
- To prevent electrocution switch off at the mains supply before assembling or maintaining this fitting. Ensure the plug is not connected to any power supply and read instructions before assembly.
- Always be sure to use the correct type and wattage of bulbs as indicated on the fitting. Never exceed the wattage stated.
- When changing the bulb, always switch off at the mains and allow the old bulb to cool down before handling. Dispose of used bulbs carefully.
- Caution! The bulb and surrounding parts can become hot during use.
- For indoor use only.
Care instructions
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as these will damage the finish.Replace bulbs from John Lewis or established brand of the same type and compatibility.
Parts list
Assembly
Never assembly your appliance on a wet, freshly painted surface. Ensure to off at the mains supply before assembling or maintaining this fitting.
Step 1
Unpack the product and remove all packaging. Be careful not to scratch the surface of the product whilst removing the wrapping.Lay the product out on the floor. If the floor is not carpeted please cover it with a soft cloth to avoid damage to the flooring and surface of the product. Assembly should take place with the product lying flat.Screw the centre pole onto the upper lamp holder section ensuring that the lamp holder section is kept still and that the pole is threaded on ensuring that the cable does not twist.
Step 2
Screw the lower pole onto the centre pole ensuring that the centre pole is kept still and that the pole is threaded on ensuring that the cable does not twist.Gently pull any excess supply cable through the small hole in the base until it meets the pole assembly.Insert the assembled poles into the receiving collar on the base section. Insert and fully tighten the two grub screws at the rear of the floor lamp using the hex key provided to secure the assembly in place.Stand the floor lamp upright and ensure all the assembled parts are fully tightened.Loosen the screw on the saddle cable clamp located inside the base section. Place the electrical cable from the floor lamp under the clamp and retighten to lock the cable in place. Take care not to damage the wiring. Attach the foam pad onto the base of the product to protect the floor when in use.
Step 3
To fit shade: Remove the shade ring from lamp holder, fit the shade and replace shade ring to secure in place. Take care not to overtighten as this may cause damage to the fitting.
Fit the bulb, type and wattage as indicated on the fitting (bulb not supplied). The wattage indicated must not be exceeded.
Floor lamp is now ready for use.
Recommended bulb
- 1 x 6-9 Watt E27 (ES) energy efficient LED GLS bulbOr
- 1 x 42W E27 eco halogen GLS bulb
- Bulb not included
Specification
- Max power: 42W
- Voltage: 220~240V, 50Hz
- IP20
- Weight 3.8Kg
Please retain these instructions for future reference.This symbolindicates that this product should not be treated as normal house-hold waste and it should be recycled. John Lewis does not operate in store take back, but as members of the Distributer Take Back scheme have funded the development and upgrade of recycling facilities across the UK. Please take it to your nearest collection facility or for further details contact your local council or visit www.recycle-more.co.uk.We have taken great care to ensure that this product reaches you in perfect condition. However, should any parts be damaged or missing please e-mail
Trouble shooting:
Why is the light not working when switched on?Check your power supply is switched on Turn off light and check that the bulb is inserted correctly Check the bulb is still in working order.
John Lewis partnership171 Victoria StreetLondon SW1E 5NN Johnlewis.com
Made in China
References
[xyz-ips snippet=”download-snippet”]